Mounir Bouchaour
Research Subjects
Research Interests
Mounir Bouchaour has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Azzedine Adouane
Research Unit in Optics and Photonics (UROP), Centre for the Development of Advanced Technologies (CDTA), Setif, Algeria
3 shared publications - Abdelhak Guermat
Research Unit in Optics and Photonics (UROP), Centre for the Development of Advanced Technologies (CDTA), Setif, Algeria
2 shared publications Abdelhak Guermat
Non-linear Optics and Optical fiber team (ONLFO), Research Unit in Optics and Photonics(UROP), Centre for the Development of Advanced Technologies(CDTA), University of Setif-1, 19000 Setif, Algeria
1 shared publicationAssia Guessoum
Laboratoire d’Optique Appliquée [AppliedOpticsLaboratory], Institut d’Optique et Mécanique de Précision (Institute of Optics and PrecisionMechanics, Université Ferhat ABBAS Sétif 1 - Campus (Ex. Travaux Publics) Avenue Saïd Boukhraïssa, Maabouda, 19000 Sétif, Algeria
1 shared publication- Assia Guessoum
Laboratoire d’Optique Appliquée [AppliedOpticsLaboratory], Institut d’Optique Et Mécanique de Précision (Institute of Optics and Precision Mechanics), Ferhat Abbas University Setif1, Setif, Algeria
1 shared publication - Assia Guessoum
Faculty of Physics, Quantum Electronics Laboratory, Houari Boumediene University of Science and Technology, Algiers, Algeria
1 shared publication
Latest Publications
- 29 August 2026
- Published by Springer Nature in Optical and Quantum Electronics
- Vol. 58 (11) , 499
Simulation study of a ZnO-based interferometric sensor on a microstructured GI-MMF fiber for simultaneous detection of temperature and refractive index
- 29 August 2026
- Published by Springer Nature in Optical and Quantum Electronics
- Vol. 58 (11) , 499
Simulation study of a ZnO-based interferometric sensor on a microstructured GI-MMF fiber for simultaneous detection of temperature and refractive index
- 26 June 2024
- Published by Springer Nature in Optical and Quantum Electronics
- Vol. 56 (7) , 1-20
Study by simulation and realization of a fiber optic pressure sensor based on a PDMS flexible µ-membrane
- 26 June 2024
- Published by Springer Nature in Optical and Quantum Electronics
- Vol. 56 (7) , 1-20
Study by simulation and realization of a fiber optic pressure sensor based on a PDMS flexible µ-membrane
- 8 November 2023
- Published by IOP Publishing in Physica Scripta
- Vol. 98 (12) , 125508
Investigation by simulation of the highest sensitivity interferometric pressure sensor at the end of a micro-structured optical fiber
One of the most prevalent techniques used in the construction of optical fiber-based pressure sensors is Fabry–Perot interferometry. This work presents a variety of interferometric sensors based on this feature. To achieve this, we used chemical etching (HF) to create conical cavities at the ends of the optical fibers single mode fiber (SMF) and graded index (GRIN) fiber, where the first gold (Au) deposition allows us to create half-mirrors. So the interface (core/Au) represents the first reflective surface. After filling each micro-cavity with a quantity of polydimethylsiloxane (PDMS) type polymer to form a flexible micro-lens, and proceeding to a second deposition of gold (Au), we got the second reflective surface (PDMS/Au). The sensor with the highest sensitivity to pressure and temperature, namely 0.065 nm/KPa and 0.24 nm/°C, was obtained for a micro-cavity length of 35 μm, a diameter of 60 μm, and a micro-lens thickness of 20 μm, respectively. Analysis and simulation were performed using COMSOL Multiphysics to develop the sensor.
- 8 November 2023
- Published by IOP Publishing in Physica Scripta
- Vol. 98 (12) , 125508
Investigation by simulation of the highest sensitivity interferometric pressure sensor at the end of a micro-structured optical fiber
One of the most prevalent techniques used in the construction of optical fiber-based pressure sensors is Fabry–Perot interferometry. This work presents a variety of interferometric sensors based on this feature. To achieve this, we used chemical etching (HF) to create conical cavities at the ends of the optical fibers single mode fiber (SMF) and graded index (GRIN) fiber, where the first gold (Au) deposition allows us to create half-mirrors. So the interface (core/Au) represents the first reflective surface. After filling each micro-cavity with a quantity of polydimethylsiloxane (PDMS) type polymer to form a flexible micro-lens, and proceeding to a second deposition of gold (Au), we got the second reflective surface (PDMS/Au). The sensor with the highest sensitivity to pressure and temperature, namely 0.065 nm/KPa and 0.24 nm/°C, was obtained for a micro-cavity length of 35 μm, a diameter of 60 μm, and a micro-lens thickness of 20 μm, respectively. Analysis and simulation were performed using COMSOL Multiphysics to develop the sensor.