SPSreeni Poolakkal

Sreeni Poolakkal

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Sreeni Poolakkal has a total of 23 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • A Time-Domain RX for Reconfigurable Energy-Efficient Software-Defined Radios

    by Sreeni Poolakkal, Arpit Rao, Dipan Kar, Daniel Mazidi, Subhanshu Gupta

    Constant-field scaling results in a lower supply voltage ( $\rm V_{DD}$ ) as device length decreases, which benefits digital power consumption by improving the energy efficiency per operation and enabling higher functional density. While wireless receivers (RXs) benefit from the increased transition frequency ( $\rm f_{T}$ ), the reduced $\rm V_{DD}$ limits both linearity and signal swing, necessitating the realization of RX functionality across multiple supply domains. This article presents a reconfigurable RX architecture that distributes the overall gain between the voltage and time domains, effectively decoupling gain dependency from $\rm V_{DD}$ . A double sampler is introduced to confine the signal swing within the linear region of the RX, thereby relaxing linearity requirements for subsequent time-domain processing. The combination of double sampling and time-domain processing enables a unique two-stage, reconfigurable, second-order filtering response that enhances out-of-band (OOB) blocker rejection. The time-domain processing not only enhances in-band signal tolerance but can also be dynamically reconfigured to provide additional amplification, band-edge droop correction, and filtering. Implemented in TSMC 65-nm CMOS, the proposed RX operates across 1.9–4 GHz, achieves a $\approx 6$ -MHz baseband bandwidth with robust +10-dBm OOB IIP3, and occupies only 0.71 mm2 while consuming 18 mW.

  • Open Access

    Dynamic beam-stabilized, additive-printed flexible antenna arrays with on-chip rapid insight generation

    by Sreeni Poolakkal, Abdullah Islam, Arpit Rao, Shrestha Bansal, Ted Dabrowski, Kalsi Kwan, Zhongxuan Wang, Amit Kumar Mishra, Julio A. Navarro, Shenqiang Ren, et al.

    Conformal phased arrays promise shape-changing properties, multiple degrees of freedom in the scan angle, and applications for edge computing, including devices for wearable, airborne, and seaborne platforms. However, they have suffered from two critical limitations. (1) Although most applications require on-the-move communication and sensing, prior conformal arrays have suffered from dynamic deformation-induced beam pointing errors. This work introduces a dynamic beam-stabilized processor capable of beam adaptation through on-chip real-time control of fundamental gain, phase, and delay for each element. (2) Prior conformal arrays have leveraged additive printing to enhance flexibility, but conventional printable inks based on silver are expensive, and those based on copper suffer from spontaneous metal oxidation that alters trace impedance and degrades beamforming performance. Instead, we leverage a low-cost copper molecular decomposition ink with < 0.1% variation per °C across temperature and strain, and corrects any residual deformity in real-time using the dynamic beam-stabilized processor. Demonstrating unified material and physical deformation correction, our silicon-integrated dynamic beam-stabilized processor is low-power, low-area, and easily scalable due to tile-based architecture, thereby ideal for on-device implementations.


  • A Four-Element True-Time-Delay Slice-Based Receiver Array for FR3 Upper Mid-Band Wireless

    by Hesam Abbasi, Adam Slater, Foad Beheshti, Sreeni Poolakkal, Subhanshu Gupta

    A continuous beam angle resolution enables precise beam steering and prevents beam squinting, especially in dense environments where large arrays create narrow beams to maximize capacity. This work proposes a continuous beam angle reconfigurable four-element receiver (RX) for the FR3 frequency band. The implemented vector modulator (VM) phase-shifting mechanism is based on the slice-based RX for the coarse stage and phase-shifting polyphase filters (PPFs) in the local oscillator (LO) paths for the fine stage to overcome the limited phase resolution. The beamformer is equipped with current-mode true-time delay (TTD) units to further assist with better linearity performance and signal-to-noise ratio (SNR) improvement at the band edges. Fabricated in TSMC 65-nm complementary metal-oxide–semiconductor (CMOS), the prototype occupies an area of 1.65 mm2, consuming 14 mA/element centered at 7.5GHz. The measured maximum single-channel gain is 22 dB, with a minimum noise figure (NF) of 7.48 dB while having an $S_{11}\lt -10$ dB across 7.28–7.78-GHz input frequency span. A root mean square (rms) phase error of 0.76° is achieved while showing continuous phase shifting over 360°. The TTD units improve the beamformed down-converted 100-MHz wideband (WB) up to 1.5-dB gain at the band edge. Moreover, over-the-air (OTA) measurements show the reception of a single-tone signal at a 297.88-cm distance between RX and a horn antenna.


  • Open Access

    Dynamic Beam-Stabilized, Additive-Printed Flexible Antenna Arrays with On-Chip Rapid Insight Generation

    by Sreeni Poolakkal, Abdullah Islam, Arpit Rao, Shrestha Bansal, Ted Dabrowski, Kalsi Kwan, Zhongxuan Wang, Amit Mishra, Julio Navarro, Shenqiang Ren, et al.

    Conformal phased arrays promise shape-changing properties, multiple degrees of freedom to the scan angle, and novel applications in wearables, aerospace, defense, vehicles, and ships. However, they have suffered from two critical limitations. (1) Although most applications require on-the-move communication and sensing, prior conformal arrays have suffered from dynamic deformation-induced beam pointing errors. We introduce a Dynamic Beam-Stabilized (DBS) processor capable of beam adaptation through on-chip real-time control of fundamental gain, phase, and delay for each element. (2) Prior conformal arrays have leveraged additive printing to enhance flexibility, but conventional printable inks based on silver are expensive, and those based on copper suffer from spontaneous metal oxidation that alters trace impedance and degrades beamforming performance. We instead leverage a low-cost Copper Molecular Decomposition (CuMOD) ink with < 0.1% variation per ◦C with temperature and strain and correct any residual deformity in real-time using the DBS processor. Demonstrating unified material and physical deformation correction, our CMOS DBS processor is low-power, low-area, and easily scalable due to a tile architecture, thereby ideal for on-device implementations.

  • Enhancing Continuous Beam Angle Resolution for Next Generation Wireless Systems: A Multi-Stage Phase-Shifting Polyphase Filters Approach

    by Adam Slater, Hesam Abbasi, Sreeni Poolakkal, Foad Beheshti, Subhanshu Gupta

    Increasing user density and capacity in next-generation systems presents a need for fine beam angle resolution especially in the emerging upper mid-band $7-24$ GHz frequency regime. This paper presents a scalable area- and energy-efficient quadrature generator targeted for beamforming receivers with a multi-stage phase-shifting polyphase filter providing continuous beam angle resolution. When complemented with vector modulation for coarse tuning, a phase range of 360° is achieved realizing a phase-shifter-less implementation leveraging slice-based receiver architecture and polyphase filters. Fabricated in 65nm CMOS, the phase-shifting polyphase filter occupies 0.003 mm2, consumes 0.25 mW, and achieves an Image Rejection Ratio >58 dB over the entire phase range. The quadrature generator is demonstrated with a proof-of-concept receiver array operating between 7.28-7.78 GHz consuming 37 mW per element occupying 1.26 mm2.