Yunfei Du
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Yunfei Du has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Rui Bai
Department of Mechanical Engineering, Taiyuan Institute of Technology, Taiyuan 030008, China
3 shared publications - Xiuli He
Department of Mechanical Engineering, Taiyuan Institute of Technology, Taiyuan 030008, China
2 shared publications Bo Wang
National Key Laboratory of Integrated Circuits and Microsystems , Chongqing , 401332 , PR China
1 shared publicationGuodong Li
School of Mechanical Engineering, North University of China , Taiyuan , 030051 , PR China
1 shared publicationHongyu Liang
Department of Mechanical Engineering, Taiyuan Institute of Technology, Taiyuan 030008, China
1 shared publication- Li Zhang
School of Mechanical Engineering, North University of China , Taiyuan , 030051 , P.R. China
1 shared publication
Latest Publications
- Open Access
Achieving High Specific Strength via Multiple Strengthening Mechanisms in an Fe-Mn-Al-C-Ni-Cr Lightweight Steel
The development of lightweight steels with high specific strength is critical for automotive applications and energy savings. This study aimed to develop a high-performance lightweight steel with high specific strength by designing an alloy composition and optimizing thermomechanical processing. A novel Fe-28.6Mn-10.2Al-1.1C-3.2Ni-3.9Cr (wt.%) steel was investigated, focusing on microstructural evolution, mechanical properties, and strengthening mechanisms. The steel was processed through hot-rolling, solution treatment, cold-rolling, and subsequent annealing. Microstructural characterization revealed a dual-phase matrix of austenite and ferrite (6.8 vol.%), with B2 precipitates distributed at the grain boundaries and within the austenite matrix, alongside nanoscale κ-carbides (<10 nm). Short-time annealing resulted in the finer austenite grains (~1.1 μm) and the higher volume fraction (5.0%) of intragranular B2 precipitates with a smaller size (~0.18 μm), while long-time annealing promoted the coarsening of austenite grains (~1.6 μm) and the growth of intergranular B2 particles (~0.9 μm). This steel achieved yield strengths of 1130~1218 MPa and tensile strengths of 1360~1397 MPa through multiple strengthening mechanisms, including solid solution strengthening, grain boundary strengthening, dislocation strengthening, and precipitation strengthening.
Open AccessAchieving High Specific Strength via Multiple Strengthening Mechanisms in an Fe-Mn-Al-C-Ni-Cr Lightweight Steel
The development of lightweight steels with high specific strength is critical for automotive applications and energy savings. This study aimed to develop a high-performance lightweight steel with high specific strength by designing an alloy composition and optimizing thermomechanical processing. A novel Fe-28.6Mn-10.2Al-1.1C-3.2Ni-3.9Cr (wt.%) steel was investigated, focusing on microstructural evolution, mechanical properties, and strengthening mechanisms. The steel was processed through hot-rolling, solution treatment, cold-rolling, and subsequent annealing. Microstructural characterization revealed a dual-phase matrix of austenite and ferrite (6.8 vol.%), with B2 precipitates distributed at the grain boundaries and within the austenite matrix, alongside nanoscale κ-carbides (<10 nm). Short-time annealing resulted in the finer austenite grains (~1.1 μm) and the higher volume fraction (5.0%) of intragranular B2 precipitates with a smaller size (~0.18 μm), while long-time annealing promoted the coarsening of austenite grains (~1.6 μm) and the growth of intergranular B2 particles (~0.9 μm). This steel achieved yield strengths of 1130~1218 MPa and tensile strengths of 1360~1397 MPa through multiple strengthening mechanisms, including solid solution strengthening, grain boundary strengthening, dislocation strengthening, and precipitation strengthening.
- Open Access
Effect of Intercritical Quenching Temperature on Microstructure and Mechanical Performance of Cr-Ni-Mo-V Steel with Banded Structure
The effects of intercritical quenching on the microstructure evolution and mechanical performance of Cr–Ni–Mo–V steel with a banded structure are studied. It is found that the intercritical quenching temperature has a significant effect on the morphology, distribution, and relative amount of ferrite/martensite, as well as the carbide precipitates upon tempering treatment. It is indicated that owing to the initial banded structure of Cr-Ni-Mo-V steel, the ferrite formation in intercritical heat treatment also exhibits a banded distribution. With the increase in quenching temperature, the proportion of ferrite in the Cr-Ni-Mo-V steel decreases from 30 ± 3.2 vol.% to 18 ± 2.8 vol.%. Tempering treatment has no significant effect on the distribution characteristics of ferrite, but it promotes the recovery of martensite laths and the precipitation of carbides. The mechanical properties of Cr-Ni-Mo-V steel are determined by both the changes in ferrite content induced by intercritical quenching and the evolution of carbide types during tempering. Delamination cracks are observed on the fracture surface, which is attributed to the lamellar microstructure, improving the plasticity of Cr-Ni-Mo-V steel through stress dispersion and a multi-stage energy absorption mechanism.
Open AccessEffect of Intercritical Quenching Temperature on Microstructure and Mechanical Performance of Cr-Ni-Mo-V Steel with Banded Structure
The effects of intercritical quenching on the microstructure evolution and mechanical performance of Cr–Ni–Mo–V steel with a banded structure are studied. It is found that the intercritical quenching temperature has a significant effect on the morphology, distribution, and relative amount of ferrite/martensite, as well as the carbide precipitates upon tempering treatment. It is indicated that owing to the initial banded structure of Cr-Ni-Mo-V steel, the ferrite formation in intercritical heat treatment also exhibits a banded distribution. With the increase in quenching temperature, the proportion of ferrite in the Cr-Ni-Mo-V steel decreases from 30 ± 3.2 vol.% to 18 ± 2.8 vol.%. Tempering treatment has no significant effect on the distribution characteristics of ferrite, but it promotes the recovery of martensite laths and the precipitation of carbides. The mechanical properties of Cr-Ni-Mo-V steel are determined by both the changes in ferrite content induced by intercritical quenching and the evolution of carbide types during tempering. Delamination cracks are observed on the fracture surface, which is attributed to the lamellar microstructure, improving the plasticity of Cr-Ni-Mo-V steel through stress dispersion and a multi-stage energy absorption mechanism.
