DMDavid Moulton

David Moulton

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


David Moulton has a total of 456 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    System identification simulations using the advanced fluid neutral model and wide grid formalism in SOLPS-ITER

    by S.P. Kobussen, S. van Den Kerkhof, F. Cursi, W. de Keyser, G.L. Derks, B. Kool, D. Moulton, K. Verhaegh, M. van Berkel, S. Wiesen

    This work presents a first step towards using the SOLPS-ITER code package (Wiesen 2015 J. Nucl. Mater. 463 480–4) for synthetic system identification (SysID) using multisine perturbations. Numerical modelling is used to replicate SysID experiments performed to establish exhaust control done on MAST-U (Kool 2025 Nat. Energy 10 1116–31), (Van Berkel 2025 DPP 2025 (APS)). These experiments involve perturbing the gas injection rate and observing the Scrape-Off-Layer (SOL) response in the frequency domain. The model used is the Advanced Fluid Neutral (AFN) model of SOLPS-ITER (Horsten 2022 Nucl. Mater. Energy 33 101247), implemented in the Wide Grids version of the code (Dekeyser 2021 Nucl. Mater. Energy 27 100999). The grid was generated with the Grid Optimization and Adaptation Toolbox (Van den kerkhof 2024 Contrib. Plasma Phys. 64 e202300134) and extends to the vessel wall, to enable calculating fluid neutral parameters across the entire domain. New boundary condition types were implemented in the code to allow for multisine gas injection perturbations, as well as reservoir models for remote vessel regions without plasma. In steady state, it is possible to simulate plasmas ranging from attached to deeply detached using different gas injection rates. This allows for comparison between simulation and experimental results at similar levels of detachment. Comparison between simulation and experimental data in the frequency domain shows that the AFN SOLPS-ITER simulations predict faster response times to divertor fuelling perturbations than the experiments, likely in part due to the fluid approximation used for the neutrals. When including the reservoir models for remote vessel regions the phase shifts increase, but are still too low compared to experiments.

  • Open Access

    The role of momentum transfer in the detachment front response to power transients for reactor scale tokamaks

    by Matthew Khan, Mike Kryjak, István Cziegler, Benjamin Dudson, Stuart Henderson, David Moulton, Ryoko Osawa, Christopher P. Ridgers

    We have investigated the response of detached plasmas to multi-ms timescale power transients using 1D simulations of the scrape-off layer on a scale and parameter range relevant for reactor-scale tokamaks, such as the Spherical Tokamak for Energy Production (STEP). Simulations were performed using the fluid code Hermes-3, employing the solver CVODE for robust time integration. Including or disregarding the momentum received by the neutral gas via charge exchange reactions in simulations is found to dramatically affect the detachment front’s response. In the analysis, motion of the ionisation front of a detached plasma is determined by two distinct mechanisms; a fast initial pressure-dominated response as the neutral cloud is rapidly compressed, and a slow burn-through dominated one as the cloud is ionised. The former is only observed if the momentum transfer to neutrals is kept. With transfer of momentum to the neutrals disabled, the plasma only interacts with the neutrals through ionisation and recombination. Thus, the front speed during the transient is determined by the rate of burn-through of the neutrals only. Simulations are compared to a recent semi-empirical reattachment model (Henderson et al 2024 Nucl. Fusion 64 066006), where the best qualitative agreement is seen for cases without neutral momentum and for power rises of ∼ 2 × their baseline power. The difference in these agreements are encompassed by the range of potential fits provided by model parameter choice.

  • Open Access

    Overview of the MAST Upgrade physics programme: testing novel concepts at low aspect ratio to inform future devices

    by J.R. Harrison, A. Aboutaleb, M. Aljunid, S.Y. Allan, R. Allan, A. Alli, H. Anand, Y. Andrew, L.C. Appel, A. Ash, et al.

