Iñigo Rodriguez Bogajo
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Iñigo Rodriguez Bogajo has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Pedro Jose Arrazola
Mondragon Unibertsitatea
2 shared publications Chanyapan Virulsri
Center of Excellence for Prosthetic and Orthopedic Implant, Department of Mechanical Engineering, Faculty of Engineering, Chulalongkorn University, Bangkok, Thailand
1 shared publication- Franci Pusavec
Faculty of Mechanical Engineering, University of Ljubljana, Ljubljana, Slovenia
1 shared publication - Gorka Ortiz-De-Zarate
Mondragon Unibertsitatea
1 shared publication - Mikel Etxebeste
Mondragon Unibertsitatea
1 shared publication Pairat Tangpronprasert
Center of Excellence for Prosthetic and Orthopedic Implant, Department of Mechanical Engineering, Faculty of Engineering, Chulalongkorn University, Bangkok, Thailand
1 shared publication
Latest Publications
- Open Access
- 13 November 2026
- Published by Elsevier in SSRN Electronic Journal
A Framework for Cutting Tool Reconditioning: Integrating Quality Assurance, Remaining Useful Life and Sustainability
Cutting tool reconditioning enhances Critical Raw Material (CRM) efficiency (e.g. tungsten and cobalt) in machining, yet its industrial adoption is stalled by the absence of standardised methods to certify reconditioning quality and predict Remaining Useful Life (RUL). This paper moves towards standardised reconditioning certification by establishing a novel framework that integrates nondestructive and destructive inspection for reconditioning quality assurance, RUL quantification, and Life Cycle Assessment (LCA) to evaluate circular tool management strategies. The framework is transferable wherever tool embodied energy, reconditioning process data, and the tool life ratio of reconditioned versus new tools are known. It was validated on a 316L stainless steel milling case study using uncoated carbide end mills, comparing three end-of-life scenarios: (i) linear replacement; (ii) resharpening alone; and (iii) resharpening with subsequent edge honing. Resharpening alone reduced tool life by 25% relative to new tools, primarily because it decreased the cutting edge radius from 8 µm to 4 µm, producing sharper but more brittle edges susceptible to micro-chipping. Notably, Scanning Electron Microscope (SEM) inspection validated that resharpening eliminated the wearaffected volume, confirming that this tool life reduction is geometric rather than microstructural in origin. Edge honing restored the original geometry and recovered tool life to new-tool baseline levels. Cradle-to-grave LCA revealed that resharpening alone reduced cost and CO₂ footprint by 47% and 50%, respectively. Resharpening with honing achieved greater reductions (57% and 60%) despite an additional process step, as the end mills showed greater tool life. Both reconditioning scenarios reached economic break-even with linear replacement at the first tool replacement cycle.
- 13 November 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessA Framework for Cutting Tool Reconditioning: Integrating Quality Assurance, Remaining Useful Life and Sustainability
Cutting tool reconditioning enhances Critical Raw Material (CRM) efficiency (e.g. tungsten and cobalt) in machining, yet its industrial adoption is stalled by the absence of standardised methods to certify reconditioning quality and predict Remaining Useful Life (RUL). This paper moves towards standardised reconditioning certification by establishing a novel framework that integrates nondestructive and destructive inspection for reconditioning quality assurance, RUL quantification, and Life Cycle Assessment (LCA) to evaluate circular tool management strategies. The framework is transferable wherever tool embodied energy, reconditioning process data, and the tool life ratio of reconditioned versus new tools are known. It was validated on a 316L stainless steel milling case study using uncoated carbide end mills, comparing three end-of-life scenarios: (i) linear replacement; (ii) resharpening alone; and (iii) resharpening with subsequent edge honing. Resharpening alone reduced tool life by 25% relative to new tools, primarily because it decreased the cutting edge radius from 8 µm to 4 µm, producing sharper but more brittle edges susceptible to micro-chipping. Notably, Scanning Electron Microscope (SEM) inspection validated that resharpening eliminated the wearaffected volume, confirming that this tool life reduction is geometric rather than microstructural in origin. Edge honing restored the original geometry and recovered tool life to new-tool baseline levels. Cradle-to-grave LCA revealed that resharpening alone reduced cost and CO₂ footprint by 47% and 50%, respectively. Resharpening with honing achieved greater reductions (57% and 60%) despite an additional process step, as the end mills showed greater tool life. Both reconditioning scenarios reached economic break-even with linear replacement at the first tool replacement cycle.
- Open Access
- 2 June 2024
- Published by Elsevier in CIRP Annals
- Vol. 73 (1) , 77-80
The impact of airborne emissions from coolants and lubricants on machining costs
- 2 June 2024
- Published by Elsevier in CIRP Annals
- Vol. 73 (1) , 77-80
Open AccessThe impact of airborne emissions from coolants and lubricants on machining costs
- 1 December 2020
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 111 (7-8) , 1971-1989
A novel indirect cryogenic cooling system for improving surface finish and reducing cutting forces when turning ASTM F-1537 cobalt-chromium alloys
- 1 December 2020
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 111 (7-8) , 1971-1989
A novel indirect cryogenic cooling system for improving surface finish and reducing cutting forces when turning ASTM F-1537 cobalt-chromium alloys