Chao Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Chao Wang has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Chen Xu
School of Naval Architecture, Ocean and Energy Power Engineering, Wuhan University of Technology, Wuhan 430063, China
2 shared publications - Yijun Mao
School of Aerospace Engineering, Huazhong University of Science and Technology, Wuhan 430074, China
2 shared publications - Chunshan Ou1 shared publication
Guo Yao
1 shared publication- Hongxing Hua
State Key Laboratory of Mechanical System and Vibration, Shanghai Jiao Tong University, Shanghai, China
1 shared publication - Jidong Tian
State Key Lab of Advanced Optical Communication System and Network, Shanghai Jiao Tong University, China
1 shared publication
Latest Publications
- Open Access
- 1 February 2026
- Published by AIP Publishing in AIP Advances
- Vol. 16 (2)
Sequential optimization of spiral structures for simultaneous noise reduction and flow drag minimization
Spiral acoustic structures hold significant potential for noise suppression in fluid flow systems; however, their aerodynamic performance has often been overlooked in previous studies. To bridge this gap, the present study develops a sequential optimization strategy aimed at simultaneously maximizing acoustic transmission loss (TL) and minimizing flow drag (FD). The strategy integrates a multi-objective genetic algorithm with surrogate models for initial global exploration of the design space, followed by an adjoint optimization method for local refinement of the inner wall geometry. Under fixed outer dimensions, the spiral geometry is parameterized using inner diameter, spiral angular frequency, spiral position, and dimensionless pitch. Sensitivity analysis is employed to identify the key structural parameters. Surrogate models are constructed to efficiently map the structural parameters to FD and total transmission loss (TY), respectively. A multi-objective genetic algorithm identifies a multi-objective optimization structure achieving TY higher than 7 dB and reducing FD by 306.35 Pa at 10 m/s compared to the original structure. The adjoint optimization, building upon this multi-objective optimization structure result, further reduces the FD by an additional 89.33 Pa without compromising the TL. The sequential optimization strategy ultimately delivers a 23% increase in TY and a 53.6% reduction in FD relative to the original structure. Furthermore, the optimization results are validated through impedance tube experiments. The sequential optimization strategy provides an efficient solution for applications demanding both effective noise control and low flow drag.
- 1 February 2026
- Published by AIP Publishing in AIP Advances
- Vol. 16 (2)
Open AccessSequential optimization of spiral structures for simultaneous noise reduction and flow drag minimization
Spiral acoustic structures hold significant potential for noise suppression in fluid flow systems; however, their aerodynamic performance has often been overlooked in previous studies. To bridge this gap, the present study develops a sequential optimization strategy aimed at simultaneously maximizing acoustic transmission loss (TL) and minimizing flow drag (FD). The strategy integrates a multi-objective genetic algorithm with surrogate models for initial global exploration of the design space, followed by an adjoint optimization method for local refinement of the inner wall geometry. Under fixed outer dimensions, the spiral geometry is parameterized using inner diameter, spiral angular frequency, spiral position, and dimensionless pitch. Sensitivity analysis is employed to identify the key structural parameters. Surrogate models are constructed to efficiently map the structural parameters to FD and total transmission loss (TY), respectively. A multi-objective genetic algorithm identifies a multi-objective optimization structure achieving TY higher than 7 dB and reducing FD by 306.35 Pa at 10 m/s compared to the original structure. The adjoint optimization, building upon this multi-objective optimization structure result, further reduces the FD by an additional 89.33 Pa without compromising the TL. The sequential optimization strategy ultimately delivers a 23% increase in TY and a 53.6% reduction in FD relative to the original structure. Furthermore, the optimization results are validated through impedance tube experiments. The sequential optimization strategy provides an efficient solution for applications demanding both effective noise control and low flow drag.
- 1 January 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (1)
Flow velocity around air-conditioner outdoor unit
The time-averaged and fluctuating components of flow velocity have significant impacts on the heat exchange performance and noise level of an air-conditioner outdoor unit. This study uses a hot-wire measurement method to investigate the instantaneous velocity field around the outdoor unit. In comparison to the inlet flow field that exhibits a low and uniform average velocity, the outlet flow field displays a high average velocity but is uneven in the radial direction. Both periodic and stochastic components of the velocity disturbances are primarily located at blade tip. A deep neural network model is constructed and trained based on the experimental data, with the objective of mapping the steady flow quantities to the turbulence kinetic energy spectrum, and the results demonstrate that the relative prediction error is smaller than 5% with a probability of 92.49%.
