Muhammad Ramzan Luhur
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Muhammad Ramzan Luhur has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
Liaquat Ali Memon
2 shared publicationsSaleem Raza Samo
2 shared publicationsAli Raza Solangi
1 shared publication- Aqeel Ahmed Bhutto
Department of Mechanical Engineering, Mehran University of Engineering and Technology, SZAB Campus, Khairpur Mirs 66020, Pakistan
1 shared publication - Faheem Ahmed Solangi
Quaid-e-Awam University of Engineering, Science and Technology Nawabshah, Sindh, Pakistan
1 shared publication - Faheem Ahmed Solangi
Department of Mechanical Engineering Science and Technology Quaid-e-Awam University of Engineering 67480 Sindh Pakistan
1 shared publication
Latest Publications
- Open Access
- 1 January 2025
- Published by Yildiz Technical University in Journal of Thermal Engineering
- Vol. 11 (3) , 727-739
Effect of higher alcohol on injector deposit and wear in compression ignition engine
An environmentally friendly and energy-secure approach is to recycle waste cooking oil (WCO) for use in diesel engines. In place of costly pre-heating and trans-esterification, diesel-WCO-alcohol ternary blends offer a simple and affordable way to use both a bio-component and a recycled component to substitute diesel and lower the viscosity of WCO partially. This investigation tested three fuel samples: 20% waste cooking oil, 65% DF, and 15% n-pentanol; diesel fuel, which served as the reference; and 5% waste cooking oil and 95% DF. The 200-hour endurance test was performed on the single-cylinder CI engine. An atomic absorption spectrophotometer equipped with hollow cathode lamps for every element was used to quantify the engine wear debris, and scanning electron microscopy and energy-dispersive X-ray spectroscopy procedures were employed to analyze the elements and measure deposit accumulations. Furthermore, temperatures at and around the injector tip caused by modern diesel injection systems may result in incredibly persistent deposits. After prolonged use, some fuels can damage the engine itself, generate excessive carbon and lacquer buildup, and make an engine operate less efficiently. The proportion of carbon layer on injector surfaces for DF, DF95WCO5, and DF65WCO20Pe15 is 32.54%, 56.17%, and 27.58%, respectively. In this experimental investigation, the fuel DF65WCO20Pe15 showed minimal injector deposit buildup.
- 1 January 2025
- Published by Yildiz Technical University in Journal of Thermal Engineering
- Vol. 11 (3) , 727-739
Open AccessEffect of higher alcohol on injector deposit and wear in compression ignition engine
An environmentally friendly and energy-secure approach is to recycle waste cooking oil (WCO) for use in diesel engines. In place of costly pre-heating and trans-esterification, diesel-WCO-alcohol ternary blends offer a simple and affordable way to use both a bio-component and a recycled component to substitute diesel and lower the viscosity of WCO partially. This investigation tested three fuel samples: 20% waste cooking oil, 65% DF, and 15% n-pentanol; diesel fuel, which served as the reference; and 5% waste cooking oil and 95% DF. The 200-hour endurance test was performed on the single-cylinder CI engine. An atomic absorption spectrophotometer equipped with hollow cathode lamps for every element was used to quantify the engine wear debris, and scanning electron microscopy and energy-dispersive X-ray spectroscopy procedures were employed to analyze the elements and measure deposit accumulations. Furthermore, temperatures at and around the injector tip caused by modern diesel injection systems may result in incredibly persistent deposits. After prolonged use, some fuels can damage the engine itself, generate excessive carbon and lacquer buildup, and make an engine operate less efficiently. The proportion of carbon layer on injector surfaces for DF, DF95WCO5, and DF65WCO20Pe15 is 32.54%, 56.17%, and 27.58%, respectively. In this experimental investigation, the fuel DF65WCO20Pe15 showed minimal injector deposit buildup.
- 2 June 2024
- Published by Penerbit UTM Press in Jurnal Teknologi (Sciences & Engineering)
- Vol. 86 (4) , 131-137
ANALYSIS OF LUBRICANT OIL DEGRADATION AND SOUND PRESSURE LEVEL FOR CI ENGINE USING BLEND FUELS
Long-term engine running has been the subject of extensive research on the deterioration of engine oil. In contrast, it is not fully clear what effect synthetic and biofuels will have. Modern engines, traditional fuels and lubricants should be used to provide a research basis for characterizing novel fuel-related phenomena in engines. This study makes an effort to characterize how lubricating engine oil behaves over the course of its service life using data on friction and wear. Every 20 hours, oil samples from the engine were obtained to evaluate its chemical makeup. On a reciprocating test rig, friction and wear measurements were taken. Kinematic viscosity, density, and wear metals such as cadmium (Cd), cobalt (Co), and lead (Pb) were measured for the lubricant oil analysis. In general, n-pentanol aids in the reduction of engine wear debris, contamination, and lubricating oil oxidation. According to the findings of this study, a D60WCO20Pe15 ternary combination can be used in a diesel engine without any alteration. The sound pressure level (SPL) increased by 7.8 dB at engine speed of 1300 RPM in the case of the DF95WCO5. However, when compared to base line, the average SPL of D60WCO20Pe15 ternary blend was 4.3 dB lower.
- 2 June 2024
- Published by Penerbit UTM Press in Jurnal Teknologi (Sciences & Engineering)
- Vol. 86 (4) , 131-137
ANALYSIS OF LUBRICANT OIL DEGRADATION AND SOUND PRESSURE LEVEL FOR CI ENGINE USING BLEND FUELS
Long-term engine running has been the subject of extensive research on the deterioration of engine oil. In contrast, it is not fully clear what effect synthetic and biofuels will have. Modern engines, traditional fuels and lubricants should be used to provide a research basis for characterizing novel fuel-related phenomena in engines. This study makes an effort to characterize how lubricating engine oil behaves over the course of its service life using data on friction and wear. Every 20 hours, oil samples from the engine were obtained to evaluate its chemical makeup. On a reciprocating test rig, friction and wear measurements were taken. Kinematic viscosity, density, and wear metals such as cadmium (Cd), cobalt (Co), and lead (Pb) were measured for the lubricant oil analysis. In general, n-pentanol aids in the reduction of engine wear debris, contamination, and lubricating oil oxidation. According to the findings of this study, a D60WCO20Pe15 ternary combination can be used in a diesel engine without any alteration. The sound pressure level (SPL) increased by 7.8 dB at engine speed of 1300 RPM in the case of the DF95WCO5. However, when compared to base line, the average SPL of D60WCO20Pe15 ternary blend was 4.3 dB lower.