Caitlin E. Evans
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Caitlin E. Evans has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
M. Saensukjaroenphon
7 shared publicationsC. B. Paulk
5 shared publicationsC. R. Stark
4 shared publications- Chad B. Paulk
Kansas State University
4 shared publications - Charles R. Stark
Kansas State University
4 shared publications - Cassandra K. Jones
Kansas State University Kansas State University Kansas State University
3 shared publications
Latest Publications
- Open Access
- 1 January 2022
- Published by Kansas State University in Kansas Agricultural Experiment Station Research Reports
- Vol. 8 (11) , 4
Effect of Feed Form, Corn Particle Size, and Extrusion of Corn on Broiler Performance
The pelleting and extrusion processes use both thermal and mechanical energies to alter the crystalline structure of the starch granule, which makes it more digestible than raw starch. The particle size of the ground corn particle in the diet also affects the rate at which gelatinization occurs in the extrusion process. There is limited research on broiler performance when feeding diets that contain different particle sizes of corn prior to extrusion. The objective of this study was to determine the effect of feed form, corn particle size and the extrusion of corn on growth performance of 21-d-old broiler chicks. To determine the effect of corn type on growth performance, treatments were arranged in a 2 × 3 factorial of corn type (raw corn and extruded corn) and corn particle size (400, 800, and 1200 μm). There was no interaction (P > 0.742) between corn type and corn particle size on d 21 BW, ADFI, or feed conversion ratio (FCR). Broilers fed the raw corn diet had greater (P < 0.001) d 21 BW and ADFI compared to those fed the extruded corn diets. There was no evidence of difference (P > 0.081) in d 21 BW and ADFI in broilers fed the three different corn particle sizes. Broilers fed diets with increasing corn particle size had increased (linear, P = 0.015) FCR. There was an interaction (P < 0.039) between corn type and corn particle size on both the relative gizzard and pancreas weights of broilers. To determine the effects of feed form on growth performance and relative gizzard and pancreas weight, treatments were arranged in a 2 × 2 factorial of feed form (mash and crumble feed) and corn particle size (400 and 800 μm). There was no evidence of interaction (P > 0.180) between feed form and corn particle size on growth performance or relative gizzard and pancreas weight. Broilers fed the crumble extruded corn diet had increased (P = 0.001) d 21 BW and ADFI compared to those fed the mash extruded corn diets. There was no evidence of difference (P > 0.189) in d 21 BW, ADFI, and FCR between broilers fed extruded diets containing 400 μm corn and 800 μm corn regardless of feed form. Broilers fed the mash extruded corn diet had greater (P < 0.001) relative gizzard and pancreas weights as compared to those fed the crumbled extruded corn diets. In addition, broiler
- 1 January 2022
- Published by Kansas State University in Kansas Agricultural Experiment Station Research Reports
- Vol. 8 (11) , 4
Open AccessEffect of Feed Form, Corn Particle Size, and Extrusion of Corn on Broiler Performance
The pelleting and extrusion processes use both thermal and mechanical energies to alter the crystalline structure of the starch granule, which makes it more digestible than raw starch. The particle size of the ground corn particle in the diet also affects the rate at which gelatinization occurs in the extrusion process. There is limited research on broiler performance when feeding diets that contain different particle sizes of corn prior to extrusion. The objective of this study was to determine the effect of feed form, corn particle size and the extrusion of corn on growth performance of 21-d-old broiler chicks. To determine the effect of corn type on growth performance, treatments were arranged in a 2 × 3 factorial of corn type (raw corn and extruded corn) and corn particle size (400, 800, and 1200 μm). There was no interaction (P > 0.742) between corn type and corn particle size on d 21 BW, ADFI, or feed conversion ratio (FCR). Broilers fed the raw corn diet had greater (P < 0.001) d 21 BW and ADFI compared to those fed the extruded corn diets. There was no evidence of difference (P > 0.081) in d 21 BW and ADFI in broilers fed the three different corn particle sizes. Broilers fed diets with increasing corn particle size had increased (linear, P = 0.015) FCR. There was an interaction (P < 0.039) between corn type and corn particle size on both the relative gizzard and pancreas weights of broilers. To determine the effects of feed form on growth performance and relative gizzard and pancreas weight, treatments were arranged in a 2 × 2 factorial of feed form (mash and crumble feed) and corn particle size (400 and 800 μm). There was no evidence of interaction (P > 0.180) between feed form and corn particle size on growth performance or relative gizzard and pancreas weight. Broilers fed the crumble extruded corn diet had increased (P = 0.001) d 21 BW and ADFI compared to those fed the mash extruded corn diets. There was no evidence of difference (P > 0.189) in d 21 BW, ADFI, and FCR between broilers fed extruded diets containing 400 μm corn and 800 μm corn regardless of feed form. Broilers fed the mash extruded corn diet had greater (P < 0.001) relative gizzard and pancreas weights as compared to those fed the crumbled extruded corn diets. In addition, broiler
- Open Access
- 1 January 2020
- Published by Kansas State University in Kansas Agricultural Experiment Station Research Reports
- Vol. 6 (10) , 26
Effect of Pellet Cooling Method, Sample Preparation, Storage Condition, and Storage Time on Phytase Activity of a Swine Diet
