Alexander Melnikov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Alexander Melnikov has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Alexandr Isaev
Valiev Institute of Physics and Technology, Russian Academy of Sciences, Moscow, Russia
1 shared publication - Andrey V. Miakonkikh
National Research Center “Kurchatov Institute”—Valiev Division of Physical and Technological Research, 36/1, Nakhimovsky Avenue, 117218 Moscow, Russia
1 shared publication Eugenii Soldatov
Lomonosov Moscow State University Faculty of Physics, Moskva, Moskva, RUSSIAN FEDERATION
1 shared publication- Iren E. Kuznetsova
Kotelnikov Institute of Radio Engineering and Electronics of RAS, Moscow 125009, Russia
1 shared publication - Sarkis Dagesyan
M.V. Lomonosov Moscow State Univ. (Russian Federation)
1 shared publication - Vitaly Kuzmenko
NRC “Kurchatov Institute”—Valiev IPT, Nakhimovsky Prospect, 36/1 , Moscow 117218
1 shared publication
Latest Publications
- 15 July 2024
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 42 (5)
Revealing the controlling mechanisms of atomic layer etching for high-k dielectrics in conventional inductively coupled plasma etching tool
The possibilities of optimization of the two-step atomic layer etching process for HfO2 in conventional plasma etching tools were studied. The surface modification step was realized in Ar/CF4/H2 plasma, and the reaction between the modified layer and the surface was activated by Ar ion bombardment from the plasma in the second step. Investigation of the effects of activation step duration, DC bias during activation, and Ar plasma density was carried out. The mechanism of the etching process has been shown to involve fluorination of oxide during the modification step and subsequent removal of fluorine-containing particles at the activation step. An increase in parasitic sputtering rate and lower process saturation with the growth of DC bias during activation was demonstrated. The advantage of the ALE process in lower surface roughness over the conventional etching process was shown. Similar etching characteristics of HfO2 and ZrO2 suggest a similarity in the etching process for the mixed hafnium-zirconium oxide material.
- 15 July 2024
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 42 (5)
Revealing the controlling mechanisms of atomic layer etching for high-k dielectrics in conventional inductively coupled plasma etching tool
The possibilities of optimization of the two-step atomic layer etching process for HfO2 in conventional plasma etching tools were studied. The surface modification step was realized in Ar/CF4/H2 plasma, and the reaction between the modified layer and the surface was activated by Ar ion bombardment from the plasma in the second step. Investigation of the effects of activation step duration, DC bias during activation, and Ar plasma density was carried out. The mechanism of the etching process has been shown to involve fluorination of oxide during the modification step and subsequent removal of fluorine-containing particles at the activation step. An increase in parasitic sputtering rate and lower process saturation with the growth of DC bias during activation was demonstrated. The advantage of the ALE process in lower surface roughness over the conventional etching process was shown. Similar etching characteristics of HfO2 and ZrO2 suggest a similarity in the etching process for the mixed hafnium-zirconium oxide material.
- 21 January 2020
- Published by IOP Publishing in Nanotechnology
- Vol. 31 (14) , 145205
Influence of plate acoustic waves on electronic transport in nanowires
The acoustoelectric effect is the generation of a acoustoelectric current in a non-biased device by a piezoactive acoustic wave. This effect has recently attracted the attention of researchers as a possible method to control the motion of massive objects in the quantum regime. We suggest using this effect for development of highly sensitive nanoelectronic sensors. The sensitivity could be increased through the use of modulation mode of operation based on the acoustic pilot signal and the transition from quasi-stationary measurement to measurement at the modulation frequency. The acoustic delay line based on shear-horizontal acoustic wave of zero order (SH 0 ) with resonant frequency 3.25 MHz in Y-X LiNbO 3 plate was produced. The nanostructure consisting of nanowire with size 20 nm × 180 nm was placed in the center between IDTs. The current–voltage characteristics of this nanowire in the presence and absence of the acoustic wave were meazured by a picoampermeter. The analysis has shown that the presence of piezoactive acoustic wave is influenced by electric current in a nanowire.
- 21 January 2020
- Published by IOP Publishing in Nanotechnology
- Vol. 31 (14) , 145205
Influence of plate acoustic waves on electronic transport in nanowires
The acoustoelectric effect is the generation of a acoustoelectric current in a non-biased device by a piezoactive acoustic wave. This effect has recently attracted the attention of researchers as a possible method to control the motion of massive objects in the quantum regime. We suggest using this effect for development of highly sensitive nanoelectronic sensors. The sensitivity could be increased through the use of modulation mode of operation based on the acoustic pilot signal and the transition from quasi-stationary measurement to measurement at the modulation frequency. The acoustic delay line based on shear-horizontal acoustic wave of zero order (SH 0 ) with resonant frequency 3.25 MHz in Y-X LiNbO 3 plate was produced. The nanostructure consisting of nanowire with size 20 nm × 180 nm was placed in the center between IDTs. The current–voltage characteristics of this nanowire in the presence and absence of the acoustic wave were meazured by a picoampermeter. The analysis has shown that the presence of piezoactive acoustic wave is influenced by electric current in a nanowire.