Alemu Merga Iticha
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Alemu Merga Iticha has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
Bonsa Regassa Hunde
2 shared publicationsAbraham Debebe Woldeyohannes
1 shared publicationAmanuel Regassa Hunde
1 shared publication- Bonsa Regassa Hunde
Aerospace Engineering and Communication Satellite Department Space Science and Geospatial Institute Addis Ababa Ethiopia
1 shared publication Chala Regassa Hunde
1 shared publication- Dagim Asegid Tirfe
Centre of Armament and High Energy Materials, Institute of Research and Development, Ethiopian Defence University, Bishoftu, Hora Lake Bishoftu, 1041, Ethiopia
1 shared publication
Latest Publications
- Open Access
- 21 August 2026
- Published by Elsevier in Results in Materials
- Vol. 31
A review of recent advances in prosthetic socket fabrication: Integration of 3D printing and machine learning optimization
- 21 August 2026
- Published by Elsevier in Results in Materials
- Vol. 31
Open AccessA review of recent advances in prosthetic socket fabrication: Integration of 3D printing and machine learning optimization
- Open Access
- 5 June 2026
- Published by Elsevier in Next Materials
- Vol. 12
Numerical analysis of flow parameters for perovskite layer printing with a slot-die head integrated 3D printer
- 5 June 2026
- Published by Elsevier in Next Materials
- Vol. 12
Open AccessNumerical analysis of flow parameters for perovskite layer printing with a slot-die head integrated 3D printer
- Open Access
- 1 January 2026
- Published by Wiley in Modelling and Simulation in Engineering
- Vol. 2026 (1)
Performance Analysis of Regular (n–i–p) and Inverted (p–i–n) Perovskite Solar Cells Using SCAPS‐1D: A Comparative Study Based on Fabrication Parameters
Although perovskite solar cells hold significant promise for next‐generation photovoltaic technologies, their development is hindered by challenges such as nonradiative recombination losses, limited scalability, and long‐term stability. To better understand the influence of device architecture and key fabrication parameters on photovoltaic performance, this study models and analyzes two widely adopted PSC structures—the inverted planar p–i–n and conventional n–i–p architectures—using the Solar Cell Capacitance Simulation One‐Dimensional (SCAPS‐1D) software. The effects of electron transport layer (ETL), hole transport layer (HTL), and perovskite layer thicknesses, as well as perovskite layer defect density, on the key photovoltaic parameters were systematically investigated. The results reveal that increasing the perovskite layer thickness and reducing defect density significantly improve the power conversion efficiency (PCE) of both structures. The p–i–n architecture achieved a higher PCE of 22.52% because of its improved fill factor (FF), whereas the n–i–p structure exhibited higher open‐circuit voltage (Voc) and short‐circuit current density (Jsc), resulting in a PCE of 21.07%. Reducing the defect density from 1E+16 (cm −3 ) to 1E+12 (cm −3 ) and increasing perovskite layer thickness from 500 nm to 800 nm increased the maximum PCE to 26.88% for the regular n–i–p PSC and 28.22% for the inverted p–i–n PSC. Overall, based on the theoretical analysis and comparison with experimental results reported by other researchers, the inverted p–i–n architecture emerges as a promising candidate because of its superior efficiency, lower hysteresis, and fabrication simplicity, although the selection of an effective HTL remains a significant challenge. These findings provide valuable insights for the design and optimization of efficient PSCs.
- 1 January 2026
- Published by Wiley in Modelling and Simulation in Engineering
- Vol. 2026 (1)
Open AccessPerformance Analysis of Regular (n–i–p) and Inverted (p–i–n) Perovskite Solar Cells Using SCAPS‐1D: A Comparative Study Based on Fabrication Parameters
Although perovskite solar cells hold significant promise for next‐generation photovoltaic technologies, their development is hindered by challenges such as nonradiative recombination losses, limited scalability, and long‐term stability. To better understand the influence of device architecture and key fabrication parameters on photovoltaic performance, this study models and analyzes two widely adopted PSC structures—the inverted planar p–i–n and conventional n–i–p architectures—using the Solar Cell Capacitance Simulation One‐Dimensional (SCAPS‐1D) software. The effects of electron transport layer (ETL), hole transport layer (HTL), and perovskite layer thicknesses, as well as perovskite layer defect density, on the key photovoltaic parameters were systematically investigated. The results reveal that increasing the perovskite layer thickness and reducing defect density significantly improve the power conversion efficiency (PCE) of both structures. The p–i–n architecture achieved a higher PCE of 22.52% because of its improved fill factor (FF), whereas the n–i–p structure exhibited higher open‐circuit voltage (Voc) and short‐circuit current density (Jsc), resulting in a PCE of 21.07%. Reducing the defect density from 1E+16 (cm −3 ) to 1E+12 (cm −3 ) and increasing perovskite layer thickness from 500 nm to 800 nm increased the maximum PCE to 26.88% for the regular n–i–p PSC and 28.22% for the inverted p–i–n PSC. Overall, based on the theoretical analysis and comparison with experimental results reported by other researchers, the inverted p–i–n architecture emerges as a promising candidate because of its superior efficiency, lower hysteresis, and fabrication simplicity, although the selection of an effective HTL remains a significant challenge. These findings provide valuable insights for the design and optimization of efficient PSCs.