Temperature and moisture content have been identified as two factors that influence enzyme inactivation. Phytase may be further degraded in feed samples if there is moisture left in the sample and it is not properly stored prior to analysis. Therefore, the objective of this experiment was to determine the effect of cooling method, sample preparation, storage condition, and storage time on phytase stability. In Exp. 1, treatments were arranged in 2 × 2 factorial with main effects of sample preparation (none or freeze-dried) and storage condition (ambient storage or freezer storage). Diets were mixed 3 separate times to provide 3 replicates per treatment. The result of Exp. 1 demonstrated that there was no interaction between drying process and storage condition for mash samples collected from the mixer. The sample drying process and storage condition did not impact the phytase stability. In Exp. 2, treatments were arranged in a 2 × 3 factorial with main effects of cooling method (counterflow cooler or freezer) and sample preparation (non-dried then freezer storage, freeze-dried then freezer storage, freeze-dried then ambient storage). The diet was steam conditioned for approximately 45 s at 185°F using a 5.1- × 35.8-in single shaft conditioner of a pellet mill (California Pellet Mill model Cl-5, Crawfordsville, IN) at a production rate of 2.2 lb/min by holding the feeder at a constant speed setting. The sample was collected at the end of the conditioner and did not pass the pellet die. The conditioner was run 3 separate times to provide 3 replicates for each treatment. The result of Exp. 2 demonstrated that there was no interaction between the cooling method and sample preparation for phytase stability of conditioned mash samples. The cooling method and sample preparation did not affect the phytase stability. In Exp. 3, treatments were arranged in a 5 × 3 × 2 factorial with main effects of cooling method (none, heat diffusion, experimental fan cooler, experimental counterflow cooler, or freezer), storage condition (ziplock/ ambient, ziplock/frozen, and vacuum/frozen), and storage time (1 or 3 wk.). The diet was steam conditioned for approximately 45 s at 185°F and pelleted using a pellet mill (California Pellet Mill model Cl-5, Crawfordsville, IN) equipped with 0.16- × 0.50-in die. The diet was pelleted at a production rate of 2.2 lb/min by holding the feeder at a constant speed setting. The pellet mill was run 3 separate times to provide 3 replicates for each
- 1 January 2020
- Published by Kansas State University in Kansas Agricultural Experiment Station Research Reports
- Vol. 6 (10) , 26
Open AccessEffect of Pellet Cooling Method, Sample Preparation, Storage Condition, and Storage Time on Phytase Activity of a Swine Diet
Temperature and moisture content have been identified as two factors that influence enzyme inactivation. Phytase may be further degraded in feed samples if there is moisture left in the sample and it is not properly stored prior to analysis. Therefore, the objective of this experiment was to determine the effect of cooling method, sample preparation, storage condition, and storage time on phytase stability. In Exp. 1, treatments were arranged in 2 × 2 factorial with main effects of sample preparation (none or freeze-dried) and storage condition (ambient storage or freezer storage). Diets were mixed 3 separate times to provide 3 replicates per treatment. The result of Exp. 1 demonstrated that there was no interaction between drying process and storage condition for mash samples collected from the mixer. The sample drying process and storage condition did not impact the phytase stability. In Exp. 2, treatments were arranged in a 2 × 3 factorial with main effects of cooling method (counterflow cooler or freezer) and sample preparation (non-dried then freezer storage, freeze-dried then freezer storage, freeze-dried then ambient storage). The diet was steam conditioned for approximately 45 s at 185°F using a 5.1- × 35.8-in single shaft conditioner of a pellet mill (California Pellet Mill model Cl-5, Crawfordsville, IN) at a production rate of 2.2 lb/min by holding the feeder at a constant speed setting. The sample was collected at the end of the conditioner and did not pass the pellet die. The conditioner was run 3 separate times to provide 3 replicates for each treatment. The result of Exp. 2 demonstrated that there was no interaction between the cooling method and sample preparation for phytase stability of conditioned mash samples. The cooling method and sample preparation did not affect the phytase stability. In Exp. 3, treatments were arranged in a 5 × 3 × 2 factorial with main effects of cooling method (none, heat diffusion, experimental fan cooler, experimental counterflow cooler, or freezer), storage condition (ziplock/ ambient, ziplock/frozen, and vacuum/frozen), and storage time (1 or 3 wk.). The diet was steam conditioned for approximately 45 s at 185°F and pelleted using a pellet mill (California Pellet Mill model Cl-5, Crawfordsville, IN) equipped with 0.16- × 0.50-in die. The diet was pelleted at a production rate of 2.2 lb/min by holding the feeder at a constant speed setting. The pellet mill was run 3 separate times to provide 3 replicates for each
- Open Access
- 1 January 2020
- Published by Kansas State University in Kansas Agricultural Experiment Station Research Reports
- Vol. 6 (10) , 30
Effect of Added Water, Holding Time, or Phytase Analysis Method on Phytase Stability and Pellet Quality
The addition of water to the mixer prior to pelleting is sometimes necessary to reach the target moisture content at the end of the conditioning process. However, there are limited data to demonstrate the impact of water addition in the mixer on phytase stability during the pelleting process. In addition, the variation of phytase analysis method may lead to incorrect or biased conclusions for research on industrial phytase stability. Therefore, the objective of this experiment was to determine the effect of water added in the mixer, feed holding time, and phytase analysis method on phytase stability and pellet quality. Treatments were arranged in a 2 × 2 × 2 factorial with main effects of added water (0% or 1%), holding time (0 or 2 h), and phytase analysis method (ELISA or EN ISO), respectively. For the 0% added water treatment, a 210-lb basal feed and 0.03-lb phytase were mixed for 5 min. For the 1% added water treatments, a 208-lb basal feed and 0.03-lb phytase were mixed for 120 s followed by the addition of 2-lb water and then the mixture was mixed for 180 s wet mix time. The water was applied to dry feed in the mixer using a hand-held sprayer (Country