Mosin Shaikh
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Mosin Shaikh has a total of 2 co-authors. Here are the top co-authors by number of shared publications:
Adik Yadao
Department of Mechanical Engineering, G H Raisoni College of Engineering and Management, Pune, India
1 shared publication- Adik Yadao
G H Raisoni College of Engineering and Management, Pune, India
1 shared publication
Latest Publications
- 24 April 2026
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering
Artificial neural network-based investigation of the effects of suspension dynamic properties on chassis vibrations
Nowadays the comfort level, stability and safety of vehicle are the important parameters considered in comparative analysis while selecting the vehicle. This paper explores a development of mathematical model for investigating the effect of suspension dynamic properties on the chassis vibration. Equations of motion derived for the model with seven degrees of freedom system and solved by Newmark Beta method programmed in MATLAB software to obtain the value of peak acceleration of automobile chassis. Sprung mass, equivalent spring stiffness, equivalent damping coefficient of shock absorber, amplitude of excitation, velocity of excitation and wavelength of excitation were considered as a suspension dynamic properties. The data obtained from the mathematical model gives strong foundation for building an accurate predictive model using an artificial neural network (ANN). Use of GridSearchCv with KerasRegressor optimizes the layer size, adding cross validation improves ANN model by avoiding over fitting of limited data. The ANN model cross validation results obtained with mean acceleration of 4.54792 m/s 2 and standard deviation of 1.47530 m/s 2 . For validation the experimental investigation of the chassis vibration performed on a car with monocoque chassis, Macpherson front suspension and twist beam rear suspension with coil spring considered and FFT analyzer used for the data collection. This model enables non linear mapping between suspension parameters and chassis response and having ability to handle different road inputs. With the validated theoretical model it is easy to generate large datasets for extreme conditions and it reduces time and cost of testing. This method forms a base to obtain more accurate prediction of the effect of suspension dynamic properties on the automobile chassis vibration to enhance the vehicle performance.
- 24 April 2026
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering
Artificial neural network-based investigation of the effects of suspension dynamic properties on chassis vibrations
Nowadays the comfort level, stability and safety of vehicle are the important parameters considered in comparative analysis while selecting the vehicle. This paper explores a development of mathematical model for investigating the effect of suspension dynamic properties on the chassis vibration. Equations of motion derived for the model with seven degrees of freedom system and solved by Newmark Beta method programmed in MATLAB software to obtain the value of peak acceleration of automobile chassis. Sprung mass, equivalent spring stiffness, equivalent damping coefficient of shock absorber, amplitude of excitation, velocity of excitation and wavelength of excitation were considered as a suspension dynamic properties. The data obtained from the mathematical model gives strong foundation for building an accurate predictive model using an artificial neural network (ANN). Use of GridSearchCv with KerasRegressor optimizes the layer size, adding cross validation improves ANN model by avoiding over fitting of limited data. The ANN model cross validation results obtained with mean acceleration of 4.54792 m/s 2 and standard deviation of 1.47530 m/s 2 . For validation the experimental investigation of the chassis vibration performed on a car with monocoque chassis, Macpherson front suspension and twist beam rear suspension with coil spring considered and FFT analyzer used for the data collection. This model enables non linear mapping between suspension parameters and chassis response and having ability to handle different road inputs. With the validated theoretical model it is easy to generate large datasets for extreme conditions and it reduces time and cost of testing. This method forms a base to obtain more accurate prediction of the effect of suspension dynamic properties on the automobile chassis vibration to enhance the vehicle performance.
- 15 January 2025
- Published by SAGE Publications in Noise & Vibration Worldwide
- Vol. 56 (1-2) , 38-51
Numerical and experimental investigation of vibration of a car chassis and its effect with road gradient on noise and response optimization with factorial design method
This paper delves in to a numerical and experimental investigation of vibration of a car chassis and its effect with road gradient on noise and response optimization. Peak acceleration, peak amplitude as vibration response parameters in vertical motion, internal and pass by noise as a noise response parameters. Vibration parameters obtained numerically by developing a mathematical model of car and equation of motion. Newmark Beta method programmed in MATLAB software used to solve the equation of motion. Experimental investigation of the vibration were carried on a car consist of monocoque chassis, three cylinder engine, Macpherson front suspension and twist beam rear suspension. FFT analyzer and digital sound level meter were used for the data collection. Pass by noise data of vehicle were collected at two locations with gradient 1.15° and 11.31° on state highway (MH SH-44) near Konchi Maharashtra state, India. Comparison between numerical and experimental investigated values of vibration parameters shows minimum error of 0.6035% and average error of 2.81% which validates the car model. Factorial design method was used to optimize the index of response parameters which shows reduction in peak acceleration, peak amplitude, internal noise and pass by noise level by 65.61%, 17.70%, 7.13% and 19.41% respectively. The methodology proposed in this study provides reference to improve the performance of car suspension and passenger comfort.
