Jun-Mo Kim
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Jun-Mo Kim has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
Byoung-Woo Yum
Korea Inst Geosci & Mineral Resources, Geol Environm Res Div, Daejeon 34132, South Korea
2 shared publications- Jung-Hwi Kihm
Department of Fire Protection and Safety Management, Jungwon University, Goesan-Gun, Republic of Korea
2 shared publications Gour-Tsyh Yeh
Ph.D. Student, School of Earth and Environmental Sciences, Seoul National Univ., Seoul 151-742, Republic of Korea
1 shared publication- Gour‐Tsyh Yeh
Graduate Institute of Applied Geology National Central University Taoyuan Taiwan
1 shared publication Jai-Yong Park
Seoul Natl Univ, Sch Earth & Environm Sci, Seoul 08826, South Korea
1 shared publicationJung‐Hwi Kihm
School of Earth and Environmental Sciences, Seoul National University, Seoul, South Korea
1 shared publication
Latest Publications
- 20 February 2025
- Published by Springer Nature in Environmental Earth Sciences
- Vol. 84 (5) , 1-34
Hydro-mechanical numerical evaluation of rainfall-induced fully coupled groundwater flow, land deformation, and failure potential in a variably saturated heterogeneous hill slope with consideration of interlinked rainfall-infiltration-seepage processes
- 20 February 2025
- Published by Springer Nature in Environmental Earth Sciences
- Vol. 84 (5) , 1-34
Hydro-mechanical numerical evaluation of rainfall-induced fully coupled groundwater flow, land deformation, and failure potential in a variably saturated heterogeneous hill slope with consideration of interlinked rainfall-infiltration-seepage processes
- Open Access
- 17 June 2024
- Published by American Geophysical Union (AGU) in Water Resources Research
- Vol. 60 (6)
Hydrogeologic Framework Model‐Based Numerical Simulation of Groundwater Flow and Salt Transport and Analytic Hierarchy Process‐Based Multi‐Criteria Evaluation of Optimal Pumping Location and Rate for Mitigation of Seawater Intrusion in a Complex Coastal Aquifer System
A series of hydrogeologic framework model (HFM)‐based steady‐ and transient‐state numerical simulations is performed first using a coupled subsurface flow‐transport numerical model to analyze groundwater flow and salt transport in an actual three‐dimensional complex coastal aquifer system before and during groundwater pumping. A series of analytic hierarchy process (AHP)‐based multi‐criteria evaluations is then performed applying a multi‐criteria decision‐making approach to determine optimal pumping location and rate for a new pumping well in the complex coastal aquifer system during groundwater pumping. The complex coastal aquifer system is composed of six anisotropic fractured porous geologic media (five rock formations and one fault) and three isotropic porous geologic media (three soil formations) and shows high geometric irregularity and significant heterogeneity and anisotropy of the nine geologic media. Results of the steady‐state numerical simulations show successful model calibration with 26 measured groundwater levels and two observed seawater intrusion front lines. The latter two are determined by spatial interpolation and extrapolation of electrical conductivity logging data and electrical resistivity survey data, respectively. Based on the status and prospect of necessary water uses and available groundwater resources, the field observations of groundwater and seawater intrusion, and the analyses of the steady‐state numerical simulation after the model calibration, six candidate pumping locations are selected for the new pumping well. In addition, from six preliminary individual transient‐state numerical simulations, maximum pumping rates at the six candidate pumping locations are calculated first, and a set of six incremental candidate pumping rates is then assigned at each of the six candidate pumping locations. Results of the transients‐state numerical simulations show that groundwater flow and salt transport are spatially and temporally changed, and seawater intrusion is further intensified by groundwater pumping. In addition, the magnitudes of such spatial and temporal changes and intensification are significantly different depending on the candidate pumping locations and rates. Results of the steady‐ and transient‐state numerical simulations also show that both complexity (geometric irregularity, heterogeneity, and anisotropy including the fault) and topography have significant effects on the spatial distributions and temporal changes of groundwater flow and salt transport in the coastal aquifer system before and during groundwater pumping. In addition, results of statistical estimations of the mesh Peclet and Courant numbers confirm acceptabilities of minimizing numerical dispersion in the steady‐ and transient‐state numerical simulations. Based on the analyses of the transient‐state numerical simulations, eight multiple criteria are chosen to judge, prioritize, and rank the six candidate pumping locations and six candidate pumping rates for optimal pumping. Results of the multi‐criteria evaluations determine the optimal pumping location and rate for the new pumping well among the six candidate pumping locations and six candidate pumping rates. In addition, results of consistency checks confirm consistencies of judgments in the multi‐criteria evaluations.