Tuff model 26329, Sedalia, MO) with a flat spray tip nozzle (TeeJet model TP11006, Glendale Heights, IL). After the diets were mixed, treatments were immediately pelleted or held in a closed container for 2 h before pelleting. Treatments were steam conditioned at 185°F for approximately 30 s and pelleted using a pellet mill (California Pellet Mill Co. model Cl-5, Crawfordsville, IN). The pellet mill was equipped with a 0.16 × 0.87 in die. Samples were collected during discharge of the mixer, after conditioning and after pelleting. The conditioned mash and pelleted samples were cooled for 10 min using an experimental counterflow cooler. There were 3 replicates per treatment. Data were analyzed using the GLIMMIX procedure of SAS. The results demonstrated that there was no evidence of three-way or two-way interactions among added water, holding time, and analysis method on phytase stability for mash samples, conditioned mash samples, and pellets. The added water and holding time did not impact phytase stability for mash samples, conditioned mash samples, and pellets. The ELISA method had greater (P = 0.004) phytase activity than the EN ISO method for the pellet samples. The phytase activity was similar between the two analytical
- 1 January 2020
- Published by Kansas State University in Kansas Agricultural Experiment Station Research Reports
- Vol. 6 (10) , 30
Open AccessEffect of Added Water, Holding Time, or Phytase Analysis Method on Phytase Stability and Pellet Quality
The addition of water to the mixer prior to pelleting is sometimes necessary to reach the target moisture content at the end of the conditioning process. However, there are limited data to demonstrate the impact of water addition in the mixer on phytase stability during the pelleting process. In addition, the variation of phytase analysis method may lead to incorrect or biased conclusions for research on industrial phytase stability. Therefore, the objective of this experiment was to determine the effect of water added in the mixer, feed holding time, and phytase analysis method on phytase stability and pellet quality. Treatments were arranged in a 2 × 2 × 2 factorial with main effects of added water (0% or 1%), holding time (0 or 2 h), and phytase analysis method (ELISA or EN ISO), respectively. For the 0% added water treatment, a 210-lb basal feed and 0.03-lb phytase were mixed for 5 min. For the 1% added water treatments, a 208-lb basal feed and 0.03-lb phytase were mixed for 120 s followed by the addition of 2-lb water and then the mixture was mixed for 180 s wet mix time. The water was applied to dry feed in the mixer using a hand-held sprayer (Country Tuff model 26329, Sedalia, MO) with a flat spray tip nozzle (TeeJet model TP11006, Glendale Heights, IL). After the diets were mixed, treatments were immediately pelleted or held in a closed container for 2 h before pelleting. Treatments were steam conditioned at 185°F for approximately 30 s and pelleted using a pellet mill (California Pellet Mill Co. model Cl-5, Crawfordsville, IN). The pellet mill was equipped with a 0.16 × 0.87 in die. Samples were collected during discharge of the mixer, after conditioning and after pelleting. The conditioned mash and pelleted samples were cooled for 10 min using an experimental counterflow cooler. There were 3 replicates per treatment. Data were analyzed using the GLIMMIX procedure of SAS. The results demonstrated that there was no evidence of three-way or two-way interactions among added water, holding time, and analysis method on phytase stability for mash samples, conditioned mash samples, and pellets. The added water and holding time did not impact phytase stability for mash samples, conditioned mash samples, and pellets. The ELISA method had greater (P = 0.004) phytase activity than the EN ISO method for the pellet samples. The phytase activity was similar between the two analytical
- Open Access
- 1 January 2020
- Published by Kansas State University in Kansas Agricultural Experiment Station Research Reports
- Vol. 6 (10) , 28
Evaluation of Conditioning Temperature and Die Specifications on Nursery Pig Performance
The objective of this study was to determine the effects on growth performance in nursery pigs that is linked to the conditioning temperature and die specifications used during the feed pelleting process. A total of 315 barrows (DNA; 200 × 400; initial BW 13.2 lb) were used in a 35-d growth trial. Upon arrival, pigs were weighed and assigned to pens in a completely randomized design with 5 pigs per pen, and each pen was randomly assigned to 1 of 7 dietary treatments with 9 replications per treatment. Treatments consisted of a mash control (MC) and 6 pelleted diets manufactured using 2 different pellet dies (length/diameter [L:D]: 6.7 and 2.7) and 3 different conditioning temperatures (low, medium, high). Conditioning temperatures for Phase 1 diets pelleted using the 6.7 L:D die were 80, 100, and 120°F and for the die with a L:D 2.7 were 100, 120, and 140°F for the low, medium, and high, respectively. Phase 2 conditioning temperatures for diets pelleted using the die with a L:D of 6.7 were approximately 120, 140, and 160°F and for the 2.7 L:D die were 140, 160, and 180°F for the low, medium, and high, respectively. Diets were fed in three phases as follows, Phase 1: d 0 to 10, Phase 2: d 10 to 25, and Phase 3: d 25 to 35. During Phase 3 all pigs were fed a common mash diet. Overall from d 0 to 35, similar ADG was observed for pigs fed the MC or pelleted diets with the exception of the diet pelleted at the low conditioning temperature using the 6.7 L:D die, which had decreased (P < 0.05) ADG compared to MC. When pelleting diets using the 2.7 L:D die, there was a tendency for increased (quadratic, P = 0.077) ADG in pigs fed diets conditioned at increasing temperatures, with the medium temperature having the greatest ADG. There was a tendency for increased (P = 0.088) ADG in pigs fed diets pelleted using the 2.7 L:D die compared to the 6.7 L:D die. Pigs fed pelleted diets, with the exception of the medium temperature on the 2.7 L:D die, had decreased (P < 0.05) ADFI compared to the MC. However, diets pelleted using the 6.7 L:D die as well as the diet manufactured at the medium conditioning temperature on the 2.7 L:D die had improved (P < 0.05) F/G compared to the MC diet. Additionally,
