MBMahdieh Bozorgi

Mahdieh Bozorgi

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Mahdieh Bozorgi has a total of 4 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Anisotropic Metallic Grating With an Inhomogeneous Superstrate as a Broadband Reflective Polarization Converter: Design and Fabrication

    by Mahdieh Bozorgi, Mahmood Rafaei‐Booket

    A broadband reflective Linear‐To‐Circular Polarization (LTCP) converter is proposed in this work. Such a mechanically simple structure converts a linearly polarised incident plane wave into a circularly polarised reflected one with a minimum loss. In its design, an anisotropic metallic grating printed on the interior side of an inhomogeneous superstrate is utilised. Each re‐radiating element of this array is composed of a double concentric ring in which the inner ring is attached to two arc lines. The inhomogeneous superstrate, formed by a low‐cost FR4 dielectric slab with periodically drilled air holes to reduce structure loss, is mounted above a copper plane with an optimised spacing to minimise reflective wave loss. The dimensions of its unit cell are 10.6 × 10.6 × 1.8 mm 3 (0.25 λ × 0.25 λ × 0.043 λ ), where λ represents the free‐space wavelength of the lowest frequency in the operating bandwidth. To validate the numerical results, the designed structure with 12 × 7 cells is fabricated and tested. Measurements demonstrate the Axial Ratio (AR) < 3 dB, indicating near‐ideal circular polarization and the Polarization Conversion Rate (PCR) approaches unity within 7.2∼12.6 GHz. Such a structure can be used in various applications, such as weather monitoring multi‐beam/beam scanning antennas, wireless/radar tracking and navigation systems.

  • Open Access

    Record‐level, exceptionally broadband borophene‐based absorber with near‐perfect absorption: design and comparison with a graphene‐based counterpart

    by Amir Ali Marefati, Mahdieh Bozorgi

    We present a high performance ultra‐broadband optical absorber based on a metal–insulator–metal (MIM) configuration, enhanced by two‐dimensional (2D) materials: graphene and borophene. The base design includes a titanium resonator, an SiO 2 dielectric spacer, and a gold ground plane. Performance optimization is achieved through integration of 2D materials, anti‐reflection coatings (ARC), and tuning of structural parameters, Fermi energy, and surface carrier density. Numerical simulations using the finite difference time domain (FDTD) method show that incorporating borophene, due to its exceptionally high carrier density, leads to remarkable enhancement in both absorption amplitude and spectral bandwidth. When integrated with an optimized antireflection coating (ARC), the borophene‐based absorber achieves over 90 % absorption across 790–3,232 nm (bandwidth: 2,442 nm), corresponding to a 136 % enhancement over the base design. For absorption above 80 %, the bandwidth extends from 760 to 3,306 nm (2,546 nm), yielding a 125 % improvement. The associated fractional bandwidths are 121 % and 125 %, respectively. By comparison, the graphene‐based counterpart, with a properly tuned ARC and Fermi level, delivers over 90 % absorption within 923–2,108 nm (1,185 nm, 13 % improvement), while maintaining absorption above 80 % across 911–2,256 nm (1,345 nm, 12 % improvement), with corresponding fractional bandwidths of 78 % and 84 %. Comparative analysis underscores the critical importance of 2D material selection and placement, ARC and resonator optimization, and optical tuning in achieving optimal performance. These results indicate strong potential for practical applications in advanced optoelectronic and photonic devices, including infrared imaging, optical sensing, broadband photodetectors, solar energy harvesting, and stealth or thermal camouflage systems.


  • Open Access

    Self-Casing Low-Cost Reflectarray With a Single Porous Layer

    by Mahmood Rafaei-Booket, Mahdieh Bozorgi

    A self-casing Microstrip Reflectarray Antenna (MRA) is proposed with high-gain, broadband, mechanically simple properties. It needs no radome due to exploiting a low-cost porous superstrate. Such an inhomogeneous layer is made up of the robust FR4 dielectric in which air rods are periodically drilled. This porous layer is suspended above the metallic plane using spacer and the re-radiating elements are printed on its interior side for designing a broadband center-fed MRA. Its element is a new Butterfly-Like Patch (BLP) with two degrees of freedom (length and angle). By analyzing its sub-wavelength unit cell, the calculated total phase range is more than 700°, which can be a good choice for broadband MRA design. Using this phase response and an efficient phase synthesis technique, an optimized metallization arrangement is analytically obtained to design a good frequency behavior MRA. To validate the numerical results, a $270\times 270\times 3.9$ mm3 MRA with focal length 26.1 cm is manufactured and tested. Measured results show a peak gain 29.1dB with a 1-dB gain bandwidth of 42.6% ( $9.7\sim 14.9$ GHz) and maximum efficiency 58% at central frequency 12GHz. It is experimentally shown that the gain and bandwidth of this self-covering MRA is better than conventional one.


  • Dyadic Green's function of plasmonic nano-antenna gratings on natural/artificial anisotropic thin films

    by Mahmood Rafaei-Booket, Mahdieh Bozorgi

    We present an efficient technique to use the periodic method of moments (PMOM) in analyzing the plasmonic nano-antenna gratings (PNAGs) on natural/artificial anisotropic thin films. The artificial media are made up of two alternating isotropic regions in which the optic axis is chosen to be parallel to the period of grating due to its more complicated analysis. Dyadic Green's function (DGF) of these structures is obtained by utilizing the equivalent model of transmission line in Fourier domain and considering the plasmonic effects. Such a DGF is used in a series equation formulated for computing the effective electric currents induced on PNAG's surface. Solving such a series equation is carried out using Galerkin's version of PMOM with appropriate sub-domain functions. Using this technique, the scattering characteristics of different examples of double-screen PNAGs with homogeneous natural/inhomogeneous artificial anisotropic thin films are calculated. Assessment of this technique's efficiency is carried out by taking its cost–time and convergence rate vs truncation orders into account. It is shown that by using the developed technique, not only PNAGs with natural/artificial dielectrics can be analyzed within short time but also CPU and memory occupancies are reduced in comparison with commercial Electromagnetic (EM)-solvers.