- 17 June 2024
- Published by American Geophysical Union (AGU) in Water Resources Research
- Vol. 60 (6)
Open AccessHydrogeologic Framework Model‐Based Numerical Simulation of Groundwater Flow and Salt Transport and Analytic Hierarchy Process‐Based Multi‐Criteria Evaluation of Optimal Pumping Location and Rate for Mitigation of Seawater Intrusion in a Complex Coastal Aquifer System
A series of hydrogeologic framework model (HFM)‐based steady‐ and transient‐state numerical simulations is performed first using a coupled subsurface flow‐transport numerical model to analyze groundwater flow and salt transport in an actual three‐dimensional complex coastal aquifer system before and during groundwater pumping. A series of analytic hierarchy process (AHP)‐based multi‐criteria evaluations is then performed applying a multi‐criteria decision‐making approach to determine optimal pumping location and rate for a new pumping well in the complex coastal aquifer system during groundwater pumping. The complex coastal aquifer system is composed of six anisotropic fractured porous geologic media (five rock formations and one fault) and three isotropic porous geologic media (three soil formations) and shows high geometric irregularity and significant heterogeneity and anisotropy of the nine geologic media. Results of the steady‐state numerical simulations show successful model calibration with 26 measured groundwater levels and two observed seawater intrusion front lines. The latter two are determined by spatial interpolation and extrapolation of electrical conductivity logging data and electrical resistivity survey data, respectively. Based on the status and prospect of necessary water uses and available groundwater resources, the field observations of groundwater and seawater intrusion, and the analyses of the steady‐state numerical simulation after the model calibration, six candidate pumping locations are selected for the new pumping well. In addition, from six preliminary individual transient‐state numerical simulations, maximum pumping rates at the six candidate pumping locations are calculated first, and a set of six incremental candidate pumping rates is then assigned at each of the six candidate pumping locations. Results of the transients‐state numerical simulations show that groundwater flow and salt transport are spatially and temporally changed, and seawater intrusion is further intensified by groundwater pumping. In addition, the magnitudes of such spatial and temporal changes and intensification are significantly different depending on the candidate pumping locations and rates. Results of the steady‐ and transient‐state numerical simulations also show that both complexity (geometric irregularity, heterogeneity, and anisotropy including the fault) and topography have significant effects on the spatial distributions and temporal changes of groundwater flow and salt transport in the coastal aquifer system before and during groundwater pumping. In addition, results of statistical estimations of the mesh Peclet and Courant numbers confirm acceptabilities of minimizing numerical dispersion in the steady‐ and transient‐state numerical simulations. Based on the analyses of the transient‐state numerical simulations, eight multiple criteria are chosen to judge, prioritize, and rank the six candidate pumping locations and six candidate pumping rates for optimal pumping. Results of the multi‐criteria evaluations determine the optimal pumping location and rate for the new pumping well among the six candidate pumping locations and six candidate pumping rates. In addition, results of consistency checks confirm consistencies of judgments in the multi‐criteria evaluations.