- 1 January 2020
- Published by Kansas State University in Kansas Agricultural Experiment Station Research Reports
- Vol. 6 (10) , 28
Open AccessEvaluation of Conditioning Temperature and Die Specifications on Nursery Pig Performance
The objective of this study was to determine the effects on growth performance in nursery pigs that is linked to the conditioning temperature and die specifications used during the feed pelleting process. A total of 315 barrows (DNA; 200 × 400; initial BW 13.2 lb) were used in a 35-d growth trial. Upon arrival, pigs were weighed and assigned to pens in a completely randomized design with 5 pigs per pen, and each pen was randomly assigned to 1 of 7 dietary treatments with 9 replications per treatment. Treatments consisted of a mash control (MC) and 6 pelleted diets manufactured using 2 different pellet dies (length/diameter [L:D]: 6.7 and 2.7) and 3 different conditioning temperatures (low, medium, high). Conditioning temperatures for Phase 1 diets pelleted using the 6.7 L:D die were 80, 100, and 120°F and for the die with a L:D 2.7 were 100, 120, and 140°F for the low, medium, and high, respectively. Phase 2 conditioning temperatures for diets pelleted using the die with a L:D of 6.7 were approximately 120, 140, and 160°F and for the 2.7 L:D die were 140, 160, and 180°F for the low, medium, and high, respectively. Diets were fed in three phases as follows, Phase 1: d 0 to 10, Phase 2: d 10 to 25, and Phase 3: d 25 to 35. During Phase 3 all pigs were fed a common mash diet. Overall from d 0 to 35, similar ADG was observed for pigs fed the MC or pelleted diets with the exception of the diet pelleted at the low conditioning temperature using the 6.7 L:D die, which had decreased (P < 0.05) ADG compared to MC. When pelleting diets using the 2.7 L:D die, there was a tendency for increased (quadratic, P = 0.077) ADG in pigs fed diets conditioned at increasing temperatures, with the medium temperature having the greatest ADG. There was a tendency for increased (P = 0.088) ADG in pigs fed diets pelleted using the 2.7 L:D die compared to the 6.7 L:D die. Pigs fed pelleted diets, with the exception of the medium temperature on the 2.7 L:D die, had decreased (P < 0.05) ADFI compared to the MC. However, diets pelleted using the 6.7 L:D die as well as the diet manufactured at the medium conditioning temperature on the 2.7 L:D die had improved (P < 0.05) F/G compared to the MC diet. Additionally,
- Open Access
- 1 January 2020
- Published by Kansas State University in Kansas Agricultural Experiment Station Research Reports
- Vol. 6 (10) , 25
Impact of Storage Conditions and Premix Type on Fat-Soluble Vitamin Stability
The objective of Exp. 1 was to determine the impact of 0, 30, 60, or 90 d storage time on fat-soluble vitamin stability when vitamin premix (VP) and vitamin trace mineral premix (VTM) are blended with 1% inclusion of medium chain fatty acids (MCFA; 1:1:1 blend of C6:C8:C10) or mineral oil (MO) with different environmental conditions. Treatments were arranged as a 2 × 2 × 2 × 4 factorial, with 2 premix type (VP or VTM), 2 oil type (MO or MCFA), 2 storage conditions [room temperature (RT) or high-heat, high-humidity (HTHH)] and 3 storage times (30, 60, or 90 d). Samples were stored at room temperature in a temperature-controlled laboratory (approximately 72°F) for RT or in an environmentally-controlled chamber set at 104°F and 75% humidity for HTHH. For Exp. 1, there was a premix type × oil type × storage time interaction of vitamin A (P = 0.002). Vitamin A was stable in VP mixed with MCFA and VTM mixed with MO when stored from 0 to 90 d. Increasing the storage time continued to degrade vitamin A in VP mixed with MO and VTM mixed with MCFA. There was a premix type × storage condition interaction (P < 0.01). When premixes were stored under HTHH, the VTM had greater vitamin A stability as compared to VP. However, there was no difference for vitamin A stability between VP and VTM when stored under RT. There was an oil type × storage condition interaction (P < 0.01). The premixes with MO had a higher vitamin A stability compared to the premixes with MCFA when stored at RT. However, there was no difference for vitamin A stability between premix with MO and MCFA when stored at HTHH. There was a storage condition × time interaction (P < 0.01). When premixes were stored at HTHH, the vitamin A stability decreased as storage time increased to d 90. However, there was no difference in vitamin A stability as storage time increased to d 90 when stored at RT. Vitamin D3 stability was increased (P < 0.002) when stored at RT compared to premixes stored at HTHH. There was a decrease in vitamin D3 stability as storage time increased (P = 0.002) from d 30 to 60; however, there was no further decrease from d 60 to 90. There was a storage condition × time interaction (P < 0.001) for vitamin E stability. Vitamin
- 1 January 2020
- Published by Kansas State University in Kansas Agricultural Experiment Station Research Reports
- Vol. 6 (10) , 25
Open AccessImpact of Storage Conditions and Premix Type on Fat-Soluble Vitamin Stability
The objective of Exp. 1 was to determine the impact of 0, 30, 60, or 90 d storage time on fat-soluble vitamin stability when vitamin premix (VP) and vitamin trace mineral premix (VTM) are blended with 1% inclusion of medium chain fatty acids (MCFA; 1:1:1 blend of C6:C8:C10) or mineral oil (MO) with different environmental conditions. Treatments were arranged as a 2 × 2 × 2 × 4 factorial, with 2 premix type (VP or VTM), 2 oil type (MO or MCFA), 2 storage conditions [room temperature (RT) or high-heat, high-humidity (HTHH)] and 3 storage times (30, 60, or 90 d). Samples were stored at room temperature in a temperature-controlled laboratory (approximately 72°F) for RT or in an environmentally-controlled chamber set at 104°F and 75% humidity for HTHH. For Exp. 1, there was a premix type × oil type × storage time interaction of vitamin A (P = 0.002). Vitamin A was stable in VP mixed with MCFA and VTM mixed with MO when stored from 0 to 90 d. Increasing the storage time continued to degrade vitamin A in VP mixed with MO and VTM mixed with