Chee Chin Lim
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Chee Chin Lim has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Adrian Ujin Yap
Division of Dentistry, Ng Teng Fong General Hospital, National University Centre for Oral Health, and Faculty of Dentistry National University Health System Singapore Singapore
1 shared publication - Divya Padmanabhan
School of Mathematics and Computer Science at Indian Institute of Technology, Ponda, Goa 403401, India
1 shared publication - Jaclyn L. Neo
Associate Professor of Law, Director of the Centre for Asian Legal Studies, National University of Singapore , Singapore
1 shared publication - Karthik Natarajan
Singapore University of Technology and Design, Singapore 487372
1 shared publication - Louis L. Chen
Operations Research Department, Naval Postgraduate School, Monterey, California 93943
1 shared publication
Latest Publications
- 1 March 2025
- Published by Institute for Operations Research and the Management Sciences (INFORMS) in Management Science
- Vol. 71 (3) , 2696-2713
Robustness to Dependency in Influence Maximization
- 1 March 2025
- Published by Institute for Operations Research and the Management Sciences (INFORMS) in Management Science
- Vol. 71 (3) , 2696-2713
Robustness to Dependency in Influence Maximization
- 1 January 1999
- Published by Wiley in Journal of Oral Rehabilitation
- Vol. 26 (1) , 48-52
The influence of finishing time on the marginal seal of a resin‐modified glass–ionomer and polyacid‐modified resin composite
The aim of this study was to compare the effect of immediate and delayed finishing on the microleakage of encapsulated resin-modified glass-ionomer, Fuji II LC and a polyacid-modified resin composite, Dyract compomer at both the enamel and dentine margins. Standardized Class V cavities were prepared along the cemento-enamel junction on buccal and palatal surfaces of 24 freshly extracted non-carious premolars. Equal numbers of buccal and palatal cavities in each group were restored with Fuji II LC and Dyract compomer following the manufacturer's instructions. The groups with delayed finishing were restored 1 week earlier, stored in saline at 37 degrees C and finished on the same day as the groups with immediate finishing. The specimens were then thermocycled 500 times and subjected to dye penetration testing. The results showed that both materials leaked more at the dentine than enamel margins for both regimes of finishing methods. There was no statistical difference in the microleakage of Dyract finished immediately or later at enamel and dentine margins and Fuji II LC finished immediately or later in dentine. However, a statistical difference existed between the microleakage in Fuji II LC finished immediately and later in enamel.
- 1 January 1999
- Published by Wiley in Journal of Oral Rehabilitation
- Vol. 26 (1) , 48-52
The influence of finishing time on the marginal seal of a resin‐modified glass–ionomer and polyacid‐modified resin composite
The aim of this study was to compare the effect of immediate and delayed finishing on the microleakage of encapsulated resin-modified glass-ionomer, Fuji II LC and a polyacid-modified resin composite, Dyract compomer at both the enamel and dentine margins. Standardized Class V cavities were prepared along the cemento-enamel junction on buccal and palatal surfaces of 24 freshly extracted non-carious premolars. Equal numbers of buccal and palatal cavities in each group were restored with Fuji II LC and Dyract compomer following the manufacturer's instructions. The groups with delayed finishing were restored 1 week earlier, stored in saline at 37 degrees C and finished on the same day as the groups with immediate finishing. The specimens were then thermocycled 500 times and subjected to dye penetration testing. The results showed that both materials leaked more at the dentine than enamel margins for both regimes of finishing methods. There was no statistical difference in the microleakage of Dyract finished immediately or later at enamel and dentine margins and Fuji II LC finished immediately or later in dentine. However, a statistical difference existed between the microleakage in Fuji II LC finished immediately and later in enamel.