Zdenko Tonković
Research Subjects
Zdenko Tonković has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Ante Bubalo
Yazaki Europe Limited, Slavonska 26/6, HR-10000 Zagreb, Croatia
1 shared publication - Lovre Krstulović-Opara
Faculty of Electrical Engineering, Mechanical Engineering and Naval Architecture, University of Split, 21000 Split, Croatia
1 shared publication - Tomislav Lesičar
University of Zagreb
1 shared publication - Tomislav Polančec
Laboratory of Numerical Mechanics, Faculty of Mechanical Engineering and Naval Architecture, Ivana Lučića 5, 10000 Zagreb, Croatia
1 shared publication - Vedrana Cvitanić
Faculty of Electrical Engineering, Mechanical Engineering and Naval Architecture, University of Split, R. Boškovića 32, HR-21000 Split, Croatia
1 shared publication
Latest Publications
- Open Access
The Determination of the Elastoplastic and Phase-Field Parameters for Monotonic and Fatigue Fracture of Sintered Steel Astaloy™ Mo+0.2C
This paper presents a procedure for determining the elastoplastic parameters of phase-field fracture of sintered material. The material considered was sintered steel Astaloy™ Mo+0.2C of three densities: 6.5, 6.8 and 7.1 g/. The stress–strain curve and Wöhler curve, which are experimentally obtained, are utilized for validation of the numerical simulations. For modelling of damage evolution, a CCPF (Convergence check phase-field) algorithm was used as a numerical framework. During calibration of the numerical parameters, two-dimensional as well as three-dimensional modelling was used. A comparison of different fatigue degradation functions known from the literature is also made. To improve the efficiency of numerical simulations of fatigue behaviour, the cycle skip technique is also employed.Open AccessThe Determination of the Elastoplastic and Phase-Field Parameters for Monotonic and Fatigue Fracture of Sintered Steel Astaloy™ Mo+0.2C
This paper presents a procedure for determining the elastoplastic parameters of phase-field fracture of sintered material. The material considered was sintered steel Astaloy™ Mo+0.2C of three densities: 6.5, 6.8 and 7.1 g/. The stress–strain curve and Wöhler curve, which are experimentally obtained, are utilized for validation of the numerical simulations. For modelling of damage evolution, a CCPF (Convergence check phase-field) algorithm was used as a numerical framework. During calibration of the numerical parameters, two-dimensional as well as three-dimensional modelling was used. A comparison of different fatigue degradation functions known from the literature is also made. To improve the efficiency of numerical simulations of fatigue behaviour, the cycle skip technique is also employed. - Open Access
Experimental Investigation of Strain Rate Influence on Anisotropy of Uniaxial Tensile Mechanical Properties of CuFe2P Alloy Sheet
Wire crimping, a process commonly used in the automotive industry, is a solderless method for establishing electrical and mechanical connections between wire strands and terminals. The complexity of predicting the final shape of a crimped terminal and the imperative to minimize production costs indicate the use of advanced numerical methods. Such an approach requires a reliable phenomenological elasto-plastic constitutive model in which material behavior during the forming process is described. Copper alloy sheets, known for their ductility and strength, are commonly selected as terminal materials. Generally, sheet metals exhibit significant anisotropy in mechanical properties, and this phenomenon has not been sufficiently investigated experimentally for copper alloy sheets. Furthermore, the wire crimping process is conducted at higher velocities; therefore, the influence of the strain rate on the terminal material behavior has to be known. In this paper, the influence of the strain rate on the anisotropic elasto-plastic behavior of the copper alloy sheet CuFe2P is experimentally investigated. Tensile tests with strain rates of 0.0002 s−1, 0.2 s−1, 1 s−1, and 5.65 s−1 were conducted on sheet specimens with orientations of 0°, 45°, and 90° to the rolling direction. The influence of the strain rate on the orientation dependences of the stress–strain curve, elastic modulus, tensile strength, elongation, and Lankford coefficient was determined. Furthermore, the breaking angle at fracture and the inelastic heat fraction were determined for each considered specimen orientation. The considered experimental data were obtained by capturing the loading process using infrared thermography and digital image correlation techniques.
Open AccessExperimental Investigation of Strain Rate Influence on Anisotropy of Uniaxial Tensile Mechanical Properties of CuFe2P Alloy Sheet
Wire crimping, a process commonly used in the automotive industry, is a solderless method for establishing electrical and mechanical connections between wire strands and terminals. The complexity of predicting the final shape of a crimped terminal and the imperative to minimize production costs indicate the use of advanced numerical methods. Such an approach requires a reliable phenomenological elasto-plastic constitutive model in which material behavior during the forming process is described. Copper alloy sheets, known for their ductility and strength, are commonly selected as terminal materials. Generally, sheet metals exhibit significant anisotropy in mechanical properties, and this phenomenon has not been sufficiently investigated experimentally for copper alloy sheets. Furthermore, the wire crimping process is conducted at higher velocities; therefore, the influence of the strain rate on the terminal material behavior has to be known. In this paper, the influence of the strain rate on the anisotropic elasto-plastic behavior of the copper alloy sheet CuFe2P is experimentally investigated. Tensile tests with strain rates of 0.0002 s−1, 0.2 s−1, 1 s−1, and 5.65 s−1 were conducted on sheet specimens with orientations of 0°, 45°, and 90° to the rolling direction. The influence of the strain rate on the orientation dependences of the stress–strain curve, elastic modulus, tensile strength, elongation, and Lankford coefficient was determined. Furthermore, the breaking angle at fracture and the inelastic heat fraction were determined for each considered specimen orientation. The considered experimental data were obtained by capturing the loading process using infrared thermography and digital image correlation techniques.