MCFA. There was a premix type × storage condition interaction (P < 0.01). When premixes were stored under HTHH, the VTM had greater vitamin A stability as compared to VP. However, there was no difference for vitamin A stability between VP and VTM when stored under RT. There was an oil type × storage condition interaction (P < 0.01). The premixes with MO had a higher vitamin A stability compared to the premixes with MCFA when stored at RT. However, there was no difference for vitamin A stability between premix with MO and MCFA when stored at HTHH. There was a storage condition × time interaction (P < 0.01). When premixes were stored at HTHH, the vitamin A stability decreased as storage time increased to d 90. However, there was no difference in vitamin A stability as storage time increased to d 90 when stored at RT. Vitamin D3 stability was increased (P < 0.002) when stored at RT compared to premixes stored at HTHH. There was a decrease in vitamin D3 stability as storage time increased (P = 0.002) from d 30 to 60; however, there was no further decrease from d 60 to 90. There was a storage condition × time interaction (P < 0.001) for vitamin E stability. Vitamin
- Open Access
- 1 January 2019
- Published by Kansas State University in Kansas Agricultural Experiment Station Research Reports
- Vol. 5 (8) , 38
Effects of Grinding Corn with Different Moisture Concentrations on Subsequent Particle Size and Flowability Characteristics
The objective of this study was to determine the effects of whole corn moisture and hammermill screen size on subsequent ground corn moisture, particle size, and flow- ability. Whole yellow dent #2 corn was used for this experiment. Treatments were arranged as a 2 × 2 factorial design with two moisture concentrations (as-received and high) each ground using 2 hammermill screen sizes (1/8 and 1/4 in). Corn was ground using a laboratory scale 1.5 HP Bliss Hammermill (Model 6K630B) at 3 separate time points to create 3 replications per treatment. Increasing initial whole corn moisture was accomplished by adding 5% water and heating at 55°C for 3 hours in sealed glass jars using a Fisherbrand Isotemp Oven (Model 15-103-051). Ground corn flowability was calculated using angle of repose (AOR), percent compressibility, and critical orifice diameter (COD) measurements to determine the composite flow index (CFI). There was no evidence for a screen size × corn moisture interaction for moisture content, particle size, standard deviation, or flowability metrics. Grinding corn using a 1/8 in screen resulted in decreased (P < 0.041) moisture content compared to corn ground using the 1/4 in screen. There was a decrease in particle size from the 1/4 in screen to the 1/8 in but no evidence of difference was observed for the standard deviation. There was a decrease (P < 0.03) in percent compressibility as screen size increased from 1/8 to 1/4 in. Angle of repose tended to decrease (P < 0 .056) when corn was ground using a 1/4 in screen compared to a 1/8 in screen. For the main effects of moisture content, high moisture corn had increased (P < 0.0001) ground corn moisture content compared to as-received corn. As-received corn resulted in decreased (P < 0.029) particle size and an increased standard deviation compared to the high moisture corn. Increased moisture content of corn increased (P < 0.038) CFI and tended to decrease (P < 0.056) AOR and COD. In conclusion, decreasing hammermill screen size increased moisture loss by 0.55%, corn particle size by 126 μm, and resulted in poorer flowability as measured by percent compressibility and AOR. High moisture corn increased subsequent particle size by 89 μm, therefore improving flowability as measured by CFI.
- 1 January 2019
- Published by Kansas State University in Kansas Agricultural Experiment Station Research Reports
- Vol. 5 (8) , 38
Open AccessEffects of Grinding Corn with Different Moisture Concentrations on Subsequent Particle Size and Flowability Characteristics
The objective of this study was to determine the effects of whole corn moisture and hammermill screen size on subsequent ground corn moisture, particle size, and flow- ability. Whole yellow dent #2 corn was used for this experiment. Treatments were arranged as a 2 × 2 factorial design with two moisture concentrations (as-received and high) each ground using 2 hammermill screen sizes (1/8 and 1/4 in). Corn was ground using a laboratory scale 1.5 HP Bliss Hammermill (Model 6K630B) at 3 separate time points to create 3 replications per treatment. Increasing initial whole corn moisture was accomplished by adding 5% water and heating at 55°C for 3 hours in sealed glass jars using a Fisherbrand Isotemp Oven (Model 15-103-051). Ground corn flowability was calculated using angle of repose (AOR), percent compressibility, and critical orifice diameter (COD) measurements to determine the composite flow index (CFI). There was no evidence for a screen size × corn moisture interaction for moisture content, particle size, standard deviation, or flowability metrics. Grinding corn using a 1/8 in screen resulted in decreased (P < 0.041) moisture content compared to corn ground using the 1/4 in screen. There was a decrease in particle size from the 1/4 in screen to the 1/8 in but no evidence of difference was observed for the standard deviation. There was a decrease (P < 0.03) in percent compressibility as screen size increased from 1/8 to 1/4 in. Angle of repose tended to decrease (P < 0 .056) when corn was ground using a 1/4 in screen compared to a 1/8 in screen. For the main effects of moisture content, high moisture corn had increased (P < 0.0001) ground corn moisture content compared to as-received corn. As-received corn resulted in decreased (P < 0.029) particle size and an increased standard deviation compared to the high moisture corn. Increased moisture content of corn increased (P < 0.038) CFI and tended to decrease (P < 0.056) AOR and COD. In conclusion, decreasing hammermill screen size increased moisture loss by 0.55%, corn particle size by 126 μm, and resulted in poorer flowability as measured by percent compressibility and AOR. High moisture corn increased subsequent particle size by 89 μm, therefore improving flowability as measured by CFI.