- 1 May 2025
- Published by Bentham Science Publishers Ltd. in Recent Patents on Engineering
- Vol. 19 (4) , 1-14
Numerical Simulation of Temperature Distribution and Residual Stress in Laser Beam Welding AA6061 and Ti-6Al-4V and Optimization of Welding Processes
Background: Since the combination of its rapid processing speed and high energy input, laser beam welding is considered advanced and suitable for welding thin and lightweight metals. The residual stresses deposited in the parts as a result of rapid heating and cooling render laserwelded components susceptible to fractures and deformities. Objective: In this patent, the modelling of the laser beam welding process during the joining of Ti- 6Al-4V and AA6061 dissimilar metals to analyze the effects of the welding process on residual stress and elastic strain by considering beam radius, beam offset, welding speed, and beam power as input parameters. Methods: The 3D model of the Ti-6Al-4V and AA6061 was developed using CATIA V5R16 software and beam radius. Beam offset, welding speed, and beam power are the input parameters considered, and the output parameters are stress and elastic strain. Design Expert is used to design the experiment. ANOVA was used, and a mathematical model was developed to analyze the performance characteristics of the welding process. Results: The results revealed that increasing the laser power increases residual stress, whereas it decreases with increasing the other parameters. The maximum average equivalent von Mises stress was 288.79 MPa, which is near the yield strength of AA6061. The optimum welding conditions selected for minimum possible residual stress is 1600.003 W, welding speed 0.05 m/s, beam radius 0.014 m. Conclusion: Based on the current observation during the simulation of joining dissimilar metals, the flow temperature along the weld line and weldment shows uneven distribution due to the dissimilarity of temperature-dependent properties of materials. The increased laser power leads to an increase in residual stress.
- 1 May 2025
- Published by Bentham Science Publishers Ltd. in Recent Patents on Engineering
- Vol. 19 (4) , 1-14
Numerical Simulation of Temperature Distribution and Residual Stress in Laser Beam Welding AA6061 and Ti-6Al-4V and Optimization of Welding Processes
Background: Since the combination of its rapid processing speed and high energy input, laser beam welding is considered advanced and suitable for welding thin and lightweight metals. The residual stresses deposited in the parts as a result of rapid heating and cooling render laserwelded components susceptible to fractures and deformities. Objective: In this patent, the modelling of the laser beam welding process during the joining of Ti- 6Al-4V and AA6061 dissimilar metals to analyze the effects of the welding process on residual stress and elastic strain by considering beam radius, beam offset, welding speed, and beam power as input parameters. Methods: The 3D model of the Ti-6Al-4V and AA6061 was developed using CATIA V5R16 software and beam radius. Beam offset, welding speed, and beam power are the input parameters considered, and the output parameters are stress and elastic strain. Design Expert is used to design the experiment. ANOVA was used, and a mathematical model was developed to analyze the performance characteristics of the welding process. Results: The results revealed that increasing the laser power increases residual stress, whereas it decreases with increasing the other parameters. The maximum average equivalent von Mises stress was 288.79 MPa, which is near the yield strength of AA6061. The optimum welding conditions selected for minimum possible residual stress is 1600.003 W, welding speed 0.05 m/s, beam radius 0.014 m. Conclusion: Based on the current observation during the simulation of joining dissimilar metals, the flow temperature along the weld line and weldment shows uneven distribution due to the dissimilarity of temperature-dependent properties of materials. The increased laser power leads to an increase in residual stress.