Jian Zhao
Jian Zhao has a total of 27 co-authors. Here are the top co-authors by number of shared publications:
- Jikang Yan
School of New Energy and Materials, Southwest Petroleum University, Chengdu, China
3 shared publications Biao Wang
2 shared publicationsJianhua Zhao
2 shared publicationsSenlin Yi
2 shared publications- Bensheng Huang
School of New Energy and Materials, Southwest Petroleum University, Chengdu, People’s Republic of China
1 shared publication Fang Li
1 shared publication
Latest Publications
- Open Access
- 26 May 2026
- Published by Elsevier in SSRN Electronic Journal
Influence of Sb/Bi Alloying on the Crystallographic Orientation and Mechanical Stability of Cu-Sn Intermetallic Compounds
In this study, the Sb- and Bi-alloyed Sn-Cu systems were investigated. By integrating sublattice modeling, Rietveld refinement, EBSD technique, and nanoindentation tests, the regulatory mechanisms of alloying on the crystal structure, texture evolution, and mechanical behavior of intermetallic compounds (IMCs) were systematically explored. Phase evolution at various temperatures was calculated based on the CALPHAD method. In the Sn-Cu system, the η'-Cu6Sn5, η-Cu6Sn5, and Cu3Sn phases exhibit distinct crystal structures and atomic site occupancy characteristics. At elevated temperatures, the vacancies in η-Cu6Sn5 provide essential pathways for atomic diffusion. The addition of Sb and Bi increased the liquid phase volume fraction during the sintering process, effectively enhancing the microstructural uniformity. The Sb- and Bi-alloyed intermetallic compounds were fabricated via powder metallurgy (PM). Subsequently, the influence of alloying on crystallographic orientation was characterized and analyzed through Rietveld refinement and EBSD techniques. In the Sn-39.1Cu alloy, the η'-Cu6Sn5 grains exhibit a preferred orientation predominantly along the (010) and (001) directions. Following the addition of Sb, the crystallographic orientation of η'-Cu6Sn5 tends to become randomized, which significantly mitigates/weakens the micro-anisotropy of the material. The η-Cu6Sn5 phase exhibits orientation-dependent variations at different locations. Nanoindentation characterization reveals disparities in the mechanical properties of the alloy; specifically, the pop-in phenomenon observed in η'-Cu6Sn5 is attributed to dislocation nucleation and pile-up. Furthermore, Bi-alloying reduces the steady-state creep rate, effectively enhancing the creep resistance of the material, which contributes positively to the long-term service reliability of solder joints.
- 26 May 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessInfluence of Sb/Bi Alloying on the Crystallographic Orientation and Mechanical Stability of Cu-Sn Intermetallic Compounds
In this study, the Sb- and Bi-alloyed Sn-Cu systems were investigated. By integrating sublattice modeling, Rietveld refinement, EBSD technique, and nanoindentation tests, the regulatory mechanisms of alloying on the crystal structure, texture evolution, and mechanical behavior of intermetallic compounds (IMCs) were systematically explored. Phase evolution at various temperatures was calculated based on the CALPHAD method. In the Sn-Cu system, the η'-Cu6Sn5, η-Cu6Sn5, and Cu3Sn phases exhibit distinct crystal structures and atomic site occupancy characteristics. At elevated temperatures, the vacancies in η-Cu6Sn5 provide essential pathways for atomic diffusion. The addition of Sb and Bi increased the liquid phase volume fraction during the sintering process, effectively enhancing the microstructural uniformity. The Sb- and Bi-alloyed intermetallic compounds were fabricated via powder metallurgy (PM). Subsequently, the influence of alloying on crystallographic orientation was characterized and analyzed through Rietveld refinement and EBSD techniques. In the Sn-39.1Cu alloy, the η'-Cu6Sn5 grains exhibit a preferred orientation predominantly along the (010) and (001) directions. Following the addition of Sb, the crystallographic orientation of η'-Cu6Sn5 tends to become randomized, which significantly mitigates/weakens the micro-anisotropy of the material. The η-Cu6Sn5 phase exhibits orientation-dependent variations at different locations. Nanoindentation characterization reveals disparities in the mechanical properties of the alloy; specifically, the pop-in phenomenon observed in η'-Cu6Sn5 is attributed to dislocation nucleation and pile-up. Furthermore, Bi-alloying reduces the steady-state creep rate, effectively enhancing the creep resistance of the material, which contributes positively to the long-term service reliability of solder joints.
- 31 May 2024
- Published by Elsevier in Physica B: Condensed Matter
- Vol. 690
Effects of Zn contents and doping positions on the mechanical properties of η′-Cu6Sn5
- 31 May 2024
- Published by Elsevier in Physica B: Condensed Matter
- Vol. 690
Effects of Zn contents and doping positions on the mechanical properties of η′-Cu6Sn5