    The research programme performed on the Mega Amp Spherical Tokamak (MAST) Upgrade experiment has made significant advances in developing the physics understanding of low aspect ratio tokamaks in support of the operation of ITER and design of fusion powerplants. High performance plasma scenarios have been developed to facilitate a broad programme of experiments, in which confinement is constrained by the presence of m / n = 2/1 modes that cause substantial losses of fast ions. The onset of these modes coincides with the q = 2 surface residing in a local minimum in the toroidal current density profile. The maximum electron temperature at the pedestal top, T e,ped is limited with gas fuelling to ∼350 eV to maintain regular ELMs; higher T e,ped results in a transition to a non-stationary ELM-free regime. The operational space of spherical tokamaks has been expanded into small and ELM-free regimes. Strong shaping of the last closed flux surface can induce a transition from large to small ELMs, and ELM suppression with resonant magnetic perturbations has been observed for the first time in a low aspect ratio tokamak. Negative triangularity shaping has induced a transition from ELMy H-mode to a high-performance L-mode regime for the first time in a low aspect ratio tokamak. In studies of fast ion confinement, losses of fast particles due to Global Alfvén Eigenmodes have been identified. Interactions between fast ions generated by off-axis neutral beam injection and thermal neutrals can result in significant losses of fast ions. Experiments with on- and off-axis neutral beam injection exhibit a flux pumping mechanism, where the central safety factor is held to ∼1 in the absence of sawteeth. In studies of pedestal physics, it has been found that elevated main chamber neutral pressures result in an increase in the electron density and reduction in the temperature at the pedestal top. Advances in understanding plasma exhaust include the integration of a high-performance plasma core with detached outer divertors in the X -point target configuration. A newly commissioned lower divertor cryopump reduces the lower divertor neutral pressure by up to 50%, with minimal effect on the main chamber or upper divertor. New measurements and SOLPS-ITER simulations emphasise the importance of plasma–neutral interactions on divertor detachment in the conditions accessible in experiments. Real-time control of the ionisation front location in both divertor chambers independently has been demonstrated in double null experiments, enabled by the tightly baffled divertor chambers.


  • Open Access

    2D electron density profile evolution during detachment in Super-X divertor L-mode discharges on MAST-U

    by N. Lonigro, R.S. Doyle, K. Verhaegh, B. Lipschultz, D. Moulton, P. Ryan, J.S. Allcock, C. Bowman, D. Brida, J. Harrison, et al.

    The improved performance of the long-legged alternative divertor configurations on MAST-U, combining strong baffling and total flux expansion, results in stronger power and momentum losses. These lead to lower electron temperatures and peak particle fluxes at the target compared to conventional divertor configurations. The evolution of the divertor electron density profile in the detached region, measured via coherence imaging spectroscopy, is characterized by a density peak building up near the target, downstream of the detachment front, with increasing upstream density. The peak then moves upstream from the target as the target temperature decreases ( T e < 0.3 eV). This behaviour is in agreement with simplified modelling based on the competition of different ion recombination processes and neutral drag acting on the plasma flow. Comparisons against SOLPS-ITER simulations generally show good agreement in the magnitude of the electron density profiles, both along and across the separatrix, but with some discrepancies in the shape of the profiles in the private flux region and near the target.


  • Open Access

    A novel understanding of the role of plasma-molecular kinetics on divertor power exhaust

    by N. Osborne, K. Verhaegh, D. Moulton, S. Mijin, H. Reimerdes, P. Ryan, N. Lonigro, R. Osawa, K. Murray, S. Kobussen, et al.

    During detachment, a buffer of neutral atoms and molecules builds up between the target and the ionising plasma. Collisions between the plasma and the molecules play an important role in the detachment process. Studies of plasma-molecular kinetics indicate that the gas temperature increases during deepening detachment for a wide range of conditions on the MAST-U and TCV tokamaks. This is related to an increased D 2 lifetime during detachment, leading to more plasma-molecule collisions that raise the molecular temperature. Such collisions subsequently result in power and momentum losses from the divertor plasma during detachment. Using a simplified inference, these losses are estimated using the rotational temperature, neutral pressure and ionisation front position. Significant power losses (about 10% of P SOL ) and dominant momentum losses (majority of the upstream pressure) from plasma-molecule collisions are inferred experimentally in long-legged, strongly baffled, detached divertors (MAST-U Super-X divertor). These findings are consistent with SOLPS-ITER simulations (about 15% of P SOL , and 65% of upstream pressure). Simulations also suggest that 40%–50% of the power crossing the ionisation front is lost downstream. The vibrational distribution obtained is compared with a collisional-radiative model setup using the same rate data as SOLPS-ITER, indicating some qualitative agreements and disagreements, potentially highlighting model gaps with regard to the default rates used. These interpretations highlight the importance of plasma-molecular collisions, leading to power and momentum losses during detachment.