- 12 June 2012
- Published by American Geophysical Union (AGU) in Journal of Geophysical Research
- Vol. 117 (B6)
Hydrogeochemical numerical simulation of impacts of mineralogical compositions and convective fluid flow on trapping mechanisms and efficiency of carbon dioxide injected into deep saline sandstone aquifers
A series of numerical simulations, which consider density‐dependent (convective) groundwater and carbon dioxide (CO2) flow, is performed using a multiphase hydrogeochemical reactive transport numerical model to evaluate impacts of mineralogical compositions on the trapping mechanisms and efficiency of CO2 injected into a deep saline sandstone aquifer (reservoir rock). The results of the numerical simulations show that the mineralogical compositions of the sandstone aquifer have significant impacts on hydrogeochemical behavior of injected CO2 and thus its trapping mechanisms and efficiency. Injected CO2 is accumulated as a free fluid phase beneath the caprock (i.e., hydrodynamic trapping), then dissolved as aqueous phases such as bicarbonate and carbonate anions into groundwater (i.e., solubility trapping), and finally precipitated as carbonate minerals (i.e., mineral trapping). Mineral trapping of injected CO2 takes places as precipitation of a primary carbonate mineral such as calcite and secondary carbonate minerals such as dawsonite, siderite, ankerite, and magnesite. The patterns of hydrogeochemical reactions depend significantly on the initial presence and absence of chlorite in the sandstone aquifer. For mineral trapping of injected CO2, ankerite is the most dominant mineral when chlorite is initially present, whereas dawsonite is the most dominant mineral when chlorite is initially absent in the sandstone aquifer. Mg2+ and Fe2+, which are essential chemical components of such secondary carbonate minerals (i.e., siderite, ankerite, and magnesite) for mineral trapping of injected CO2, are mainly supplied by dissolution of chlorite. As a result, the precipitation amounts of the secondary carbonate minerals and thus the efficiency of mineral trapping of injected CO2 increase significantly as the volume fraction of chlorite increases in the sandstone aquifer. A series of additional numerical simulations, which consider density‐independent (non‐convective) multiphase fluid flow, is also performed using the same numerical model, and then its results are compared with those of the above‐mentioned numerical simulations, which consider density‐dependent (convective) multiphase fluid flow, to evaluate impacts of convective fluid flow on the trapping mechanisms and efficiency of injected CO2. The comparison of the results of both numerical simulations shows that convective fluid flow also has significant impacts on hydrogeochemical behavior of injected CO2 and thus its trapping mechanisms and efficiency. Convective fluid flow reduces the free fluid phase of CO2 (i.e., hydrodynamic trapping) and thus enhances the aqueous and solid phases of CO2 (i.e., initially solubility trapping and then mineral trapping).
- 12 June 2012
- Published by American Geophysical Union (AGU) in Journal of Geophysical Research
- Vol. 117 (B6)
Hydrogeochemical numerical simulation of impacts of mineralogical compositions and convective fluid flow on trapping mechanisms and efficiency of carbon dioxide injected into deep saline sandstone aquifers
A series of numerical simulations, which consider density‐dependent (convective) groundwater and carbon dioxide (CO2) flow, is performed using a multiphase hydrogeochemical reactive transport numerical model to evaluate impacts of mineralogical compositions on the trapping mechanisms and efficiency of CO2 injected into a deep saline sandstone aquifer (reservoir rock). The results of the numerical simulations show that the mineralogical compositions of the sandstone aquifer have significant impacts on hydrogeochemical behavior of injected CO2 and thus its trapping mechanisms and efficiency. Injected CO2 is accumulated as a free fluid phase beneath the caprock (i.e., hydrodynamic trapping), then dissolved as aqueous phases such as bicarbonate and carbonate anions into groundwater (i.e., solubility trapping), and finally precipitated as carbonate minerals (i.e., mineral trapping). Mineral trapping of injected CO2 takes places as precipitation of a primary carbonate mineral such as calcite and secondary carbonate minerals such as dawsonite, siderite, ankerite, and magnesite. The patterns of hydrogeochemical reactions depend significantly on the initial presence and absence of chlorite in the sandstone aquifer. For mineral trapping of injected CO2, ankerite is the most dominant mineral when chlorite is initially present, whereas dawsonite is the most dominant mineral when chlorite is initially absent in the sandstone aquifer. Mg2+ and Fe2+, which are essential chemical components of such secondary carbonate minerals (i.e., siderite, ankerite, and magnesite) for mineral trapping of injected CO2, are mainly supplied by dissolution of chlorite. As a result, the precipitation amounts of the secondary carbonate minerals and thus the efficiency of mineral trapping of injected CO2 increase significantly as the volume fraction of chlorite increases in the sandstone aquifer. A series of additional numerical simulations, which consider density‐independent (non‐convective) multiphase fluid flow, is also performed using the same numerical model, and then its results are compared with those of the above‐mentioned numerical simulations, which consider density‐dependent (convective) multiphase fluid flow, to evaluate impacts of convective fluid flow on the trapping mechanisms and efficiency of injected CO2. The comparison of the results of both numerical simulations shows that convective fluid flow also has significant impacts on hydrogeochemical behavior of injected CO2 and thus its trapping mechanisms and efficiency. Convective fluid flow reduces the free fluid phase of CO2 (i.e., hydrodynamic trapping) and thus enhances the aqueous and solid phases of CO2 (i.e., initially solubility trapping and then mineral trapping).