- 15 January 2025
- Published by SAGE Publications in Noise & Vibration Worldwide
- Vol. 56 (1-2) , 38-51
Numerical and experimental investigation of vibration of a car chassis and its effect with road gradient on noise and response optimization with factorial design method
This paper delves in to a numerical and experimental investigation of vibration of a car chassis and its effect with road gradient on noise and response optimization. Peak acceleration, peak amplitude as vibration response parameters in vertical motion, internal and pass by noise as a noise response parameters. Vibration parameters obtained numerically by developing a mathematical model of car and equation of motion. Newmark Beta method programmed in MATLAB software used to solve the equation of motion. Experimental investigation of the vibration were carried on a car consist of monocoque chassis, three cylinder engine, Macpherson front suspension and twist beam rear suspension. FFT analyzer and digital sound level meter were used for the data collection. Pass by noise data of vehicle were collected at two locations with gradient 1.15° and 11.31° on state highway (MH SH-44) near Konchi Maharashtra state, India. Comparison between numerical and experimental investigated values of vibration parameters shows minimum error of 0.6035% and average error of 2.81% which validates the car model. Factorial design method was used to optimize the index of response parameters which shows reduction in peak acceleration, peak amplitude, internal noise and pass by noise level by 65.61%, 17.70%, 7.13% and 19.41% respectively. The methodology proposed in this study provides reference to improve the performance of car suspension and passenger comfort.
- 25 July 2024
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering
Numerical and experimental investigation of vibration and response optimization of a car chassis with effect of changing driving speed
Vibration of automobile vehicles is the important issue in the entire vehicle design process as it affects the comfort level and the overall image of a vehicle, an experimental evaluation and prediction of vibration level of the vehicle in stationary and driving conditions are often necessary. This paper delves in to a numerical and experimental investigation of vibration and response optimization of a car chassis with peak acceleration and peak amplitude level of vibration as a response parameter in vertical motion. These response parameters were obtained numerically by developing a mathematical model of car and equation of motion. Newmark Beta method used to solve the equation of motion to get the values of response parameters in MATLAB software. For the experimental investigation of the response parameters a car with monocoque chassis, three cylinder engine, Macpherson front suspension and twist beam rear suspension with coil spring considered and FFT analyzer used for the data collection of the response parameters, FFT analyzer works on the fast Fourier transform algorithm. Comparative analysis between the numerical and experimental investigated values of response parameters shows the minimum error of 0.6035% and average error of 2.81% at various points on chassis; it shows the precision of the mathematical model and practical car model. To optimize the performance index of response parameters Fractional factorial design of experiment (DOE) method applied with six factors and two levels. The main effect analysis, analysis of contribution, analysis of variance and backward elimination method were applied in fractional factorial design. Regression equation for the response parameters were obtained with two level six factor fractional factorial design for the vibration level prediction. The comparative analysis of the response parameter levels before and after the optimization shows the reduction of 65.61% in peak acceleration level and reduction of 17.70% in the peak amplitude level of a car chassis with respect to change in the driving speed. The design and optimization method proposed in this study has a significant effect on the vibration reduction of the car chassis which provides a reference for the optimization of the vibration level to improve the performance of car suspension.
- 25 July 2024
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering
Numerical and experimental investigation of vibration and response optimization of a car chassis with effect of changing driving speed
Vibration of automobile vehicles is the important issue in the entire vehicle design process as it affects the comfort level and the overall image of a vehicle, an experimental evaluation and prediction of vibration level of the vehicle in stationary and driving conditions are often necessary. This paper delves in to a numerical and experimental investigation of vibration and response optimization of a car chassis with peak acceleration and peak amplitude level of vibration as a response parameter in vertical motion. These response parameters were obtained numerically by developing a mathematical model of car and equation of motion. Newmark Beta method used to solve the equation of motion to get the values of response parameters in MATLAB software. For the experimental investigation of the response parameters a car with monocoque chassis, three cylinder engine, Macpherson front suspension and twist beam rear suspension with coil spring considered and FFT analyzer used for the data collection of the response parameters, FFT analyzer works on the fast Fourier transform algorithm. Comparative analysis between the numerical and experimental investigated values of response parameters shows the minimum error of 0.6035% and average error of 2.81% at various points on chassis; it shows the precision of the mathematical model and practical car model. To optimize the performance index of response parameters Fractional factorial design of experiment (DOE) method applied with six factors and two levels. The main effect analysis, analysis of contribution, analysis of variance and backward elimination method were applied in fractional factorial design. Regression equation for the response parameters were obtained with two level six factor fractional factorial design for the vibration level prediction. The comparative analysis of the response parameter levels before and after the optimization shows the reduction of 65.61% in peak acceleration level and reduction of 17.70% in the peak amplitude level of a car chassis with respect to change in the driving speed. The design and optimization method proposed in this study has a significant effect on the vibration reduction of the car chassis which provides a reference for the optimization of the vibration level to improve the performance of car suspension.