- Open Access
- 1 January 2019
- Published by Kansas State University in Kansas Agricultural Experiment Station Research Reports
- Vol. 5 (8) , 30
Effect of Die Retention Time on Pellet Quality and Phytase Stability of a Corn-Soybean Meal Swine Diet
Phytase is a phosphohydrolytic enzyme that releases phosphorus from phytate in animal feed. However, pelleting is a thermal process that can denature phytase. It is hypothesized that there are many factors that can account for phytase denaturing during the pelleting process, such as pellet mill model, die length to diameter ratio (L:D), steam quality, and residence time in conditioner and die. Therefore, the objective of this experiment was to determine the effect of pellet mill model, die thickness, and die retention time on pellet quality and phytase stability. Treatments were arranged as a completely randomized design to determine the effect of die retention time (RT). Diets were pelleted using either a 1012-2 HD California Pellet Mill (CPM) Master Model or a 3016-4 HD CPM Master Model equipped with a 3/16 × 2 in (10.6 L:D), a 3/16 × 1 1/4 in (6.6 L:D) or a 3/16 × 1 3/4 in (9.3 L:D) with 30 sec conditioning retention time at 185°F with designated production rate. These processing conditions were used to create the following RT treatments: 10.6 L:D with 4.3 sec RT, 10.6 L:D with 2.9 sec RT, 9.3 L:D with 1.7 sec RT, 9.3 L:D with 1.1 sec RT, 6.6 L:D with 2.6 sec RT, and 6.6 L:D with 1.6 sec RT. The pellet mills were run 3 separate times to provide 3 replicates for each treatment. There was an overall effect (P < 0.001) of treatment on phytase stability in cooled pellets. When using the 1012 PM, phytase was more stable regardless of die retention time when diets were manufactured using the 6.6 L:D die compared to the 10.6 L:D die (P < 0.05). The hot pellet temperature of 10.6 L:D die was 195–211°F, while 6.6 L:D die was 184–189°F. However, the phytase stability was similar between the feed pelleted with 1012 PM equipped with 6.6 L:D die and the 3016 PM equipped with 9.3 L:D regardless of retention time (P > 0.05). The hot pellet temperature of feed pelleted with the 1012 PM equipped with 6.6 L:D die was 184–189°F, while the feed pelleted with the 3016 die equipped with 9.3 L:D die was 180–183°F. There was also a quadratic decrease in phytase stability as the die L:D increased (P < 0.0001). There- fore, the pellet mill size or die retention time did not affect phytase stability when the hot pellet temperature was less than 189°F. Pellet quality
- 1 January 2019
- Published by Kansas State University in Kansas Agricultural Experiment Station Research Reports
- Vol. 5 (8) , 30
Open AccessEffect of Die Retention Time on Pellet Quality and Phytase Stability of a Corn-Soybean Meal Swine Diet
Phytase is a phosphohydrolytic enzyme that releases phosphorus from phytate in animal feed. However, pelleting is a thermal process that can denature phytase. It is hypothesized that there are many factors that can account for phytase denaturing during the pelleting process, such as pellet mill model, die length to diameter ratio (L:D), steam quality, and residence time in conditioner and die. Therefore, the objective of this experiment was to determine the effect of pellet mill model, die thickness, and die retention time on pellet quality and phytase stability. Treatments were arranged as a completely randomized design to determine the effect of die retention time (RT). Diets were pelleted using either a 1012-2 HD California Pellet Mill (CPM) Master Model or a 3016-4 HD CPM Master Model equipped with a 3/16 × 2 in (10.6 L:D), a 3/16 × 1 1/4 in (6.6 L:D) or a 3/16 × 1 3/4 in (9.3 L:D) with 30 sec conditioning retention time at 185°F with designated production rate. These processing conditions were used to create the following RT treatments: 10.6 L:D with 4.3 sec RT, 10.6 L:D with 2.9 sec RT, 9.3 L:D with 1.7 sec RT, 9.3 L:D with 1.1 sec RT, 6.6 L:D with 2.6 sec RT, and 6.6 L:D with 1.6 sec RT. The pellet mills were run 3 separate times to provide 3 replicates for each treatment. There was an overall effect (P < 0.001) of treatment on phytase stability in cooled pellets. When using the 1012 PM, phytase was more stable regardless of die retention time when diets were manufactured using the 6.6 L:D die compared to the 10.6 L:D die (P < 0.05). The hot pellet temperature of 10.6 L:D die was 195–211°F, while 6.6 L:D die was 184–189°F. However, the phytase stability was similar between the feed pelleted with 1012 PM equipped with 6.6 L:D die and the 3016 PM equipped with 9.3 L:D regardless of retention time (P > 0.05). The hot pellet temperature of feed pelleted with the 1012 PM equipped with 6.6 L:D die was 184–189°F, while the feed pelleted with the 3016 die equipped with 9.3 L:D die was 180–183°F. There was also a quadratic decrease in phytase stability as the die L:D increased (P < 0.0001). There- fore, the pellet mill size or die retention time did not affect phytase stability when the hot pellet temperature was less than 189°F. Pellet quality
- Open Access
- 1 January 2019
- Published by Kansas State University in Kansas Agricultural Experiment Station Research Reports
- Vol. 5 (8) , 35
The Effects of Filter Type and Warm-Up Time on Pellet Durability Index Using the Holmen NHP100 Portable Pellet Tester
The Holmen NHP100 (TekPro Ltd, Norfolk, UK) is a portable forced air pellet tester commonly used by the feed industry to determine the pellet durability index (PDI). The objective of this study was to determine the effect of filter type and machine warm-up time on PDI. A corn-soybean meal-based grower diet was conditioned at 185°F for 30 sec and subsequently pelleted using a laboratory pellet mill (Model CL5 California Pellet Mill Co., Crawfordsville, IN) equipped with a 0.16- × 0.5-in die. Production rate was 120 lb/h. Once cool, pellets were analyzed for PDI using the NHP100 with a 60-sec run time. Air temperature and pressure within the NHP100 were recorded throughout the experiment. Treatments were arranged in a 3 × 8 factorial with varying filters (none, factory tissue filter, or commercial paper towel filter) and machine warm-up time (0, 3, 6, 9, 12, 15, 18, or 21 min). There were three replicates per treatment. Pellets were sifted before and after analysis for separation of fines and pellets using a U.S. #6 standard sieve. There was a filter × warm-up time interaction (P ≤ 0.05) for air temperature. The air temperature without warm-up time (0 min) was greater with the factory filter and paper towel compared to no filter. Air temperature remained similar regardless of filter type as the warm-up time increased from 6 to 21 min There was a filter × warm-up time interaction (P ≤ 0.05) for air pressure. At 0 min warm-up time, there were no differences in air pressure between none, factory and paper towel filters. At 3 to 21 min warm-up time, air pressure remained similar between factory and paper towel filters, while no filter was greater than the paper towel filter. There was a filter × warm-up time interaction (P ≤ 0.05) for PDI. For no filter, increasing warm-up time from 0 to 6 min increased PDI with no further increase from 6 to 21 min. However, there were no differences in PDI with increasing warm-up time when using the factory filter or paper towel. Using the factory filter or paper towel had similar PDI, but resulted in greater PDI compared to no filter. In conclusion, warm-up time did not influence air temperature, pressure, or PDI when using a filter. Therefore, it is suggested to use a filter when conducting PDI analysis using the Holmen NHP 100.