  • Open Access

    On the role of atomic momentum and molecules in self-consistent 1D scrape-off layer simulation of MAST-U, using DIV1D

    by S.P. Kobussen, G.L. Derks, E. Westerhof, D. Moulton, S. Wiesen, K. Verhaegh

    In this paper, the 1D physics-based dynamic scrape-off-layer (SOL) model DIV1D is extended to include molecular interactions and the effects of finite atomic flow velocity parallel to the magnetic field lines. The addition of molecular interactions, atomic flow, and geometric settings in DIV1D leads to qualitative agreement with stationary 1D profiles obtained by mapping 2D SOLPS-ITER simulations for the parallel heat flux, electron temperature, electron density, plasma flow velocity, atomic density, atomic flow velocity and molecular density. Steady-state simulations of DIV1D show higher levels of particle, momentum and heat losses through collisional-radiative interactions between ions and molecules, compared to ions and atoms, in the divertor. Density ramp simulations show that DIV1D is now capable of dynamically transitioning between different SOLPS-ITER equilibria for MAST-U, capturing behaviour throughout the target particle flux rollover into deeply detached regimes.


  • Open Access

    Power balance and divertor asymmetries in the Super-X divertors of MAST-U using SOLPS-ITER*

    by I. Paradela Pérez, B. Lomanowski, J.D. Lore, J. Lovell, D. Moulton, Mast Upgrade Team

    Spherical tokamaks (STs) present unique challenges and opportunities in the area of particle and power exhaust, intensified due to their more compact sizes. Substantial efforts are underway in STs to determine the limits in dissipative operational regimes and advanced divertor solutions, including at MAST-U which provides access to the Super-X divertor configuration. Power balance, and upper/lower divertor asymmetries have been studied using SOLPS-ITER simulations of the MAST-U Super-X divertor. A set of simulations with experimentally inferred transport coefficients with E × B and diamagnetic drifts activated, consisting of density and power scans, and high field side vs low field side gas puff locations, have been used for code experimentation to uncover trends beyond the current experimental parameter space. The upper biased asymmetry (U:L > 1 ) of the ratio of the peaks of the plasma energy flux densities at the outer targets increases with heating power and decreases with gas puff strength, going from symmetric to up to a factor of 15. The upper target electron temperature has been found to be a good ordering quantity for the magnitude of this asymmetry for all heating powers, gas puff strength, and gas puff locations. The lower divertor biased asymmetry (U:L < 1 ) of the radiation patterns processed through SOLPS-based bolometry synthetic diagnostics is in qualitative agreement with resistive bolometry experimental results, and it is in quantitative agreement with the trend of the total volume radiation within the divertors of SOLPS. However, radiation measurements alone are not sufficient to infer the magnitude of the asymmetry of the peaks of the power loads at the targets.


  • Open Access

    Impact of Yacora evaluated molecular effective rate coefficients on detached SOLPS-ITER simulations

    by J. Bryant, K. McKay, J.R. Harrison, D. Moulton, K. Verhaegh, C. Cowley, R.C. Bergmayr, U. Fantz, D. Wünderlich

    Presently, SOLPS-ITER does not replicate the levels of plasma-molecular interactions seen during deep detachment on the Super-X divertors of MAST-Upgrade and TCV. At low temperatures ( T e < 1 eV ) relevant to deep detachment, the AMJUEL reaction database contains discrepancies for detachment relevant molecular processes. In order to correct this the vibrationally resolved ground state Yacora model for H 2 (Yacora H 2 ( X 1 , v ) ) has been used to calculate the vibrational distribution and thus from the cross-sections of the Yacora H 2 ( X 1 , v ) model effective rate coefficients for these molecular processes. Reduced and extended implementations of Yacora H 2 ( X 1 , v ) were constructed to form EIRENE-style databases for use in SOLPS-ITER. The reduced implementation utilises the same processes as EIRENE, but with updated cross-sectional data, whilst the extended implementation adds additional processes. The improved cross-sectional data lowers the threshold for molecular charge exchange (MCX) compared to AMJUEL, whilst the inclusion of the additional processes boosts the vibrational excitation in the molecular ground state providing the additional excitation energy required for MCX to be significant at low temperatures ( T e < 5 eV ). When applied to a SOLPS-ITER isolated divertor leg setup, both implementations produce greater levels of MCX that result in elevated molecular ion densities ( D 2 + ) than the default rate setup. The higher levels of D 2 + contribute to detachment via increased levels of Molecular Activated Recombination and Molecular Activated Dissociation. These plasma-molecular interactions elevate the neutral population. During detachment this has a strong impact on power and momentum losses, as well as elevated levels of Balmer α line emission and an earlier onset of the ion target flux rollover. These effects are strongest when the extended database is used.


