Priscila Tiemi Higuti Do Nascimento
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Priscila Tiemi Higuti Do Nascimento has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Arno de Klerk
Department of Chemical and Materials Engineering University of Alberta Edmonton Alberta Canada
2 shared publications - Clarissa Fleury Rocha
Academic Department of Chemical and Biology, Federal University of Technology—Paraná, 4900 Deputado Heitor de Alencar Furtado Avenue, Curitiba 81280-340, PR, Brazil
1 shared publication - Elaine Cristina Lengowski
Faculty of Forestry Engineering, Federal University of Mato Grosso, 2367 Fernando Corrêa da Costa Street, Cuiabá 78060-900, MT, Brazil
1 shared publication - Eraldo Antonio Bonfatti Júnior
Faculty of Agronomic Sciences, São Paulo State University, 3780 Avenida Universitária, Botucatu 18610-034, SP, Brazil
1 shared publication - José Domingos Fontana
Academic Department of Chemical and Biology, Federal University of Technology—Paraná, 4900 Deputado Heitor de Alencar Furtado Avenue, Curitiba 81280-340, PR, Brazil
1 shared publication - Lina M. Yañez Jaramillo
Department of Chemical and Materials Engineering, University of Alberta, 9211–116th Street, Edmonton, AB T6G 1H9, Canada
1 shared publication
Latest Publications
- Open Access
High-Kappa Eucalyptus Kraft Pulp in a Biorefinery Context: Balancing Sugar Production with Fiber-Reinforcement Potential
To establish a biorefinery within kraft-pulp mills, the extraction of fermentable sugars must be balanced with the preservation of fiber quality for papermaking. This study investigates this trade-off by applying partial enzymatic hydrolysis to unbleached high-kappa eucalyptus kraft pulp to co-produce bioethanol and packaging-grade materials. Although the mass-transfer limitations inherent to the high-consistency strategy (15% solids or 150 g L−1) restrict extensive saccharification (keeping glucose conversion below 5% at 1.5 h), it naturally directs the process toward a low-severity regime essential for fiber conservation. Structural analysis (X-ray diffraction and microscopy) revealed that enzymes preferentially targeted amorphous regions, increasing crystallinity (from ≈74% to ≈82%) but reducing intrinsic fiber strength (tear) over time (dropping from ~5.6 to ~2.3 mN·m2·g−1 within 30 min). However, a strategic window for valorization has been identified. Instead of direct papermaking, hydrolyzed residue is highly effective as a strength-enhancing additive. When blended (20% w w−1) with commercial pulp, the modified fibers improved interfiber bonding, restored the tensile strength, and significantly increased the Burst Index (up to ~1.7 kPa·m2·g−1). These results demonstrate a viable industrial approach using partial hydrolysis to recover hemicellulose-based sugars for biofuels, while transforming the solid fraction into a high-performance reinforcement agent for paper packaging. This approach effectively converts a potential trade-off into a synergistic dual-product stream.
Open AccessHigh-Kappa Eucalyptus Kraft Pulp in a Biorefinery Context: Balancing Sugar Production with Fiber-Reinforcement Potential
To establish a biorefinery within kraft-pulp mills, the extraction of fermentable sugars must be balanced with the preservation of fiber quality for papermaking. This study investigates this trade-off by applying partial enzymatic hydrolysis to unbleached high-kappa eucalyptus kraft pulp to co-produce bioethanol and packaging-grade materials. Although the mass-transfer limitations inherent to the high-consistency strategy (15% solids or 150 g L−1) restrict extensive saccharification (keeping glucose conversion below 5% at 1.5 h), it naturally directs the process toward a low-severity regime essential for fiber conservation. Structural analysis (X-ray diffraction and microscopy) revealed that enzymes preferentially targeted amorphous regions, increasing crystallinity (from ≈74% to ≈82%) but reducing intrinsic fiber strength (tear) over time (dropping from ~5.6 to ~2.3 mN·m2·g−1 within 30 min). However, a strategic window for valorization has been identified. Instead of direct papermaking, hydrolyzed residue is highly effective as a strength-enhancing additive. When blended (20% w w−1) with commercial pulp, the modified fibers improved interfiber bonding, restored the tensile strength, and significantly increased the Burst Index (up to ~1.7 kPa·m2·g−1). These results demonstrate a viable industrial approach using partial hydrolysis to recover hemicellulose-based sugars for biofuels, while transforming the solid fraction into a high-performance reinforcement agent for paper packaging. This approach effectively converts a potential trade-off into a synergistic dual-product stream.