- 1 January 2019
- Published by Kansas State University in Kansas Agricultural Experiment Station Research Reports
- Vol. 5 (8) , 35
Open AccessThe Effects of Filter Type and Warm-Up Time on Pellet Durability Index Using the Holmen NHP100 Portable Pellet Tester
The Holmen NHP100 (TekPro Ltd, Norfolk, UK) is a portable forced air pellet tester commonly used by the feed industry to determine the pellet durability index (PDI). The objective of this study was to determine the effect of filter type and machine warm-up time on PDI. A corn-soybean meal-based grower diet was conditioned at 185°F for 30 sec and subsequently pelleted using a laboratory pellet mill (Model CL5 California Pellet Mill Co., Crawfordsville, IN) equipped with a 0.16- × 0.5-in die. Production rate was 120 lb/h. Once cool, pellets were analyzed for PDI using the NHP100 with a 60-sec run time. Air temperature and pressure within the NHP100 were recorded throughout the experiment. Treatments were arranged in a 3 × 8 factorial with varying filters (none, factory tissue filter, or commercial paper towel filter) and machine warm-up time (0, 3, 6, 9, 12, 15, 18, or 21 min). There were three replicates per treatment. Pellets were sifted before and after analysis for separation of fines and pellets using a U.S. #6 standard sieve. There was a filter × warm-up time interaction (P ≤ 0.05) for air temperature. The air temperature without warm-up time (0 min) was greater with the factory filter and paper towel compared to no filter. Air temperature remained similar regardless of filter type as the warm-up time increased from 6 to 21 min There was a filter × warm-up time interaction (P ≤ 0.05) for air pressure. At 0 min warm-up time, there were no differences in air pressure between none, factory and paper towel filters. At 3 to 21 min warm-up time, air pressure remained similar between factory and paper towel filters, while no filter was greater than the paper towel filter. There was a filter × warm-up time interaction (P ≤ 0.05) for PDI. For no filter, increasing warm-up time from 0 to 6 min increased PDI with no further increase from 6 to 21 min. However, there were no differences in PDI with increasing warm-up time when using the factory filter or paper towel. Using the factory filter or paper towel had similar PDI, but resulted in greater PDI compared to no filter. In conclusion, warm-up time did not influence air temperature, pressure, or PDI when using a filter. Therefore, it is suggested to use a filter when conducting PDI analysis using the Holmen NHP 100.
- Open Access
- 1 January 2019
- Published by Kansas State University in Kansas Agricultural Experiment Station Research Reports
- Vol. 5 (8) , 37
The Effect of Pellet Mill Production Rate and Knife Distance on Pellet Quality
Longer pellet lengths may lead to decreased pellet breakage, resulting in increased pellet durability index (PDI). Thus, the objective of this experiment was to determine the effects of production rate and knife distance on pellet length and subsequent pellet quality. Treatments were arranged in a 2 × 3 factorial with two production rates (16 and 33 lb/min) and three knife distances (0.25, 0.50, and 0.75 in). All diets were conditioned at 185°F and pelleted using a CPM pellet mill (Model 1012-2 HD, California Pellet Mill Co., Crawfordsville, IN) equipped with a 0.19 in × 1.25 in die. The production rate (PR) and knife distance (KD) were randomized to minimize the effects of pelleting and sampling order. There were 3 replicates per treatment. Samples were analyzed for pellet length, percentage fines, and PDI using the standard and modified tumble box method (STD and MOD, respectively) and Holmen NHP100 (TekPro Ltd, Norfolk, UK) with a 60-sec run time. Data were analyzed using the GLIMMIX procedure of SAS (v. 9.4, SAS Inst. Inc., Cary, NC). There was no evidence for an interaction between PR and KD for all analyzed variables (P > 0.24). The 16 lb/min PR yielded a longer pellet (P ≤ 0.05) compared to the 33 lb/min PR. The PR had no effect on percentage fines (P > 0.10); however, decreasing the PR tended to increase PDI regardless of analytical method (P ≤ 0.10). Increasing KD resulted in longer (P < 0.01) pellets and decreased (P < 0.01) percentage fines. Reducing KD to 0.25 in reduced PDI compared to 0.50 in and 0.75 in treatments, which yielded similar PDI. In conclusion, pellet quality can be improved by increasing the pellet length from 0.19 to 0.34 in (KD 0.25 and 0.75 in, respectively).
