Tanawan Wannawong
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Tanawan Wannawong has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Chawakorn Rewtragulpaibul
Royal Irrigation Department, Ministry of Agriculture and Cooperatives, Bangkok 10300, Thailand
3 shared publications - Peerawat Puengpapat
Royal Irrigation Department, Ministry of Agriculture and Cooperatives, Bangkok 10300, Thailand
2 shared publications - Saravut Jaritngam
Faculty of Engineering, Prince of Songkla University, Songkhla 90110, Thailand
2 shared publications - Opas Somchainuek
Department of Highways, Ministry of Transport, Songkhla 90000, Thailand
1 shared publication - Saravut Jaritngam
Faculty of Engineering, Prince of Songkla University, Songkhla 90110, Thailand
1 shared publication
Latest Publications
- Open Access
Feasibility and Performance Evaluation of Asphalt Concrete Cores for Rockfill Dams
This study investigated the potential use of asphalt concrete produced with locally sourced limestone and granite aggregates as an impervious core material in rockfill dams. An independent laboratory program evaluated 16 mixture conditions comprising two aggregate types, asphalt cement contents of 6% and 7%, and nominal target air-void contents of 1–4%. Marshall, hydraulic-conductivity, and consolidated-undrained triaxial tests were conducted to characterize the mixtures. The reported hydraulic conductivity ranged from 2.9549 × 10−10 to 3.8887 × 10−5 cm/s, while effective cohesion and friction angle ranged from 165.7 to 540.3 kPa and 34.07° to 55.61°, respectively. Four core-property datasets corresponding to a 2% target air-void content were evaluated using two-dimensional GeoStudio analyses under steady-state and rapid-drawdown conditions. Steady-state seepage discharge ranged from 1.967 × 10−9 to 6.7191 × 10−6 m3/s, with downstream global factors of safety of 2.209–2.215. The upstream global factor of safety at Day 7 of rapid drawdown was 2.041 for all four datasets. The granite mixture containing 7% asphalt cement and a target air-void content of 2% (Granite AC7% AV2%) was subsequently selected as a representative, rather than optimal, core-property dataset for a separate steady-state geometry comparison. Relative to the conventional clay-core baseline, a 0.50-m-thick asphalt concrete core with shell slopes of 1 V:1.5 H and 1 V:1.4 H reduced the calculated embankment volume per unit dam length by 21.11% and 24.83%, respectively, with corresponding global factors of safety of 1.655 and 1.557. A supplementary rapid-drawdown assessment of the steepest alternative yielded an upstream global factor of safety of 1.473 at Day 6, the lowest among the reported daily results. The findings provide comparative laboratory data and case-specific numerical results for preliminary assessment of asphalt concrete dam cores. Hydraulic acceptance and field-scale suitability are not established, and further experimental verification and numerical sensitivity assessments remain necessary before application.
Open AccessFeasibility and Performance Evaluation of Asphalt Concrete Cores for Rockfill Dams
This study investigated the potential use of asphalt concrete produced with locally sourced limestone and granite aggregates as an impervious core material in rockfill dams. An independent laboratory program evaluated 16 mixture conditions comprising two aggregate types, asphalt cement contents of 6% and 7%, and nominal target air-void contents of 1–4%. Marshall, hydraulic-conductivity, and consolidated-undrained triaxial tests were conducted to characterize the mixtures. The reported hydraulic conductivity ranged from 2.9549 × 10−10 to 3.8887 × 10−5 cm/s, while effective cohesion and friction angle ranged from 165.7 to 540.3 kPa and 34.07° to 55.61°, respectively. Four core-property datasets corresponding to a 2% target air-void content were evaluated using two-dimensional GeoStudio analyses under steady-state and rapid-drawdown conditions. Steady-state seepage discharge ranged from 1.967 × 10−9 to 6.7191 × 10−6 m3/s, with downstream global factors of safety of 2.209–2.215. The upstream global factor of safety at Day 7 of rapid drawdown was 2.041 for all four datasets. The granite mixture containing 7% asphalt cement and a target air-void content of 2% (Granite AC7% AV2%) was subsequently selected as a representative, rather than optimal, core-property dataset for a separate steady-state geometry comparison. Relative to the conventional clay-core baseline, a 0.50-m-thick asphalt concrete core with shell slopes of 1 V:1.5 H and 1 V:1.4 H reduced the calculated embankment volume per unit dam length by 21.11% and 24.83%, respectively, with corresponding global factors of safety of 1.655 and 1.557. A supplementary rapid-drawdown assessment of the steepest alternative yielded an upstream global factor of safety of 1.473 at Day 6, the lowest among the reported daily results. The findings provide comparative laboratory data and case-specific numerical results for preliminary assessment of asphalt concrete dam cores. Hydraulic acceptance and field-scale suitability are not established, and further experimental verification and numerical sensitivity assessments remain necessary before application.