- 1 January 2012
- Published by American Society of Civil Engineers (ASCE) in Journal of Hydrologic Engineering
- Vol. 17 (1) , 10-22
Three-Dimensional Numerical Simulation of Saltwater Extraction Schemes to Mitigate Seawater Intrusion due to Groundwater Pumping in a Coastal Aquifer System
A series of three-dimensional numerical simulations using a multidimensional hydrodynamic dispersion numerical model was performed to analyze various saltwater extraction schemes for mitigating seawater intrusion attributed to groundwater pumping in a coastal aquifer system. A steady-state numerical simulation was performed first to obtain initial (i.e., pregroundwater pumping) steady-state conditions before groundwater pumping, and then a transient-state numerical simulation was performed to obtain intermediate (i.e., postgroundwater pumping) steady-state conditions during groundwater pumping. In the subsequent series of transient-state numerical simulations as scenario and sensitivity analyses, four different saltwater extraction factors such as the amount of saltwater extraction, the number of extraction wells, the horizontal location of extraction wells, and the vertical interval of saltwater extraction were considered to determine an optimal saltwater extraction scheme for the coastal aquifer system ...
- 1 January 2012
- Published by American Society of Civil Engineers (ASCE) in Journal of Hydrologic Engineering
- Vol. 17 (1) , 10-22
Three-Dimensional Numerical Simulation of Saltwater Extraction Schemes to Mitigate Seawater Intrusion due to Groundwater Pumping in a Coastal Aquifer System
A series of three-dimensional numerical simulations using a multidimensional hydrodynamic dispersion numerical model was performed to analyze various saltwater extraction schemes for mitigating seawater intrusion attributed to groundwater pumping in a coastal aquifer system. A steady-state numerical simulation was performed first to obtain initial (i.e., pregroundwater pumping) steady-state conditions before groundwater pumping, and then a transient-state numerical simulation was performed to obtain intermediate (i.e., postgroundwater pumping) steady-state conditions during groundwater pumping. In the subsequent series of transient-state numerical simulations as scenario and sensitivity analyses, four different saltwater extraction factors such as the amount of saltwater extraction, the number of extraction wells, the horizontal location of extraction wells, and the vertical interval of saltwater extraction were considered to determine an optimal saltwater extraction scheme for the coastal aquifer system ...
