LLLang Lin

Lang Lin

*This is an algorithmically generated author record based on publicly available information.

Lang Lin has a total of 15 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Late Breaking Results: Toward a Foundation Model for 3DIC Thermal Analysis and Beyond

    by Akhilesh Kumar, Zelin Lu, Norman Chang, Igor L. Markov, Lang Lin, Jessica Yen, Haoliang Jiang, Wenbo Xia, Yujing Luo, Gang Qu

  • Open Access

    Mechanical, workability, economic and environmental properties of concrete with limestone calcined clay cement and recycled aggregates

    by Yong Yu, Mingjian Yang, Cheng Wan, Lang Lin

    Limestone calcined clay cement (LC3) and recycled aggregates (RAs) are important innovations in civil engineering, offering solutions to the industry’s energy and carbon challenges. However, limited research on their combined use has hindered widespread application. This study systematically evaluates LC3-based concrete with both coarse and fine RAs, using material testing, cost analysis and carbon footprint assessments to examine the effects of water-to-binder ratio, metakaolin-limestone powder synergy, RA content and particle quality on workability, compressive strength, elastic modulus, splitting-tensile strength, unit cost and environmental impact, while establishing clear quantitative relationships. Key findings include: (i) Using up to 50% metakaolin-limestone powder by mass, 30% coarse RA and 20% recycled sand by volume results in minimal reductions in 28-day strength and elastic modulus. However, exceeding 70%, 50% and 40%, respectively, leads to significant mechanical deterioration. (ii) LC3 concrete has 4-15% lower strength than Portland cement concrete at 14 days due to slower pozzolanic reactions, but strength levels equalize by 28 days. Similarly, recycled aggregate concrete shows lower early-age strength, with extended curing further highlighting performance differences, likely due to the residual mortar on recycled particles. (iii) Lifecycle analysis confirms that replacing 50% of the binder with metakaolin-limestone powder reduces carbon emissions by 29.9% and costs by 12.4% for strength-equivalent concrete. In contrast, RAs offer only modest sustainability benefits, with 20% recycled sand and 30% coarse RA increasing emissions by 5.4% and 2.8%, respectively, while keeping costs stable. (iv) The quality of RA particles plays a key role in their sustainable application. Additionally, transportation distance significantly affects the circular benefits of RA use but has a limited impact on the sustainability of metakaolin-limestone powder.


  • Open Access

    Water permeability property of recycled aggregate concrete

    by Yong Yu, Jialiang Yuan, Lang Lin

    Recycled aggregate concrete (RAC) is widely recognized as a promising approach for recycling construction and demolition waste. However, its practical application remains limited. A contributing factor to this limitation is the incomplete understanding of RAC’s durability characteristics, particularly its permeability, which is closely tied to the transport of harmful ions within the concrete matrix. Despite the critical importance of this issue, research in this area is still relatively sparse. This knowledge gap has motivated the current study, which seeks to thoroughly investigate the water permeability properties of RAC. In this comprehensive study, 84 specimens were fabricated for permeability testing. This study explores the influence of various factors, including the sources of coarse and fine recycled aggregates (RAs), the RA replacement ratios, and the water-to-binder ratio. The results indicate that the inclusion of both coarse and fine RAs reduces the impermeability of concrete. However, enhancing the quality of these RAs—specifically by increasing the compressive strength of the source concrete—can mitigate the reduction in impermeability. A statistical relationship is established between the average and maximum water permeation depths measured during permeability testing, leading to the formulation of a correlation between the permeability coefficient and the impermeability grade of RAC. Furthermore, mercury intrusion porosimetry testing was conducted to quantitatively analyze the pore structure of the mortar in RAC, providing a microscopic perspective that explains the macroscopic permeability behavior observed. Finally, a predictive model for estimating the permeability coefficient of RAC is proposed, demonstrating a high level of accuracy.


  • Open Access

    Compressive stress–strain relationship and its variability of basalt fiber reinforced recycled aggregate concrete

    by Yong Yu, Lingzhu Zhou, Lang Lin

    Basalt fiber reinforced recycled aggregate concrete (BFRAC) is a high-performance, environmentally friendly material that combines lightweight, high-strength fibers with low-carbon recycled aggregates (RAs), positioned for extensive use in building structures. However, research on its constitutive relationships is currently scarce, which partly restricts component design and analysis. In this context, the current study thoroughly explores the stress–strain relationship and variability of BFRAC under compression, using 240 cylinders for testing to investigate the influence of factors like coarse/fine RA sources, RA replacement rates, and fiber dosage. The study found that the addition of RAs and fibers reduced the workability of the mixture, particularly with the inclusion of fine RAs and short-cut fibers. Using coarse and fine RAs generally reduces the material’s elastic modulus, compressive strength, and post-peak ductility. Adding fibers can slightly improve compressive strength and peak strain, significantly reduce material brittleness, and have a minimal impact on elastic modulus. Importantly, the study noted that the pre-peak segment of the stress–strain curve of BFRAC is most sensitive to the addition of fine RAs, while the post-peak segment is most sensitive to fiber content. Despite this, using high-quality RAs up to 50% replacement and adding 0.4% by volume of fiber can make BFRAC with mechanical properties comparable to natural aggregate concrete. Based on the observed tests, this paper proposes constitutive relationships that incorporate skeleton curves and variability at different points for the compressive stress–strain behavior of BFRAC.