- 5 December 2025
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 39 (50) , 23567-23583
Thermal Conversion of Athabasca Bitumen under Low- and High-Pressure Conditions: Influence on Cracking, Hydrogen Transfer, and Addition Reactions
- 5 December 2025
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 39 (50) , 23567-23583
Thermal Conversion of Athabasca Bitumen under Low- and High-Pressure Conditions: Influence on Cracking, Hydrogen Transfer, and Addition Reactions
- Open Access
Fluorescence Spectroscopy Applied to Thermal Conversion of Bitumen
Phase instability that develops during thermal conversion of heavy oils and bitumen limits the extent of conversion in processes such as visbreaking. It was postulated that aromatic species with conjugated unsaturated systems extending beyond the aromatic rings likely contributed to reactions leading to phase instability, fouling, and coking. Many fluorophores have such conjugated π-electron systems. Three case studies were presented where products from thermal conversion were analyzed by fluorescence spectroscopy: (i) Cold Lake bitumen converted at 150–300 °C; (ii) asphaltenes depleted and enriched Athabasca bitumen converted at 380 °C; and (iii) Athabasca bitumen converted at 400 °C and 0.5–4.0 MPa. It was found that the fluorescence intensity of bitumen increased on thermal conversion. Fluorescence intensity increased in relation to reaction time for conversion at 150–300 °C, but it had a weak relationship with temperature. At 380 and 400 °C, this monotonic relationship was no longer apparent. There was no relationship with refractive index. Despite some overlap in fluorescence intensity values, 400 °C converted products obtained at 2.5–4.0 MPa had lower fluorescence intensity than products obtained at 0.5–2.0 MPa. Tentative explanations were offered for these observations. The change in fluorescence intensity with operating conditions and nature of the feed was consistent with the expected free radical concentration associated with the operating conditions and extent of hydrogen transfer. Although the study did not provide proof for the relationship between the fluorescence intensity and the concentration of aromatic species with conjugated unsaturated systems, the experimental observations were congruent with it.
Open AccessFluorescence Spectroscopy Applied to Thermal Conversion of Bitumen
Phase instability that develops during thermal conversion of heavy oils and bitumen limits the extent of conversion in processes such as visbreaking. It was postulated that aromatic species with conjugated unsaturated systems extending beyond the aromatic rings likely contributed to reactions leading to phase instability, fouling, and coking. Many fluorophores have such conjugated π-electron systems. Three case studies were presented where products from thermal conversion were analyzed by fluorescence spectroscopy: (i) Cold Lake bitumen converted at 150–300 °C; (ii) asphaltenes depleted and enriched Athabasca bitumen converted at 380 °C; and (iii) Athabasca bitumen converted at 400 °C and 0.5–4.0 MPa. It was found that the fluorescence intensity of bitumen increased on thermal conversion. Fluorescence intensity increased in relation to reaction time for conversion at 150–300 °C, but it had a weak relationship with temperature. At 380 and 400 °C, this monotonic relationship was no longer apparent. There was no relationship with refractive index. Despite some overlap in fluorescence intensity values, 400 °C converted products obtained at 2.5–4.0 MPa had lower fluorescence intensity than products obtained at 0.5–2.0 MPa. Tentative explanations were offered for these observations. The change in fluorescence intensity with operating conditions and nature of the feed was consistent with the expected free radical concentration associated with the operating conditions and extent of hydrogen transfer. Although the study did not provide proof for the relationship between the fluorescence intensity and the concentration of aromatic species with conjugated unsaturated systems, the experimental observations were congruent with it.
- 3 July 2024
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 38 (14) , 12632-12644
Effect of Pressure on Visbreaking Product Composition and Properties
- 3 July 2024
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 38 (14) , 12632-12644
Effect of Pressure on Visbreaking Product Composition and Properties