- 1 December 2007
- Published by Springer Nature in Geosciences Journal
- Vol. 11 (4) , 387-396
Hydraulic conductivity and mechanical stiffness tensors for variably saturated true anisotropic intact rock matrices, joints, joint sets, and jointed rock masses
- 1 December 2007
- Published by Springer Nature in Geosciences Journal
- Vol. 11 (4) , 387-396
Hydraulic conductivity and mechanical stiffness tensors for variably saturated true anisotropic intact rock matrices, joints, joint sets, and jointed rock masses
- 1 June 2006
- Published by Springer Nature in Geosciences Journal
- Vol. 10 (2) , 123-129
Constitutive equations for saturated hydraulic properties of deforming porous geologic media with compressible solid constituents
- 1 June 2006
- Published by Springer Nature in Geosciences Journal
- Vol. 10 (2) , 123-129
Constitutive equations for saturated hydraulic properties of deforming porous geologic media with compressible solid constituents
- 1 November 2005
- Published by Springer Nature in Mathematical Geology
- Vol. 37 (8) , 929-941
Vectorial Formulation of Direction Cosines for Anisotropic Geologic Structures from Their Geologic Angle Measurements
- 1 November 2005
- Published by Springer Nature in Mathematical Geology
- Vol. 37 (8) , 929-941
Vectorial Formulation of Direction Cosines for Anisotropic Geologic Structures from Their Geologic Angle Measurements
- 11 January 2005
- Published by American Geophysical Union (AGU) in Water Resources Research
- Vol. 41 (1)
Three‐dimensional numerical simulation of fully coupled groundwater flow and land deformation in unsaturated true anisotropic aquifers due to groundwater pumping
A hydrogeomechanical numerical model is presented to evaluate three‐dimensional groundwater flow and land deformation in unsaturated true anisotropic aquifers due to groundwater pumping. This multidimensional numerical model is developed on the basis of the fully coupled poroelastic governing equations for saturated‐unsaturated groundwater flow in deforming true anisotropic geologic media and the Galerkin finite element method. A series of true anisotropic aquifers, which comprise variously tilting layers, respectively, and a corresponding isotropic aquifer, which is composed of a geometrically averaged equivalent isotropic material, are simulated for the purpose of comparison. The numerical simulation results show that true anisotropy has significant effects on the spatial distributions and temporal changes of hydraulic head and displacement vector. Such effects of true anisotropy are caused by the uneven partitioning of the hydraulic pumping stress between the vertical and horizontal directions in both groundwater flow and solid skeleton deformation fields. This directionally uneven partitioning of the hydraulic pumping stress results from both the differences in hydraulic and mechanical properties among the principal axes and the discordance between the global coordinate axes and the principal axes.
- 11 January 2005
- Published by American Geophysical Union (AGU) in Water Resources Research
- Vol. 41 (1)
Three‐dimensional numerical simulation of fully coupled groundwater flow and land deformation in unsaturated true anisotropic aquifers due to groundwater pumping
A hydrogeomechanical numerical model is presented to evaluate three‐dimensional groundwater flow and land deformation in unsaturated true anisotropic aquifers due to groundwater pumping. This multidimensional numerical model is developed on the basis of the fully coupled poroelastic governing equations for saturated‐unsaturated groundwater flow in deforming true anisotropic geologic media and the Galerkin finite element method. A series of true anisotropic aquifers, which comprise variously tilting layers, respectively, and a corresponding isotropic aquifer, which is composed of a geometrically averaged equivalent isotropic material, are simulated for the purpose of comparison. The numerical simulation results show that true anisotropy has significant effects on the spatial distributions and temporal changes of hydraulic head and displacement vector. Such effects of true anisotropy are caused by the uneven partitioning of the hydraulic pumping stress between the vertical and horizontal directions in both groundwater flow and solid skeleton deformation fields. This directionally uneven partitioning of the hydraulic pumping stress results from both the differences in hydraulic and mechanical properties among the principal axes and the discordance between the global coordinate axes and the principal axes.
- 1 September 2004
- Published by Springer Nature in Geosciences Journal
- Vol. 8 (3) , 291-300
Fully coupled poroelastic governing equations for groundwater flow and solid skeleton deformation in variably saturated true anisotropic porous geologic media
- 1 September 2004
- Published by Springer Nature in Geosciences Journal
- Vol. 8 (3) , 291-300
Fully coupled poroelastic governing equations for groundwater flow and solid skeleton deformation in variably saturated true anisotropic porous geologic media