Gaël Marnier
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Gaël Marnier has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Cendrine Folton
Laboratoire de Cristallographie et Sciences des Matériaux, University of Caen Normandie, Normandie Université, CNRS, 6 Bd Maréchal Juin, 14000 Caen, France
1 shared publication - Clément Keller
Laboratoire Génie de Production, Université de Technologie de Tarbes Occitanie Pyrénées, Avenue d’Azereix, 65000 Tarbes, France
1 shared publication - Eric Hug
CRISMAT Laboratory, UNICAEN—Normandy University, UMR CNRS 6508, Boulevard Maréchal Juin, 14000 Caen, France
1 shared publication - Jade Papin
Laboratoire de Cristallographie et Sciences des Matériaux, University of Caen Normandie, Normandie Université, CNRS, 6 Bd Maréchal Juin, 14000 Caen, France
1 shared publication - Kostiantyn Tabalaiev
CRMC, Industeel, 56 rue Clémenceau, 71202 Le Creusot, France
1 shared publication
Latest Publications
- Open Access
Ultrafine Grain 316L Stainless Steel Manufactured by Ball Milling and Spark Plasma Sintering: Consequences on the Corrosion Resistance in Chloride Media
This paper reports experimental results concerning the corrosion of 316L austenitic stainless steels produced by ball milling and spark plasma sintering in NaCl electrolyte. Specimens with grain sizes ranging from 0.3 µm to 3 µm, without crystallographic texture, were obtained and compared with a cast that is 110 µm in grain size and an annealed reference. The potentiodynamic experiments showed that the reduction in grain size leads to a degradation of the electrochemical passivation behavior. This detrimental effect can be overcome by appropriate passivation in a HNO3 concentrated solution before consolidation. The Mott–Schottky measurements showed that the semiconducting properties of the passive layer do not vary significantly on the grain size, especially the donor density, which is responsible for the chemical passivation breakdown by chloride anions. The total electrical resistance of the layer, measured by impedance spectroscopy is always lower than the one of a cast and annealed 316L, but it slightly increases with a reduction in grain size in the ultrafine grain range. This is followed by a slight increase in the thickness of the oxide layer. The effect of chloride ions is very pronounced in terms of passivation breakdown if the powder is not passivated prior to sintering. This leads to the nucleation and growth of subsurface main pits and the formation of secondary satellite pits, especially for the smallest grain sizes. Passivation of the 316L powder before sintering has been found to be an effective way to prevent this phenomenon.
Open AccessUltrafine Grain 316L Stainless Steel Manufactured by Ball Milling and Spark Plasma Sintering: Consequences on the Corrosion Resistance in Chloride Media
This paper reports experimental results concerning the corrosion of 316L austenitic stainless steels produced by ball milling and spark plasma sintering in NaCl electrolyte. Specimens with grain sizes ranging from 0.3 µm to 3 µm, without crystallographic texture, were obtained and compared with a cast that is 110 µm in grain size and an annealed reference. The potentiodynamic experiments showed that the reduction in grain size leads to a degradation of the electrochemical passivation behavior. This detrimental effect can be overcome by appropriate passivation in a HNO3 concentrated solution before consolidation. The Mott–Schottky measurements showed that the semiconducting properties of the passive layer do not vary significantly on the grain size, especially the donor density, which is responsible for the chemical passivation breakdown by chloride anions. The total electrical resistance of the layer, measured by impedance spectroscopy is always lower than the one of a cast and annealed 316L, but it slightly increases with a reduction in grain size in the ultrafine grain range. This is followed by a slight increase in the thickness of the oxide layer. The effect of chloride ions is very pronounced in terms of passivation breakdown if the powder is not passivated prior to sintering. This leads to the nucleation and growth of subsurface main pits and the formation of secondary satellite pits, especially for the smallest grain sizes. Passivation of the 316L powder before sintering has been found to be an effective way to prevent this phenomenon.