  • Open Access

    Overview of physics results from MAST upgrade towards core-pedestal-exhaust integration

    by J.R. Harrison, A. Aboutaleb, S. Ahmed, M. Aljunid, S.Y. Allan, H. Anand, Y. Andrew, L.C. Appel, A. Ash, J. Ashton, et al.

    Recent results from MAST Upgrade are presented, emphasising understanding the capabilities of this new device and deepening understanding of key physics issues for the operation of ITER and the design of future fusion power plants. The impact of MHD instabilities on fast ion confinement have been studied, including the first observation of fast ion losses correlated with Compressional and Global Alfvén Eigenmodes. High-performance plasma scenarios have been developed by tailoring the early plasma current ramp phase to avoid internal reconnection events, resulting in a more monotonic q profile with low central shear. The impact of m/n = 3/2, 2/1 and 1/1 modes on thermal plasma confinement and rotation profiles has been quantified, and scenarios optimised to avoid them have transiently reached values of normalised beta approaching 4.2. In pedestal and ELM physics, a maximum pedestal top temperature of ∼350 eV has been achieved, exceeding the value achieved on MAST at similar heating power. Mitigation of type-I ELMs with n = 1 RMPs has been observed. Studies of plasma exhaust have concentrated on comparing conventional and Super-X divertor configurations, while X-point target, X-divertor and snowflake configurations have been developed and studied in parallel. In L-mode discharges, the separatrix density required to detach the outer divertors is approximately a factor 2 lower in the Super-X than the conventional configuration, in agreement with simulations. Detailed analysis of spectroscopy data from studies of the Super-X configuration reveal the importance of including plasma-molecule interactions and D2 Fulcher band emission to properly quantify the rates of ionisation, plasma-molecule interactions and volumetric recombination processes governing divertor detachment. In H-mode with conventional and Super-X configurations, the outer divertors are attached in the former and detached in the latter with no impact on core or pedestal confinement.


  • Open Access

    Investigations of atomic and molecular processes of NBI-heated discharges in the MAST Upgrade Super-X divertor with implications for reactors

    by Kevin Verhaegh, James Harrison, Bruce Lipschultz, Nicola Lonigro, Stijn Kobussen, David Moulton, Nick Osborne, Peter Ryan, Christian Theiler, Tijs Wijkamp, et al.

    This experimental study presents an in-depth investigation of the performance of the MAST-U Super-X divertor during NBI-heated operation (up to 2.5 MW) focussing on volumetric ion sources and sinks as well as power losses during detachment. The particle balance and power loss analysis revealed the crucial role of Molecular Activated Recombination and Dissociation (MAR and MAD) ion sinks in divertor particle and power balance, which remain pronounced in the change from ohmic to higher power (NBI heated) L-mode conditions. The importance of MAR and MAD remains with double the absorbed NBI heating. MAD results in significant power dissipation (up to ∼20%of PSOL), mostly in the cold ( Te<5eV) detached region. Theoretical and experimental evidence is found for the potential contribution of D−to MAR and MAD, which warrants further study. These results suggest that MAR and MAD can be relevant in higher power conditions than the ohmic conditions studied previously. Post-processing reactor-scale simulations suggests that MAR and MAD can play a significant role in divertor physics and synthetic diagnostic signals of reactor-scale devices, which are currently underestimated in exhaust simulations. This raises implications for the accuracy of reactor-scale divertor simulations of particularly tightly baffled (alternative) divertor configurations.