Zhiqian Yin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Zhiqian Yin has a total of 42 co-authors. Here are the top co-authors by number of shared publications:
- Xiangfei Chen
Nanjing University
4 shared publications - Zhenxing Sun
YongJiang Laboratory
4 shared publications - Jiaqiang Nie
Key Laboratory of Intelligent Optical Sensing and Manipulation of the Ministry of Education, National Laboratory of Solid State Microstructures, College of Engineering and Applied Sciences, Institute of Optical Communication Engineering, Nanjing University, Nanjing, China
3 shared publications - Rulei Xiao
Nanjing University
3 shared publications - Tao Fang
Key Laboratory of Intelligent Optical Sensing and Manipulation of the Ministry of Education & Engineering Research Center of Precision Photonics Integration and System Application of the Ministry of Education & National Laboratory of Solid State Microstructures & College of Engineering and Applied Sciences & Nanjing University-Tong ding Joint Lab for large-scale photonic integrated circuits & Key Laboratory of Intelligent Optical Sensing and Manipulation, Ministry of Education, Nanjing U
3 shared publications - Yunshan Zhang
Nanjing University of Posts and Telecommunications
3 shared publications
Latest Publications
- 1 October 2026
- Published by IOP Publishing in Journal of Optics
- Vol. 28 (10) , 105702
Long-term stability enhancement of RF phase-stabilized fiber transmission using a dual-transceiver architecture
Conventional single-transceiver radio-frequency (RF) phase-stabilized fiber transmission systems suffer from degraded error-signal detection accuracy over long transmission distances because of return-link signal attenuation. To overcome this limitation, a 55 km RF phase-stabilized fiber transmission system based on a dual-transceiver architecture is proposed and experimentally demonstrated. Independent directly modulated lasers (DML) are employed at the central and remote sites to realize bidirectional transmission using independent optical carriers, thereby enhancing the return-link optical power, recovered RF signal power, and the signal-to-noise ratio of the error-signal detection. In addition, both fiber-link propagation disturbances and intrinsic phase drifts of the transmitting and receiving modules are incorporated into the compensation loop, improving the long-term phase-error suppression capability at the system-architecture level. The influences of power-supply stability, mixer input-power matching, and environmental temperature fluctuations on the long-term stability are systematically investigated, while the characteristics of the DMLs and the residual stability are also experimentally evaluated. Experimental results show that, over a 55 km fiber link under a 70 000 s environmental temperature perturbation, the peak-to-peak residual delay fluctuation remains within 0.135 ps. The corresponding modified Allan deviation reaches 5.4705 × 10 −15 at 1 s and 1.6194 × 10 −19 at 10 000 s. These results verify the effectiveness of the proposed dual-transceiver architecture in improving the long-term stability of RF phase-stabilized fiber transmission systems and demonstrate that it provides an effective solution for long-distance dissemination of ultra-stable RF reference signals.
- 1 October 2026
- Published by IOP Publishing in Journal of Optics
- Vol. 28 (10) , 105702
Long-term stability enhancement of RF phase-stabilized fiber transmission using a dual-transceiver architecture
Conventional single-transceiver radio-frequency (RF) phase-stabilized fiber transmission systems suffer from degraded error-signal detection accuracy over long transmission distances because of return-link signal attenuation. To overcome this limitation, a 55 km RF phase-stabilized fiber transmission system based on a dual-transceiver architecture is proposed and experimentally demonstrated. Independent directly modulated lasers (DML) are employed at the central and remote sites to realize bidirectional transmission using independent optical carriers, thereby enhancing the return-link optical power, recovered RF signal power, and the signal-to-noise ratio of the error-signal detection. In addition, both fiber-link propagation disturbances and intrinsic phase drifts of the transmitting and receiving modules are incorporated into the compensation loop, improving the long-term phase-error suppression capability at the system-architecture level. The influences of power-supply stability, mixer input-power matching, and environmental temperature fluctuations on the long-term stability are systematically investigated, while the characteristics of the DMLs and the residual stability are also experimentally evaluated. Experimental results show that, over a 55 km fiber link under a 70 000 s environmental temperature perturbation, the peak-to-peak residual delay fluctuation remains within 0.135 ps. The corresponding modified Allan deviation reaches 5.4705 × 10 −15 at 1 s and 1.6194 × 10 −19 at 10 000 s. These results verify the effectiveness of the proposed dual-transceiver architecture in improving the long-term stability of RF phase-stabilized fiber transmission systems and demonstrate that it provides an effective solution for long-distance dissemination of ultra-stable RF reference signals.