- 1 January 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (1)
Flow velocity around air-conditioner outdoor unit
The time-averaged and fluctuating components of flow velocity have significant impacts on the heat exchange performance and noise level of an air-conditioner outdoor unit. This study uses a hot-wire measurement method to investigate the instantaneous velocity field around the outdoor unit. In comparison to the inlet flow field that exhibits a low and uniform average velocity, the outlet flow field displays a high average velocity but is uneven in the radial direction. Both periodic and stochastic components of the velocity disturbances are primarily located at blade tip. A deep neural network model is constructed and trained based on the experimental data, with the objective of mapping the steady flow quantities to the turbulence kinetic energy spectrum, and the results demonstrate that the relative prediction error is smaller than 5% with a probability of 92.49%.
- 8 February 2022
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 31 (3) , 035023
Numerical and experimental analysis on the helicopter rotor dynamic load controlled by the actively trailing edge flap
Reducing the rotor dynamic load is an important issue to improve the performance and reliability of a helicopter. The control mechanism of the actively controlled flap (ACF) on the rotor dynamic load is numerically and experimentally investigated by a 3-blade helicopter rotor in this paper. In the aero-elastic numerical approach, the complex motion of the rotor such as the stretching, bending, torsion and pitching of the blade including the deflection of the ACF are all taken into consideration in the structural formulation. The aerodynamic solution adopted the vortex lattice method combined with the free wake model, in which the influence of ACF on the free wake and the aerodynamic load on the blade is taken into account as well. While the experimental method of measuring hub loads and acoustic was accomplished by a rotor rig in a wind tunnel. The result shows that the 3/rev ACF actuation can reduce the 3 ω hub load by more than 50% at maximum, which is significantly better than the 4/rev control. While 4/rev has greater potential to reduce blade vortex interaction (BVI) loads than 3/rev with µ = 0.15. Further mechanistic analysis shows that by changing the phase difference between the dynamic load on the flap and the rest of the blade, the peak load on the whole blade can be improved, thus achieving effective control of the hub dynamic load, the flap reaches the minimum angle of attack at 90 ∘ –100 ∘ azimuth under best control condition; when the BVI load is perfectly controlled, the flap reaches the minimum angle of attack at 140 ∘ azimuth, and by changing the circulation of the wake, the intensity of BVI in the advancing side is improved. Moreover, an interesting finding in the optimal control of noise and vibration is that an overlap point exists on the motion patterns of the flap with different frequencies.
- 8 February 2022
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 31 (3) , 035023
Numerical and experimental analysis on the helicopter rotor dynamic load controlled by the actively trailing edge flap
Reducing the rotor dynamic load is an important issue to improve the performance and reliability of a helicopter. The control mechanism of the actively controlled flap (ACF) on the rotor dynamic load is numerically and experimentally investigated by a 3-blade helicopter rotor in this paper. In the aero-elastic numerical approach, the complex motion of the rotor such as the stretching, bending, torsion and pitching of the blade including the deflection of the ACF are all taken into consideration in the structural formulation. The aerodynamic solution adopted the vortex lattice method combined with the free wake model, in which the influence of ACF on the free wake and the aerodynamic load on the blade is taken into account as well. While the experimental method of measuring hub loads and acoustic was accomplished by a rotor rig in a wind tunnel. The result shows that the 3/rev ACF actuation can reduce the 3 ω hub load by more than 50% at maximum, which is significantly better than the 4/rev control. While 4/rev has greater potential to reduce blade vortex interaction (BVI) loads than 3/rev with µ = 0.15. Further mechanistic analysis shows that by changing the phase difference between the dynamic load on the flap and the rest of the blade, the peak load on the whole blade can be improved, thus achieving effective control of the hub dynamic load, the flap reaches the minimum angle of attack at 90 ∘ –100 ∘ azimuth under best control condition; when the BVI load is perfectly controlled, the flap reaches the minimum angle of attack at 140 ∘ azimuth, and by changing the circulation of the wake, the intensity of BVI in the advancing side is improved. Moreover, an interesting finding in the optimal control of noise and vibration is that an overlap point exists on the motion patterns of the flap with different frequencies.