Amer Abdulaziz Aldamady
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Amer Abdulaziz Aldamady has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Ali Aldersoni
Department of Architecture Engineering, College of Engineering, University of Ha’il, Ha’il City 81451, Saudi Arabia
2 shared publications - Ayman Ragab
Department of Architectural Engineering, Faculty of Engineering, Aswan University
2 shared publications - Mohamed Hssan Hassan Abdelhafez
Department of Architectural Engineering, College of Engineering, University of Hail, Hail 81422, Saudi Arabia
2 shared publications - Sultan Alfraidi
Department of Architectural Engineering, College of Engineering, University of Hail, Hail 81422, Saudi Arabia
2 shared publications - Amr Sayed Hassan Abdallah
Department of Architectural Engineering, Imam Mohammad Ibn Saud Islamic University (IMSIU), Riyadh 11432, Saudi Arabia
1 shared publication - Ashraf Abdelkarim
Research Centre, Ministry of Housing, AR-Riyadh, Saudi Arabia
1 shared publication
Latest Publications
- Open Access
Evaluating the Energy and Carbon Performance of Advanced Glazing Systems for Hot–Arid Climates: An Integrated Simulation and LCA Approach
This study integrates dynamic energy simulation with lifecycle assessment (LCA) to evaluate the energy and carbon performance of advanced glazing systems suitable for hot–arid climates. Using Design Builder software coupled with OpenLCA, six glazing configurations were analyzed under identical building and climatic conditions. The configurations included a conventional single 3 mm float glass pane (C0) as the reference case, a single 3 mm polycarbonate sheet (C1) representing common local construction practice, and four advanced multi-layer systems (C2–C5) incorporating air, argon, and nanogel insulation layers. The inclusion of C0 enabled direct comparison between typical glass construction and emerging polycarbonate-based systems, thereby enhancing the contextual relevance of the analysis. Results demonstrated that thermal and optical properties of glazing systems strongly influence both operational and embodied carbon outcomes. Relative to the conventional glass reference (C0), the nanogel–argon composite (C5) achieved a 32.4% reduction in annual cooling energy and a 28.9% decrease in total lifecycle carbon emissions, with a carbon payback period of approximately 1.1 years. The operational phase dominated total emissions (>97%), confirming that improvements in glazing thermal performance yield substantial long-term benefits even when embodied impacts are considered. While argon filling provided marginal benefit over air cavities, the nanogel insulation contributed the largest performance enhancement. However, the relatively low visible light transmittance (VLT = 0.27) of the C5 system suggests a potential daylight–comfort trade-off that warrants further investigation. The study demonstrates the importance of integrating energy simulation with lifecycle assessment to identify glazing systems that balance energy efficiency, embodied carbon, and indoor environmental quality in hot–arid regions.
Open AccessEvaluating the Energy and Carbon Performance of Advanced Glazing Systems for Hot–Arid Climates: An Integrated Simulation and LCA Approach
This study integrates dynamic energy simulation with lifecycle assessment (LCA) to evaluate the energy and carbon performance of advanced glazing systems suitable for hot–arid climates. Using Design Builder software coupled with OpenLCA, six glazing configurations were analyzed under identical building and climatic conditions. The configurations included a conventional single 3 mm float glass pane (C0) as the reference case, a single 3 mm polycarbonate sheet (C1) representing common local construction practice, and four advanced multi-layer systems (C2–C5) incorporating air, argon, and nanogel insulation layers. The inclusion of C0 enabled direct comparison between typical glass construction and emerging polycarbonate-based systems, thereby enhancing the contextual relevance of the analysis. Results demonstrated that thermal and optical properties of glazing systems strongly influence both operational and embodied carbon outcomes. Relative to the conventional glass reference (C0), the nanogel–argon composite (C5) achieved a 32.4% reduction in annual cooling energy and a 28.9% decrease in total lifecycle carbon emissions, with a carbon payback period of approximately 1.1 years. The operational phase dominated total emissions (>97%), confirming that improvements in glazing thermal performance yield substantial long-term benefits even when embodied impacts are considered. While argon filling provided marginal benefit over air cavities, the nanogel insulation contributed the largest performance enhancement. However, the relatively low visible light transmittance (VLT = 0.27) of the C5 system suggests a potential daylight–comfort trade-off that warrants further investigation. The study demonstrates the importance of integrating energy simulation with lifecycle assessment to identify glazing systems that balance energy efficiency, embodied carbon, and indoor environmental quality in hot–arid regions.
- Open Access
Spatial Suitability Index for Sustainable Urban Development in Desert Hinterland Using a Geographical-Information-System-Based Multicriteria Decision-Making Approach
This study uses the Aswan Governorate model in southern Upper Egypt to determine the spatial suitability of sustainable urban development in the Egyptian deserts, ensure resource sustainability, and contribute to environmentally sustainable urban and economic growth in line with Egypt’s Vision 2030. To achieve these goals, a GIS-based multicriteria decision-making (GIS-MCDM) approach was used, through an innovative approach for integrating three main indicators: the risk index, environmental sensitivity, and economic resources. These indicators were divided into twenty-four criteria, and their weight was determined according to preference through the analytic hierarchy process (AHP). This study serves developmental, national, and expected regional and local development efforts for developing desert regions in the Aswan Governorate, which exceed 80% of the governorate’s area and represent the future of sustainable urban development. This study found three spatial suitability categories, with the largest between 50 and 70% suitability. The first category, with suitability greater than 70%, covers 27.2% of the Aswan Governorate in the north, on both sides of the Nile. Areas with medium spatial suitability, ranging from 50% to 70%, constitute the second category, accounting for 40.3% of the Aswan Governorate, with a concentration in the central regions. The third category includes areas with low spatial suitability, at less than 50%, which make up 32.5% of the governorate.
Open AccessSpatial Suitability Index for Sustainable Urban Development in Desert Hinterland Using a Geographical-Information-System-Based Multicriteria Decision-Making Approach
This study uses the Aswan Governorate model in southern Upper Egypt to determine the spatial suitability of sustainable urban development in the Egyptian deserts, ensure resource sustainability, and contribute to environmentally sustainable urban and economic growth in line with Egypt’s Vision 2030. To achieve these goals, a GIS-based multicriteria decision-making (GIS-MCDM) approach was used, through an innovative approach for integrating three main indicators: the risk index, environmental sensitivity, and economic resources. These indicators were divided into twenty-four criteria, and their weight was determined according to preference through the analytic hierarchy process (AHP). This study serves developmental, national, and expected regional and local development efforts for developing desert regions in the Aswan Governorate, which exceed 80% of the governorate’s area and represent the future of sustainable urban development. This study found three spatial suitability categories, with the largest between 50 and 70% suitability. The first category, with suitability greater than 70%, covers 27.2% of the Aswan Governorate in the north, on both sides of the Nile. Areas with medium spatial suitability, ranging from 50% to 70%, constitute the second category, accounting for 40.3% of the Aswan Governorate, with a concentration in the central regions. The third category includes areas with low spatial suitability, at less than 50%, which make up 32.5% of the governorate.