- 19 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 43 (17) , 8358-8366
A Low-Cost Hybrid Integrated Narrow Linewidth Laser Based on REC and PWB Techniques
A low-cost hybrid integrated narrow linewidth laser is proposed in this paper. The monolithically integrated 18- channel distributed feedback (DFB) narrow linewidth laser array with a wavelength interval of 0.8 nm is designed and precisely fabricated using reconstruction equivalent chirp (REC) technique, exhibiting good single-mode performance for each channel, with the typical linewidth less than 200 kHz. One channel of the laser array is integrated with the silicon nitride (Si3N4) external cavity chip through the photonic wire bonding (PWB) technique. Both the linewidth reduction effect of the passive external cavity and the coupling efficiency between chips by the polymer waveguide are numerically calculated. The compactly packaged device can be tuned to seven distinct self-injection-locked states with 0.4 nm spectral spacing, where the maximum linewidth is 10.9 kHz and the minimum linewidth is 9.1 kHz. Meanwhile, the side-mode suppression ratio (SMSR) is higher than 54.3 dB and the output power is 3.6 ± 0.9 dBm for each self-injection-locked state.
- 19 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 43 (17) , 8358-8366
A Low-Cost Hybrid Integrated Narrow Linewidth Laser Based on REC and PWB Techniques
A low-cost hybrid integrated narrow linewidth laser is proposed in this paper. The monolithically integrated 18- channel distributed feedback (DFB) narrow linewidth laser array with a wavelength interval of 0.8 nm is designed and precisely fabricated using reconstruction equivalent chirp (REC) technique, exhibiting good single-mode performance for each channel, with the typical linewidth less than 200 kHz. One channel of the laser array is integrated with the silicon nitride (Si3N4) external cavity chip through the photonic wire bonding (PWB) technique. Both the linewidth reduction effect of the passive external cavity and the coupling efficiency between chips by the polymer waveguide are numerically calculated. The compactly packaged device can be tuned to seven distinct self-injection-locked states with 0.4 nm spectral spacing, where the maximum linewidth is 10.9 kHz and the minimum linewidth is 9.1 kHz. Meanwhile, the side-mode suppression ratio (SMSR) is higher than 54.3 dB and the output power is 3.6 ± 0.9 dBm for each self-injection-locked state.
- 12 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 42 (24) , 8598-8605
Enhanced-Performance Tunable Sources for Fast AWGR-Based Optical Switching Data Center Networks
Optical switching based on arrayed waveguide grating routers (AWGRs) and fast tunable sources is a future-proof solution to overcome the bottleneck of limited bandwidth and high latency of electrical switches-based data center networks (DCNs). To support fine-grained optical packet switching and maintain high network throughputs, tunable sources capable of nanosecond-scale hitless wavelength switching are critical requirements for such fast optically switching networks. In this work, we experimentally demonstrate a fast-tunable source based on a high-density multi-wavelength DFB laser array monolithically integrated with a three-stage Y-branch combiner and an SOA. The DFB laser array has an average 100-GHz channel spacing under the same bias current. The output power of all lasers is above 10 mW, with a uniformity of less than 1 dB. Benefitting from the high-speed dynamic property of the DFB laser and high-speed burst drive pulses controlled by a field-programmable gate array (FPGA), less than 3 ns switching time is achieved by the on-off switching of the DFB laser on arrays, which is independent of tuning range. Furthermore, a 2 × 2 optical switching prototype based on this demonstrated chip and AWGRs achieves error-free transmission atop 25 Gbps NRZ per link with 12.8 ns end-to-end reconfiguration, which provides a path toward a high-bandwidth, low-latency, and energy-efficient wavelength-switched network for data centers in the post-Moore's Law era.
- 12 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 42 (24) , 8598-8605
Enhanced-Performance Tunable Sources for Fast AWGR-Based Optical Switching Data Center Networks
Optical switching based on arrayed waveguide grating routers (AWGRs) and fast tunable sources is a future-proof solution to overcome the bottleneck of limited bandwidth and high latency of electrical switches-based data center networks (DCNs). To support fine-grained optical packet switching and maintain high network throughputs, tunable sources capable of nanosecond-scale hitless wavelength switching are critical requirements for such fast optically switching networks. In this work, we experimentally demonstrate a fast-tunable source based on a high-density multi-wavelength DFB laser array monolithically integrated with a three-stage Y-branch combiner and an SOA. The DFB laser array has an average 100-GHz channel spacing under the same bias current. The output power of all lasers is above 10 mW, with a uniformity of less than 1 dB. Benefitting from the high-speed dynamic property of the DFB laser and high-speed burst drive pulses controlled by a field-programmable gate array (FPGA), less than 3 ns switching time is achieved by the on-off switching of the DFB laser on arrays, which is independent of tuning range. Furthermore, a 2 × 2 optical switching prototype based on this demonstrated chip and AWGRs achieves error-free transmission atop 25 Gbps NRZ per link with 12.8 ns end-to-end reconfiguration, which provides a path toward a high-bandwidth, low-latency, and energy-efficient wavelength-switched network for data centers in the post-Moore's Law era.
