Kerry Bardot
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Kerry Bardot has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- James L. McCallum
School of Earth Sciences University of Western Australia Perth Australia
2 shared publications - Adam J. Siade
School of Earth Sciences University of Western Australia Perth Australia
1 shared publication Adam Siade
1 shared publication- Alden M. Provost
U.S. Geological Survey Integrated Modeling and Prediction Division Reston Virginia
1 shared publication - Christian D. Langevin
S.S. Papadopulos & Assoc., Inc., 12 Dove Lane, Saint Paul, MN, USA
1 shared publication Clive Hampton
1 shared publication
Latest Publications
- Open Access
- 6 June 2025
- Published by Elsevier in Environmental Modelling & Software
- Vol. 192
A seamless geo-flow modelling workflow to tackle structural uncertainty using LoopStructural and MODFLOW
- 6 June 2025
- Published by Elsevier in Environmental Modelling & Software
- Vol. 192
Open AccessA seamless geo-flow modelling workflow to tackle structural uncertainty using LoopStructural and MODFLOW
- Open Access
- 16 January 2025
- Published by Wiley in Groundwater
- Vol. 63 (3) , 399-408
Accurate Simulation of Flow through Dipping Aquifers with MODFLOW 6 Using Enhanced Cell Connectivity
In simulations of groundwater flow through dipping aquifers, layers of model cells are often “deformed” to follow the top and bottom elevations of the aquifers. When this approach is used in MODFLOW, adjacent cells within the same model layer are vertically offset from one another, and the standard conductance‐based (two‐point) formulation for flow between cells does not rigorously account for these offsets. The XT3D multi‐point flow formulation in MODFLOW 6 is designed to account for geometric irregularities in the grid, including vertical offsets, and to provide accurate results for both isotropic and anisotropic groundwater flow. A recent study evaluated the performance of the standard formulation and XT3D using a simple, synthetic benchmark model of a steeply dipping aquifer. Although XT3D generally improved the accuracy of flow simulations relative to the standard formulation as expected, neither formulation produced accurate flows in cases that involved large vertical offsets. In this paper, we explain that the inability of XT3D to produce accurate flows in the steeply dipping aquifer benchmark was not due to an inherent limitation of the flow formulation, but rather to the limited cell connectivity inherent in the most commonly used discretization packages in MODFLOW 6. Furthermore, we demonstrate that XT3D is able to produce the expected accuracy when adequate cell connectivity is introduced using MODFLOW's unstructured grid type and the aquifer is discretized vertically using at least two model layers.
- 16 January 2025
- Published by Wiley in Groundwater
- Vol. 63 (3) , 399-408
Open AccessAccurate Simulation of Flow through Dipping Aquifers with MODFLOW 6 Using Enhanced Cell Connectivity
In simulations of groundwater flow through dipping aquifers, layers of model cells are often “deformed” to follow the top and bottom elevations of the aquifers. When this approach is used in MODFLOW, adjacent cells within the same model layer are vertically offset from one another, and the standard conductance‐based (two‐point) formulation for flow between cells does not rigorously account for these offsets. The XT3D multi‐point flow formulation in MODFLOW 6 is designed to account for geometric irregularities in the grid, including vertical offsets, and to provide accurate results for both isotropic and anisotropic groundwater flow. A recent study evaluated the performance of the standard formulation and XT3D using a simple, synthetic benchmark model of a steeply dipping aquifer. Although XT3D generally improved the accuracy of flow simulations relative to the standard formulation as expected, neither formulation produced accurate flows in cases that involved large vertical offsets. In this paper, we explain that the inability of XT3D to produce accurate flows in the steeply dipping aquifer benchmark was not due to an inherent limitation of the flow formulation, but rather to the limited cell connectivity inherent in the most commonly used discretization packages in MODFLOW 6. Furthermore, we demonstrate that XT3D is able to produce the expected accuracy when adequate cell connectivity is introduced using MODFLOW's unstructured grid type and the aquifer is discretized vertically using at least two model layers.
- Open Access
- 20 June 2024
- Published by Wiley in Groundwater
- Vol. 63 (1) , 41-51
Structural Uncertainty Due to Fault Timing: A Multimodel Case Study from the Perth Basin
Faults can fundamentally change a groundwater flow regime and represent a major source of uncertainty in groundwater studies. Much research has been devoted to uncertainty around their location and their barrier‐conduit behavior. However, fault timing is one aspect of fault uncertainty that appears to be somewhat overlooked. Many faulted models feature consistent layer offsets, thereby presuming that block faulting has occurred recently and almost instantaneously. Additionally, barrier and/or conduit behavior is often shown to extend vertically through all layers when a fault may in fact terminate well below‐ground surface. In this study, we create three plausible geological interpretations for a transect in the Perth Basin. Adjacent boreholes show stratigraphic offsets and thickening which indicate faulting; however, fault timing is unknown. Flow modeling demonstrates that the model with the most recent faulting shows profoundly different flow patterns due to aquifer juxtaposition. Additionally, multiple realizations with stochastically generated parameter sets for layer, fault core, and fault damage zone conductivity show that fault timing influences flow more than layer or fault zone conductivity. Finally, fault conduit behavior that penetrates aquitards has significant implications for transport, while fault barrier behavior has surprisingly little. This research advocates for adequate data collection where faults may cause breaches in aquitards due to layer offsets or conduit behavior in the damage zone. It also promotes the use of multiple geological models to address structural uncertainty, and highlights some of the hurdles in doing so such as computational expense and the availability of seamless geological‐flow modeling workflows.
- 20 June 2024
- Published by Wiley in Groundwater
- Vol. 63 (1) , 41-51
Open AccessStructural Uncertainty Due to Fault Timing: A Multimodel Case Study from the Perth Basin
Faults can fundamentally change a groundwater flow regime and represent a major source of uncertainty in groundwater studies. Much research has been devoted to uncertainty around their location and their barrier‐conduit behavior. However, fault timing is one aspect of fault uncertainty that appears to be somewhat overlooked. Many faulted models feature consistent layer offsets, thereby presuming that block faulting has occurred recently and almost instantaneously. Additionally, barrier and/or conduit behavior is often shown to extend vertically through all layers when a fault may in fact terminate well below‐ground surface. In this study, we create three plausible geological interpretations for a transect in the Perth Basin. Adjacent boreholes show stratigraphic offsets and thickening which indicate faulting; however, fault timing is unknown. Flow modeling demonstrates that the model with the most recent faulting shows profoundly different flow patterns due to aquifer juxtaposition. Additionally, multiple realizations with stochastically generated parameter sets for layer, fault core, and fault damage zone conductivity show that fault timing influences flow more than layer or fault zone conductivity. Finally, fault conduit behavior that penetrates aquitards has significant implications for transport, while fault barrier behavior has surprisingly little. This research advocates for adequate data collection where faults may cause breaches in aquitards due to layer offsets or conduit behavior in the damage zone. It also promotes the use of multiple geological models to address structural uncertainty, and highlights some of the hurdles in doing so such as computational expense and the availability of seamless geological‐flow modeling workflows.