Stanislav Brilkov
Stanislav Brilkov has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Alexandr Demyanenko
Department of Chemistry and Chemical Technology, M. Kozybayev North Kazakhstan University, Petropavlovsk 150000, Kazakhstan
2 shared publications - Dmitriy Alyoshin
Department of Chemistry and Chemical Technology, M. Kozybayev North Kazakhstan University, Petropavlovsk 150000, Kazakhstan
2 shared publications - Sergey Litvinov
«AVAGRO» LLP
2 shared publications - Vitaliy Tyukanko
Department of Chemistry and Chemical Technology, M. Kozybayev North Kazakhstan University, Petropavlovsk 150000, Kazakhstan
2 shared publications - Vladislav Semenyuk
Manash Kozybayev North Kazakhstan University NPLC
2 shared publications - Antonina Dyuryagina
Manash Kozybayev North Kazakhstan University
1 shared publication
Latest Publications
- Open Access
- 29 August 2024
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 4 (7 (130)) , 47-59
Identification of patterns of the stress-strain state of a standard plastic tank for liquid mineral fertilizers
In this study, using the method of probabilistic deterministic planning (PDP), the optimum design parameters of a standard polyethylene tank used worldwide for transporting liquid mineral fertilizers (LMF) were determined. By the finite element method, the effect of the density of liquid mineral fertilizer, tank wall thickness and four motion modes (braking, acceleration, jump and landing) on the strength of standard polyethylene tanks was studied. According to the results of the study, the five most informative areas in the tank design were identified, for which the values of maximum stresses (σmax) were obtained: filler neck, pockets, walls, tap-in points and wall transition to the tank roof. As the LMF density increases, σmax in the tank increases linearly. Increasing the tank wall thickness by 1.5 times reduces the maximum stresses by 30 to 50 %. It was found that motion mode has a significant effect on the stress-strain state of a standard tank. The “heaviest” mode for a standard tank is “braking”. The “acceleration” motion mode causes σmax of no more than 60 % of the “braking” mode values. The “lightest” mode is “landing”, in which σmax is no more than 28 % relative to “braking”. Based on the PDP method, equations were derived for calculating maximum stresses depending on LMF density, wall thickness and motion mode of the tank. Nomograms were built that make it possible to quickly determine the wall thickness of a standard tank without calculations, depending on external factors. The results of the study can be used in practice when designing safe and durable tanks for transporting liquid mineral fertilizers.
- 29 August 2024
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 4 (7 (130)) , 47-59
Open AccessIdentification of patterns of the stress-strain state of a standard plastic tank for liquid mineral fertilizers
In this study, using the method of probabilistic deterministic planning (PDP), the optimum design parameters of a standard polyethylene tank used worldwide for transporting liquid mineral fertilizers (LMF) were determined. By the finite element method, the effect of the density of liquid mineral fertilizer, tank wall thickness and four motion modes (braking, acceleration, jump and landing) on the strength of standard polyethylene tanks was studied. According to the results of the study, the five most informative areas in the tank design were identified, for which the values of maximum stresses (σmax) were obtained: filler neck, pockets, walls, tap-in points and wall transition to the tank roof. As the LMF density increases, σmax in the tank increases linearly. Increasing the tank wall thickness by 1.5 times reduces the maximum stresses by 30 to 50 %. It was found that motion mode has a significant effect on the stress-strain state of a standard tank. The “heaviest” mode for a standard tank is “braking”. The “acceleration” motion mode causes σmax of no more than 60 % of the “braking” mode values. The “lightest” mode is “landing”, in which σmax is no more than 28 % relative to “braking”. Based on the PDP method, equations were derived for calculating maximum stresses depending on LMF density, wall thickness and motion mode of the tank. Nomograms were built that make it possible to quickly determine the wall thickness of a standard tank without calculations, depending on external factors. The results of the study can be used in practice when designing safe and durable tanks for transporting liquid mineral fertilizers.
- Open Access
- 28 June 2024
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 3 (1 (129)) , 45-56
Optimization of polyethylene rotomolded tank design for storage of liquid mineral fertilizers by the Taguchi method
In this research, by using the finite element method, the effect of five parameters (density of a liquid mineral fertilizer (ρ), its temperature (T), tank wall thickness (L), spacing of stiffeners (K) and stiffeners height (h)) on the strength of standard polyethylene rotomolded tanks used for storage of liquid mineral fertilizers (LMF) was studied. Using the Taguchi method, it was found that these parameters are ranked according to the degree of their influence (in decreasing order) on: maximum stresses (r>L>h>T>K), maximum stresses in the tank walls (r>L>K>T>h) and deformations of the tank (for DX/DY: r>L>h>T>K and for DZ: r>L>h>K>T). Validation of the FEM strength calculations was carried out, which showed satisfactory convergence of the calculated and experimental values. Generalized equations are derived that describe the effect of all five studied parameters on P, PW and tank deformations (along the X, Y and Z axes). On the basis of the derived equations, a nomogram has been constructed, which makes it possible to choose the optimal wall thickness that will correspond to the LMF density and storage temperature. Applying the optimal wall thickness ensures a guaranteed service life of at least 50 years, minimizing the risk of environmental accidents caused by tank failure and the release of LMF and associated toxic substances into groundwater. This research offers valuable insights for designing safer and more durable storage tanks for liquid mineral fertilizers. As an optimal design of the tank for storing the most common fertilizer UAN-32 (Urea Ammonium Nitrate, 32 % nitrogen), with a density of 1.32 g/cm3 and at storage temperatures up to 40 °C, the following values of structural parameters are recommended: L=10 mm, K=38 mm, and h=4 mm
- 28 June 2024
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 3 (1 (129)) , 45-56
Open AccessOptimization of polyethylene rotomolded tank design for storage of liquid mineral fertilizers by the Taguchi method
In this research, by using the finite element method, the effect of five parameters (density of a liquid mineral fertilizer (ρ), its temperature (T), tank wall thickness (L), spacing of stiffeners (K) and stiffeners height (h)) on the strength of standard polyethylene rotomolded tanks used for storage of liquid mineral fertilizers (LMF) was studied. Using the Taguchi method, it was found that these parameters are ranked according to the degree of their influence (in decreasing order) on: maximum stresses (r>L>h>T>K), maximum stresses in the tank walls (r>L>K>T>h) and deformations of the tank (for DX/DY: r>L>h>T>K and for DZ: r>L>h>K>T). Validation of the FEM strength calculations was carried out, which showed satisfactory convergence of the calculated and experimental values. Generalized equations are derived that describe the effect of all five studied parameters on P, PW and tank deformations (along the X, Y and Z axes). On the basis of the derived equations, a nomogram has been constructed, which makes it possible to choose the optimal wall thickness that will correspond to the LMF density and storage temperature. Applying the optimal wall thickness ensures a guaranteed service life of at least 50 years, minimizing the risk of environmental accidents caused by tank failure and the release of LMF and associated toxic substances into groundwater. This research offers valuable insights for designing safer and more durable storage tanks for liquid mineral fertilizers. As an optimal design of the tank for storing the most common fertilizer UAN-32 (Urea Ammonium Nitrate, 32 % nitrogen), with a density of 1.32 g/cm3 and at storage temperatures up to 40 °C, the following values of structural parameters are recommended: L=10 mm, K=38 mm, and h=4 mm