- 1 January 2019
- Published by Kansas State University in Kansas Agricultural Experiment Station Research Reports
- Vol. 5 (8) , 37
Open AccessThe Effect of Pellet Mill Production Rate and Knife Distance on Pellet Quality
Longer pellet lengths may lead to decreased pellet breakage, resulting in increased pellet durability index (PDI). Thus, the objective of this experiment was to determine the effects of production rate and knife distance on pellet length and subsequent pellet quality. Treatments were arranged in a 2 × 3 factorial with two production rates (16 and 33 lb/min) and three knife distances (0.25, 0.50, and 0.75 in). All diets were conditioned at 185°F and pelleted using a CPM pellet mill (Model 1012-2 HD, California Pellet Mill Co., Crawfordsville, IN) equipped with a 0.19 in × 1.25 in die. The production rate (PR) and knife distance (KD) were randomized to minimize the effects of pelleting and sampling order. There were 3 replicates per treatment. Samples were analyzed for pellet length, percentage fines, and PDI using the standard and modified tumble box method (STD and MOD, respectively) and Holmen NHP100 (TekPro Ltd, Norfolk, UK) with a 60-sec run time. Data were analyzed using the GLIMMIX procedure of SAS (v. 9.4, SAS Inst. Inc., Cary, NC). There was no evidence for an interaction between PR and KD for all analyzed variables (P > 0.24). The 16 lb/min PR yielded a longer pellet (P ≤ 0.05) compared to the 33 lb/min PR. The PR had no effect on percentage fines (P > 0.10); however, decreasing the PR tended to increase PDI regardless of analytical method (P ≤ 0.10). Increasing KD resulted in longer (P < 0.01) pellets and decreased (P < 0.01) percentage fines. Reducing KD to 0.25 in reduced PDI compared to 0.50 in and 0.75 in treatments, which yielded similar PDI. In conclusion, pellet quality can be improved by increasing the pellet length from 0.19 to 0.34 in (KD 0.25 and 0.75 in, respectively).
- Open Access
- 1 January 2019
- Published by Kansas State University in Kansas Agricultural Experiment Station Research Reports
- Vol. 5 (8) , 10
Effects of Spray-Dried Lactococcus-Based Fermentation Products on Growth Performance of Nursery Pigs
A total of 720 barrows (initially 13.0 lb; Line 200 × 400; DNA, Columbus, NE) from 2 study groups (360 pigs per study group), were used in a 42-d growth trial to test the effects of spray-dried Lactococcus-based fermentation products on nursery pig performance. There were 24 replications per treatment and 5 pigs per pen. For both experiments, pens of pigs were randomly allotted to 1 of 6 dietary treatments in a completely randomized design. There were six treatment diets fed in 3 phases. The positive control diet included zinc oxide (phase 1), zinc oxide + chlortetracycline (CTC; phase 2) while the negative control diet did not include zinc oxide or CTC. Treatment diets included the negative control + 1 of 4 fermentation products (C, D, E, or F) added at 5% of the diet. Phase 3 diets contained a common control diet fed to all pigs plus treatment diets (C, D, E, and F). Phase 1 and 2 diets were fed in pelleted form and phase 3 in mash form. From d 0 to 20, there was an overall treatment effect (P = 0.001) where pigs fed the positive control had increased (P < 0.05) d 20 weight, average daily gain (ADG), average daily intake (ADFI), and improved feed efficiency (F/G) compared to those fed the negative control and negative control + fermentation product. From d 20 to 42, there was an overall treatment effect (P = 0.003) for F/G where pigs fed the negative control had improved (P < 0.05) F/G compared to those fed additive D, E, and F. Overall, there was a treatment effect (P = 0.03) for pigs fed the positive control having improved (P < 0.05) ADG and F/G compared to the negative control and negative control + fermentation product. In addition, pigs fed the negative control had improved (P < 0.05) F/G compared to those fed additive D, E, and F. In conclusion, pigs fed the positive control (zinc + CTC) diet had improved performance compared to pigs fed the negative control with or without fermentation product.
- 1 January 2019
- Published by Kansas State University in Kansas Agricultural Experiment Station Research Reports
- Vol. 5 (8) , 10
Open AccessEffects of Spray-Dried Lactococcus-Based Fermentation Products on Growth Performance of Nursery Pigs
A total of 720 barrows (initially 13.0 lb; Line 200 × 400; DNA, Columbus, NE) from 2 study groups (360 pigs per study group), were used in a 42-d growth trial to test the effects of spray-dried Lactococcus-based fermentation products on nursery pig performance. There were 24 replications per treatment and 5 pigs per pen. For both experiments, pens of pigs were randomly allotted to 1 of 6 dietary treatments in a completely randomized design. There were six treatment diets fed in 3 phases. The positive control diet included zinc oxide (phase 1), zinc oxide + chlortetracycline (CTC; phase 2) while the negative control diet did not include zinc oxide or CTC. Treatment diets included the negative control + 1 of 4 fermentation products (C, D, E, or F) added at 5% of the diet. Phase 3 diets contained a common control diet fed to all pigs plus treatment diets (C, D, E, and F). Phase 1 and 2 diets were fed in pelleted form and phase 3 in mash form. From d 0 to 20, there was an overall treatment effect (P = 0.001) where pigs fed the positive control had increased (P < 0.05) d 20 weight, average daily gain (ADG), average daily intake (ADFI), and improved feed efficiency (F/G) compared to those fed the negative control and negative control + fermentation product. From d 20 to 42, there was an overall treatment effect (P = 0.003) for F/G where pigs fed the negative control had improved (P < 0.05) F/G compared to those fed additive D, E, and F. Overall, there was a treatment effect (P = 0.03) for pigs fed the positive control having improved (P < 0.05) ADG and F/G compared to the negative control and negative control + fermentation product. In addition, pigs fed the negative control had improved (P < 0.05) F/G compared to those fed additive D, E, and F. In conclusion, pigs fed the positive control (zinc + CTC) diet had improved performance compared to pigs fed the negative control with or without fermentation product.