Mingxin Geng
Mingxin Geng has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
Bai Xiao-Chun
1 shared publication- Bin Yang
Key Laboratory of Biomass Chemical Engineering of Ministry of Education, College of Chemical and Biological Engineering Zhejiang University Hangzhou China
1 shared publication - Chen Shen
State Grid Shaanxi Electric Power Research Institute, Xi'an 710100, China
1 shared publication - Chen Shen
Power Research Institute of State Grid Shaanxi Electric Power Company Limited 1 , Xi ’an 710100, China
1 shared publication - Dianlong Yu
College of Intelligence Science and Technology, National University of Defense Technology, Changsha, China
1 shared publication - Jian Wu
Xi’an Jiaotong University
1 shared publication
Latest Publications
- Open Access
- 1 August 2024
- Published by AIP Publishing in AIP Advances
- Vol. 14 (8)
Theoretical and experimental study on time-domain monopole time reversal method with excluding autocorrelation
Monopole time reversal is an advanced noise source localization technique, but its sidelobe level in localizing sound sources is greatly affected by noise, leading to a decrease in the accuracy of sound source localization under a low signal-to-noise ratio. To address this issue, this paper proposes a time-domain monopole time reversal technique that excludes autocorrelation to reduce the impact of noise on sound source localization results. Numerical simulation and experimental results show that, compared to conventional monopole time reversal techniques, the proposed method can effectively reduce the sidelobes in sound source localization results and achieve accurate sound source localization under −20 dB low signal-to-noise ratio conditions.
- 1 August 2024
- Published by AIP Publishing in AIP Advances
- Vol. 14 (8)
Open AccessTheoretical and experimental study on time-domain monopole time reversal method with excluding autocorrelation
Monopole time reversal is an advanced noise source localization technique, but its sidelobe level in localizing sound sources is greatly affected by noise, leading to a decrease in the accuracy of sound source localization under a low signal-to-noise ratio. To address this issue, this paper proposes a time-domain monopole time reversal technique that excludes autocorrelation to reduce the impact of noise on sound source localization results. Numerical simulation and experimental results show that, compared to conventional monopole time reversal techniques, the proposed method can effectively reduce the sidelobes in sound source localization results and achieve accurate sound source localization under −20 dB low signal-to-noise ratio conditions.
- 1 December 2021
- Published by Elsevier in Applied Acoustics
- Vol. 183, 108290
Urban 110 kV indoor substation noise analysis and control schemes: A real case study
- 1 December 2021
- Published by Elsevier in Applied Acoustics
- Vol. 183, 108290
Urban 110 kV indoor substation noise analysis and control schemes: A real case study
- Open Access
- 1 January 2016
- Published by Acta Physica Sinica, Chinese Physical Society and Institute of Physics, Chinese Academy of Sciences in Acta Physica Sinica
- Vol. 65 (6) , 064602
Low frequency band gaps and vibration reduction properties of a multi-frequency locally resonant phononic plate
A multi-frequency locally resonant (LR) phononic plate is proposed in this paper. The phononic plate consists of periodic arrays of multiple double-cantilevered thin beams attached to a thin homogeneous plate. This proposed phononic plate is simplified and modeled using a plane wave expansion method to enable the calculation of flexural wave band structures. The band gap behavior of the phononic plate is analyzed comprehensively. In addition, an experimental specimen is fabricated using a square aluminum plate with a thickness of 0.9 mm and an area of 840 mm840 mm, and attached to the specimens as periodic arrays of two types of double-cantilevered thin beams made of the same material as the host plate. And the specimen is measured by using a scanning laser Doppler vibrometer to verify the theoretical predictions of band gaps. Investigations of this paper yield the following findings and conclusions: (1) Due to the interaction of low-frequency vibrational modes of attached multiple double-cantilevered beams and flexural vibration of the host plate, the proposed multi-frequency LR phononic plate can exhibit multiple low-frequency flexural wave band gaps (stop bands). It is also found that the band gaps of a multi-frequency LR phononic plate, especially those appearing in a lower frequency range, are generally narrower than that of a single-frequency LR phononic plate with the same type of double-cantilevered beams. (2) The frequency location of band gaps moves to higher frequency range when the thickness of the double-cantilevered beams is increased, or when the length of the double-cantilevered beams is decreased. It is also shown that a very small variation of the thickness (e. g., 0.1 mm) may lead to significant changes of frequency position of the band gaps. (3) When the width of the double-cantilevered beams is enlarged or the number of the double-cantilevered beams is increased, the lower band gap edge will move to a lower frequency range, while the upper band gap edge will move to a higher frequency range. This implies that the bandwidth of the band gaps is broadened. However, at the same time, it is shown that the central frequencies of the band gaps remain almost unchanged. (4) Experimental measurements of the fabricated specimen evidence the existence of two low frequency band gaps, and confirm that the flexural plate vibrations are significantly reduced in the predicted band gaps.
- 1 January 2016
- Published by Acta Physica Sinica, Chinese Physical Society and Institute of Physics, Chinese Academy of Sciences in Acta Physica Sinica
- Vol. 65 (6) , 064602
Open AccessLow frequency band gaps and vibration reduction properties of a multi-frequency locally resonant phononic plate
A multi-frequency locally resonant (LR) phononic plate is proposed in this paper. The phononic plate consists of periodic arrays of multiple double-cantilevered thin beams attached to a thin homogeneous plate. This proposed phononic plate is simplified and modeled using a plane wave expansion method to enable the calculation of flexural wave band structures. The band gap behavior of the phononic plate is analyzed comprehensively. In addition, an experimental specimen is fabricated using a square aluminum plate with a thickness of 0.9 mm and an area of 840 mm840 mm, and attached to the specimens as periodic arrays of two types of double-cantilevered thin beams made of the same material as the host plate. And the specimen is measured by using a scanning laser Doppler vibrometer to verify the theoretical predictions of band gaps. Investigations of this paper yield the following findings and conclusions: (1) Due to the interaction of low-frequency vibrational modes of attached multiple double-cantilevered beams and flexural vibration of the host plate, the proposed multi-frequency LR phononic plate can exhibit multiple low-frequency flexural wave band gaps (stop bands). It is also found that the band gaps of a multi-frequency LR phononic plate, especially those appearing in a lower frequency range, are generally narrower than that of a single-frequency LR phononic plate with the same type of double-cantilevered beams. (2) The frequency location of band gaps moves to higher frequency range when the thickness of the double-cantilevered beams is increased, or when the length of the double-cantilevered beams is decreased. It is also shown that a very small variation of the thickness (e. g., 0.1 mm) may lead to significant changes of frequency position of the band gaps. (3) When the width of the double-cantilevered beams is enlarged or the number of the double-cantilevered beams is increased, the lower band gap edge will move to a lower frequency range, while the upper band gap edge will move to a higher frequency range. This implies that the bandwidth of the band gaps is broadened. However, at the same time, it is shown that the central frequencies of the band gaps remain almost unchanged. (4) Experimental measurements of the fabricated specimen evidence the existence of two low frequency band gaps, and confirm that the flexural plate vibrations are significantly reduced in the predicted band gaps.