- Open Access
- 12 May 2026
- Published by MDPI AG in Preprints.org
Feasibility and Performance Evaluation of Asphalt Concrete Cores for Rockfill Dams
This study evaluates the feasibility of using asphalt concrete as an impermeable core material for rockfill dams under tropical conditions. Laboratory testing and numerical modeling were conducted to assess the hydraulic and mechanical performance of asphalt concrete mixtures produced with locally available aggregates in Thailand. Asphalt mixtures were designed using the Marshall method with asphalt binder contents of 6% and 7% and target air void contents between 1-4%. Laboratory testing included permeability testing, Marshall stability testing, and triaxial compression tests to determine hydraulic conductivity, shear strength parameters, and deformation characteristics. Results show that asphalt concrete mixtures with air void contents below 1% exhibit extremely low permeability, with hydraulic conductivity on the order of 10⁻¹¹–10⁻¹² m/s, satisfying requirements for impervious dam cores. Triaxial compression tests yielded cohesion values between 97-572 kPa and friction angles ranging from 31° to 52°, indicating adequate shear resistance. Numerical simulations performed using GeoStudio compared rockfill dams with asphalt concrete cores and conventional clay cores. The results demonstrate that a 0.5‑m‑thick asphalt concrete core provides comparable seepage control and slope stability while requiring significantly smaller material volume. The findings suggest that asphalt concrete cores represent a technically feasible and economically advantageous alternative to clay cores, particularly in regions where suitable clay materials are limited.
- 12 May 2026
- Published by MDPI AG in Preprints.org
Open AccessFeasibility and Performance Evaluation of Asphalt Concrete Cores for Rockfill Dams
This study evaluates the feasibility of using asphalt concrete as an impermeable core material for rockfill dams under tropical conditions. Laboratory testing and numerical modeling were conducted to assess the hydraulic and mechanical performance of asphalt concrete mixtures produced with locally available aggregates in Thailand. Asphalt mixtures were designed using the Marshall method with asphalt binder contents of 6% and 7% and target air void contents between 1-4%. Laboratory testing included permeability testing, Marshall stability testing, and triaxial compression tests to determine hydraulic conductivity, shear strength parameters, and deformation characteristics. Results show that asphalt concrete mixtures with air void contents below 1% exhibit extremely low permeability, with hydraulic conductivity on the order of 10⁻¹¹–10⁻¹² m/s, satisfying requirements for impervious dam cores. Triaxial compression tests yielded cohesion values between 97-572 kPa and friction angles ranging from 31° to 52°, indicating adequate shear resistance. Numerical simulations performed using GeoStudio compared rockfill dams with asphalt concrete cores and conventional clay cores. The results demonstrate that a 0.5‑m‑thick asphalt concrete core provides comparable seepage control and slope stability while requiring significantly smaller material volume. The findings suggest that asphalt concrete cores represent a technically feasible and economically advantageous alternative to clay cores, particularly in regions where suitable clay materials are limited.
- Open Access
- 26 July 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (15) , 6555
Comparison of Embankment Properties with Clay Core and Asphaltic Concrete Core
The development of a country is affected by various multifaceted factors, which are likely to generate the highest benefits. For example, developing water resources by constructing embankments to store water and for transportation must consider high resilience, particularly with the current challenges arising from climate change. Another factor that must be considered is the shortage of essential materials for embankment cores, such as clay, which is the primary material for constructing such cores. This study aims to analyze the stability of soil embankments between the change of materials, namely clay and asphaltic concrete, by varying the water level and increasing the embankment load. The result shows that the asphaltic concrete core exhibits a significantly higher stability than the clay core, such as its reduced water seepage and lower deformation. In the worst-case scenario, the asphalt concrete core has a thickness of 0.3 m and a seepage rate of 15.1 × 10−4 m3/day. Comparatively, the seepage rate of the clay core is approximately 10-times lower.
- 26 July 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (15) , 6555
Open AccessComparison of Embankment Properties with Clay Core and Asphaltic Concrete Core
The development of a country is affected by various multifaceted factors, which are likely to generate the highest benefits. For example, developing water resources by constructing embankments to store water and for transportation must consider high resilience, particularly with the current challenges arising from climate change. Another factor that must be considered is the shortage of essential materials for embankment cores, such as clay, which is the primary material for constructing such cores. This study aims to analyze the stability of soil embankments between the change of materials, namely clay and asphaltic concrete, by varying the water level and increasing the embankment load. The result shows that the asphaltic concrete core exhibits a significantly higher stability than the clay core, such as its reduced water seepage and lower deformation. In the worst-case scenario, the asphalt concrete core has a thickness of 0.3 m and a seepage rate of 15.1 × 10−4 m3/day. Comparatively, the seepage rate of the clay core is approximately 10-times lower.