Koji Aoshima
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Koji Aoshima has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
- Martin Servin
Department of Physics, Umeå University, Umeå, Sweden
5 shared publications - Eddie Wadbro
Department of Mathematics and Computer Science, Karlstad University, SE-651 88 Karlstad, Sweden
3 shared publications - Arvid Fälldin
Umeå University SE-90187 Umeå Sweden
1 shared publication - Eddie Wadbro
Umeå University Sweden
1 shared publication
Latest Publications
- Open Access
- 12 July 2025
- Published by MDPI AG in Automation
- Vol. 6 (3) , 31
Optimizing Autonomous Wheel Loader Performance—An End-to-End Approach
Wheel loaders in mines and construction sites repeatedly load soil from a pile to load receivers. Automating this task presents a challenging planning problem since each loading’s performance depends on the pile state, which depends on previous loadings. We investigate an end-to-end optimization approach considering future loading outcomes and transportation costs between the pile and load receivers. To predict the evolution of the pile state and the loading performance, we use world models that leverage deep neural networks trained on numerous simulated loading cycles. A look-ahead tree search optimizes the sequence of loading actions by evaluating the performance of thousands of action candidates, which expand into subsequent action candidates under the predicted pile states recursively. Test results demonstrate that, over a horizon of 15 sequential loadings, the look-ahead tree search is 6% more efficient than a greedy strategy, which always selects the action that maximizes the current single loading performance, and 14% more efficient than using a fixed loading controller optimized for the nominal case.
- 12 July 2025
- Published by MDPI AG in Automation
- Vol. 6 (3) , 31
Open AccessOptimizing Autonomous Wheel Loader Performance—An End-to-End Approach
Wheel loaders in mines and construction sites repeatedly load soil from a pile to load receivers. Automating this task presents a challenging planning problem since each loading’s performance depends on the pile state, which depends on previous loadings. We investigate an end-to-end optimization approach considering future loading outcomes and transportation costs between the pile and load receivers. To predict the evolution of the pile state and the loading performance, we use world models that leverage deep neural networks trained on numerous simulated loading cycles. A look-ahead tree search optimizes the sequence of loading actions by evaluating the performance of thousands of action candidates, which expand into subsequent action candidates under the predicted pile states recursively. Test results demonstrate that, over a horizon of 15 sequential loadings, the look-ahead tree search is 6% more efficient than a greedy strategy, which always selects the action that maximizes the current single loading performance, and 14% more efficient than using a fixed loading controller optimized for the nominal case.
- Open Access
- 19 July 2024
- Published by Springer Nature in Multibody System Dynamics
- Vol. 64 (1) , 121-148
Examining the simulation-to-reality gap of a wheel loader digging in deformable terrain
We investigate how well a physics-based simulator can replicate a real wheel loader performing bucket filling in a pile of soil. The comparison is made using field-test time series of the vehicle motion and actuation forces, loaded mass, and total work. The vehicle was modeled as a rigid multibody system with frictional contacts, driveline, and linear actuators. For the soil, we tested discrete-element models of different resolutions, with and without multiscale acceleration. The spatiotemporal resolution ranged between 50–400 mm and 2–500 ms, and the computational speed was between 1/10,000 to 5 times faster than real time. The simulation-to-reality gap was found to be around 10% and exhibited a weak dependence on the level of fidelity, e.g., compatible with real-time simulation. Furthermore, the sensitivity of an optimized force-feedback controller under transfer between different simulation domains was investigated. The domain bias was observed to cause a performance reduction of 5% despite the domain gap being about 15%.
- 19 July 2024
- Published by Springer Nature in Multibody System Dynamics
- Vol. 64 (1) , 121-148
Open AccessExamining the simulation-to-reality gap of a wheel loader digging in deformable terrain
We investigate how well a physics-based simulator can replicate a real wheel loader performing bucket filling in a pile of soil. The comparison is made using field-test time series of the vehicle motion and actuation forces, loaded mass, and total work. The vehicle was modeled as a rigid multibody system with frictional contacts, driveline, and linear actuators. For the soil, we tested discrete-element models of different resolutions, with and without multiscale acceleration. The spatiotemporal resolution ranged between 50–400 mm and 2–500 ms, and the computational speed was between 1/10,000 to 5 times faster than real time. The simulation-to-reality gap was found to be around 10% and exhibited a weak dependence on the level of fidelity, e.g., compatible with real-time simulation. Furthermore, the sensitivity of an optimized force-feedback controller under transfer between different simulation domains was investigated. The domain bias was observed to cause a performance reduction of 5% despite the domain gap being about 15%.
- Open Access
- 6 July 2024
- Published by MDPI AG in Automation
- Vol. 5 (3) , 259-281
World Modeling for Autonomous Wheel Loaders
This paper presents a method for learning world models for wheel loaders performing automatic loading actions on a pile of soil. Data-driven models were learned to output the resulting pile state, loaded mass, time, and work for a single loading cycle given inputs that include a heightmap of the initial pile shape and action parameters for an automatic bucket-filling controller. Long-horizon planning of sequential loading in a dynamically changing environment is thus enabled as repeated model inference. The models, consisting of deep neural networks, were trained on data from a 3D multibody dynamics simulation of over 10,000 random loading actions in gravel piles of different shapes. The accuracy and inference time for predicting the loading performance and the resulting pile state were, on average, 95% in 1.2 ms and 97% in 4.5 ms, respectively. Long-horizon predictions were found feasible over 40 sequential loading actions.
- 6 July 2024
- Published by MDPI AG in Automation
- Vol. 5 (3) , 259-281
Open AccessWorld Modeling for Autonomous Wheel Loaders
This paper presents a method for learning world models for wheel loaders performing automatic loading actions on a pile of soil. Data-driven models were learned to output the resulting pile state, loaded mass, time, and work for a single loading cycle given inputs that include a heightmap of the initial pile shape and action parameters for an automatic bucket-filling controller. Long-horizon planning of sequential loading in a dynamically changing environment is thus enabled as repeated model inference. The models, consisting of deep neural networks, were trained on data from a 3D multibody dynamics simulation of over 10,000 random loading actions in gravel piles of different shapes. The accuracy and inference time for predicting the loading performance and the resulting pile state were, on average, 95% in 1.2 ms and 97% in 4.5 ms, respectively. Long-horizon predictions were found feasible over 40 sequential loading actions.
- Open Access
Simulation-Based Optimization of High-Performance Wheel Loading
Having smart and autonomous earthmoving in mind, we explore high-performance wheel loading in a simulated environment. This paper introduces a wheel loader simulator that combines contacting 3D multibody dynamics with a hybrid continuum-particle terrain model, supporting realistic digging forces and soil displacements at real-time performance. A total of 270,000 simulations are run with different loading actions, pile slopes, and soil to analyze how they affect the loading performance. The results suggest that the preferred digging actions should preserve and exploit a steep pile slope. High digging speed favors high productivity, while energy-efficient loading requires a lower dig speed.
Open AccessSimulation-Based Optimization of High-Performance Wheel Loading
Having smart and autonomous earthmoving in mind, we explore high-performance wheel loading in a simulated environment. This paper introduces a wheel loader simulator that combines contacting 3D multibody dynamics with a hybrid continuum-particle terrain model, supporting realistic digging forces and soil displacements at real-time performance. A total of 270,000 simulations are run with different loading actions, pile slopes, and soil to analyze how they affect the loading performance. The results suggest that the preferred digging actions should preserve and exploit a steep pile slope. High digging speed favors high productivity, while energy-efficient loading requires a lower dig speed.