- 7 June 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 36 (15) , 921-924
Current-Tuned Tunable In-Series DFB Laser Array Assisted With Thin Film Heater
In this letter, we propose and demonstrate a tunable in-series distributed feedback (DFB) laser array, and the wavelength is continuously tuned with the assistance of the monolithically integrated thin-film heater. Compared with an in-parallel laser array with an optical combiner, the proposed in-series DFB laser array avoids significant power loss resulting from the optical combiner. The three-section structure is utilized to suppress the grating crosstalk among the in-series laser array and guarantees single-mode stabilities. Besides, the reconstruction-equivalent-chirp technique is utilized to simplify grating fabrication and enhance the precise control of the grating phase. Four lasers with wavelength spacings of 2.4 nm are integrated into the in-series laser array and the Ti/Pt thin film heaters are monolithically integrated near the waveguides of each laser unit. The wavelength of the proposed structure is coarsely tuned by selecting the working laser and finely tuned by adjusting the injection current to the laser unit and the thin-film heaters. 9.6 nm continuous wavelength tuning range and fast wavelength tuning are obtained for the proposed in-series laser array without adjusting the temperature of the thermal-electric cooler (TEC). The proposed structure provides a solution for the wavelength tunable laser, which is promised to be used in the dense wavelength division multiplexing (DWDM) systems.
- 7 June 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 36 (15) , 921-924
Current-Tuned Tunable In-Series DFB Laser Array Assisted With Thin Film Heater
In this letter, we propose and demonstrate a tunable in-series distributed feedback (DFB) laser array, and the wavelength is continuously tuned with the assistance of the monolithically integrated thin-film heater. Compared with an in-parallel laser array with an optical combiner, the proposed in-series DFB laser array avoids significant power loss resulting from the optical combiner. The three-section structure is utilized to suppress the grating crosstalk among the in-series laser array and guarantees single-mode stabilities. Besides, the reconstruction-equivalent-chirp technique is utilized to simplify grating fabrication and enhance the precise control of the grating phase. Four lasers with wavelength spacings of 2.4 nm are integrated into the in-series laser array and the Ti/Pt thin film heaters are monolithically integrated near the waveguides of each laser unit. The wavelength of the proposed structure is coarsely tuned by selecting the working laser and finely tuned by adjusting the injection current to the laser unit and the thin-film heaters. 9.6 nm continuous wavelength tuning range and fast wavelength tuning are obtained for the proposed in-series laser array without adjusting the temperature of the thermal-electric cooler (TEC). The proposed structure provides a solution for the wavelength tunable laser, which is promised to be used in the dense wavelength division multiplexing (DWDM) systems.
- 20 December 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 42 (8) , 2880-2886
Optical Circuit Switching Using REC-DFB Laser Array
The ongoing growth of data traffic from existing and new latency-sensitive applications poses a challenge to the data center network. Wavelength-routed optical circuit switching promises high bandwidth, low power and latency networking for data centers, but requires a wideband wavelength tunable source capable of nanosecond-scale hitless wavelength switching at every node. A tunable source based on DFB laser arrays is a potential candidate due to the high-speed dynamic property and high single-longitudinal-mode (SLM) stability of the DFB laser. However, the large-scale integration of the DFB laser and the high precision control of the lasing wavelength are still problems. In this work, we proposed and fabricated a monolithic integrated 16-channel DFB laser array with high SLM stability and 100-GHz channel spacing by using the reconstruction-equivalent-chirp (REC) technique. The maximum output power of each channel was above 6 mW. Based on the custom-designed fast switching drive board with a field-programmable gate array (FPGA), the switch-ON and OFF time between any pair of channel combinations were measured at less than 10 ns. Dynamic switching wavelengths remained stable and resided within the receiver bandwidth. Wavelength switching experiments for modulated light signals were done by driving the external modulator, achieving bit error performance at 1×10 -9 for 10 Gb/s NRZ data.
- 20 December 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 42 (8) , 2880-2886
Optical Circuit Switching Using REC-DFB Laser Array
The ongoing growth of data traffic from existing and new latency-sensitive applications poses a challenge to the data center network. Wavelength-routed optical circuit switching promises high bandwidth, low power and latency networking for data centers, but requires a wideband wavelength tunable source capable of nanosecond-scale hitless wavelength switching at every node. A tunable source based on DFB laser arrays is a potential candidate due to the high-speed dynamic property and high single-longitudinal-mode (SLM) stability of the DFB laser. However, the large-scale integration of the DFB laser and the high precision control of the lasing wavelength are still problems. In this work, we proposed and fabricated a monolithic integrated 16-channel DFB laser array with high SLM stability and 100-GHz channel spacing by using the reconstruction-equivalent-chirp (REC) technique. The maximum output power of each channel was above 6 mW. Based on the custom-designed fast switching drive board with a field-programmable gate array (FPGA), the switch-ON and OFF time between any pair of channel combinations were measured at less than 10 ns. Dynamic switching wavelengths remained stable and resided within the receiver bandwidth. Wavelength switching experiments for modulated light signals were done by driving the external modulator, achieving bit error performance at 1×10 -9 for 10 Gb/s NRZ data.