- Open Access
The Influence of Cr Addition on the Microstructure and Mechanical Properties of Fe-25Mn-10Al-1.2C Lightweight Steel
The influence of Cr addition on the microstructure and tensile properties of Fe-25Mn-10Al-1.2C lightweight steel was investigated. The characteristics of the microstructures and deformation behavior were carried out through X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), electron backscatter diffraction (EBSD), and room temperature tensile testing. Fe-20Mn-12Al-1.5C steel without Cr exhibited a fully austenitic single phase. With the addition of Cr, the volume fraction of ferrite continuously increased. When the content of Cr exceeded 5 wt%, the precipitation of Cr7C3 carbides was observed. In the steel with 5 wt% Cr, the quantity of κ carbides remarkably decreased, indicating that the addition of 5 wt% Cr significantly inhibited the nucleation of κ-carbides. As the Cr content increases from 0 wt% to 5 wt%, the austenite grain sizes were 8.8 μm and 2.5 μm, respectively, demonstrating that Cr alloying is an effective method of grain refinement. Tensile strength increased slightly while elongation decreased with increasing Cr content. As the Cr content exceeded 5 wt%, the yield strength increased but the elongation drastically decreased. The steel with 2.5 wt% Cr achieved a synergistic improvement in strength and ductility, exhibiting the best tensile performance.
Open AccessThe Influence of Cr Addition on the Microstructure and Mechanical Properties of Fe-25Mn-10Al-1.2C Lightweight Steel
The influence of Cr addition on the microstructure and tensile properties of Fe-25Mn-10Al-1.2C lightweight steel was investigated. The characteristics of the microstructures and deformation behavior were carried out through X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), electron backscatter diffraction (EBSD), and room temperature tensile testing. Fe-20Mn-12Al-1.5C steel without Cr exhibited a fully austenitic single phase. With the addition of Cr, the volume fraction of ferrite continuously increased. When the content of Cr exceeded 5 wt%, the precipitation of Cr7C3 carbides was observed. In the steel with 5 wt% Cr, the quantity of κ carbides remarkably decreased, indicating that the addition of 5 wt% Cr significantly inhibited the nucleation of κ-carbides. As the Cr content increases from 0 wt% to 5 wt%, the austenite grain sizes were 8.8 μm and 2.5 μm, respectively, demonstrating that Cr alloying is an effective method of grain refinement. Tensile strength increased slightly while elongation decreased with increasing Cr content. As the Cr content exceeded 5 wt%, the yield strength increased but the elongation drastically decreased. The steel with 2.5 wt% Cr achieved a synergistic improvement in strength and ductility, exhibiting the best tensile performance.
- Open Access
- 1 January 2024
- Published by Walter de Gruyter GmbH in High Temperature Materials and Processes
- Vol. 43 (1)
Hot deformation behaviors and microstructure characteristics of Cr–Mo–Ni–V steel with a banded structure
On a Gleeble-3800 thermal simulator, the hot deformation behavior of Cr–Mo–Ni–V steel was studied, with the designed deformation temperature varying from 900 to 1,200°C and the strain rate in the range of 0.01–10 s −1 . It was observed that as the strain rate was increased and the hot working temperature was reduced, the flow stress of the experimental steel increased. The study also evaluated the safe parameters for deformation of the Cr–Mo–Ni–V steel in the hot working process, based on the established processing maps. It was found that the deformation temperature window varying from 1,050 to 1,150°C and the reasonable strain rate in the range of 0.01–1 s −1 are beneficial to the hot deformation of the steel. In this research, the effect of processing parameters of the hot working process on the microstructure evolution of the banded structure was also investigated. According to the research result, the banded structure in the steel remained visible under the conditions of a strain rate of 10 s −1 and the hot working temperature in the range of 900–1,200°C. However, it should be noted that the banded structure in the steel then gradually disappeared when the hot working temperature was increased to 1,200°C.
- 1 January 2024
- Published by Walter de Gruyter GmbH in High Temperature Materials and Processes
- Vol. 43 (1)
Open AccessHot deformation behaviors and microstructure characteristics of Cr–Mo–Ni–V steel with a banded structure
On a Gleeble-3800 thermal simulator, the hot deformation behavior of Cr–Mo–Ni–V steel was studied, with the designed deformation temperature varying from 900 to 1,200°C and the strain rate in the range of 0.01–10 s −1 . It was observed that as the strain rate was increased and the hot working temperature was reduced, the flow stress of the experimental steel increased. The study also evaluated the safe parameters for deformation of the Cr–Mo–Ni–V steel in the hot working process, based on the established processing maps. It was found that the deformation temperature window varying from 1,050 to 1,150°C and the reasonable strain rate in the range of 0.01–1 s −1 are beneficial to the hot deformation of the steel. In this research, the effect of processing parameters of the hot working process on the microstructure evolution of the banded structure was also investigated. According to the research result, the banded structure in the steel remained visible under the conditions of a strain rate of 10 s −1 and the hot working temperature in the range of 900–1,200°C. However, it should be noted that the banded structure in the steel then gradually disappeared when the hot working temperature was increased to 1,200°C.