Andrey Volokitin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Andrey Volokitin has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Irina E. Volokitina
Karaganda industrial university, Temirtau, Kazakhstan
3 shared publications - Bolat Makhmutov
Department for Research and International Cooperation, Karaganda Industrial University, Temirtau 101400, Kazakhstan
2 shared publications A. I. Denissova
Karaganda Ind Univ, 30 Republ Ave, Temirtau KZ-101400, Kazakhstan
1 shared publication- Anastassiya Denissova
Karaganda industrial university, Temirtau, Kazakhstan
1 shared publication D. N. Lavrinyuk
Karaganda Ind Univ, 30 Republ Ave, Temirtau 101400, Kazakhstan
1 shared publicationE. A. Panin
Karaganda Ind Univ, 30 Republ Ave, Temirtau 101400, Kazakhstan
1 shared publication
Latest Publications
- Open Access
Obtaining Symmetrical Gradient Structure in Copper Wire by Combined Processing
Traditionally, structural wire is characterized by a homogeneous microstructure, where the average grain size in different parts of the wire is uniform. According to the classical Hall–Petch relationship, a homogeneous polycrystalline metal can be strengthened by decreasing the average grain size since an increase in the volume fraction of grain boundaries will further impede the motion of dislocations. However, a decrease in the grain size inevitably leads to a decrease in the ductility and deformability of the material due to limited dislocation mobility. Putting a gradient microstructure into the wire has promising potential for overcoming the compromise between strength and ductility. This is proposed a new combined technology in this paper in order to obtain a gradient microstructure. This technology consists of deforming the wire in a rotating equal-channel step die and subsequent traditional drawing. Deformation of copper wire with a diameter of 6.5 mm to a diameter of 5.0 mm was carried out in three passes at room temperature. As a result of such processing, a gradient microstructure with a surface nanostructured layer (grain size ~400 nm) with a gradual increase in grain size towards the center of the wire was obtained. As a result, the microhardness in the surface zone was 1150 MPa, 770 Mpa in the neutral zone, and 685 MPa in the central zone of the wire. Such a symmetrical spread of microhardness, observed over the entire cross-section of the rod, is a direct confirmation of the presence of a gradient microstructure in deformed materials. The strength characteristics of the wire were doubled: the tensile strength increased from 335 MPa to 675 MPa, and the yield strength from 230 MPa to 445 MPa. At the same time, the relative elongation decreased from 20% to 16%, and the relative contraction from 28% to 23%. Despite the fact that the ductility of copper is decreased after cyclic deformation, its values remain at a fairly high level. The validity of all results is confirmed by numerous experiments using a complex of traditional and modern research methods, which include optical, scanning, and transmission microscopy; determination of mechanical properties under tension; and measurement of hardness and electrical resistance. These methods allow reliable interpretation of the fine microstructure of the wire and provide information on its strength, plastic, and electrical properties.
Open AccessObtaining Symmetrical Gradient Structure in Copper Wire by Combined Processing
Traditionally, structural wire is characterized by a homogeneous microstructure, where the average grain size in different parts of the wire is uniform. According to the classical Hall–Petch relationship, a homogeneous polycrystalline metal can be strengthened by decreasing the average grain size since an increase in the volume fraction of grain boundaries will further impede the motion of dislocations. However, a decrease in the grain size inevitably leads to a decrease in the ductility and deformability of the material due to limited dislocation mobility. Putting a gradient microstructure into the wire has promising potential for overcoming the compromise between strength and ductility. This is proposed a new combined technology in this paper in order to obtain a gradient microstructure. This technology consists of deforming the wire in a rotating equal-channel step die and subsequent traditional drawing. Deformation of copper wire with a diameter of 6.5 mm to a diameter of 5.0 mm was carried out in three passes at room temperature. As a result of such processing, a gradient microstructure with a surface nanostructured layer (grain size ~400 nm) with a gradual increase in grain size towards the center of the wire was obtained. As a result, the microhardness in the surface zone was 1150 MPa, 770 Mpa in the neutral zone, and 685 MPa in the central zone of the wire. Such a symmetrical spread of microhardness, observed over the entire cross-section of the rod, is a direct confirmation of the presence of a gradient microstructure in deformed materials. The strength characteristics of the wire were doubled: the tensile strength increased from 335 MPa to 675 MPa, and the yield strength from 230 MPa to 445 MPa. At the same time, the relative elongation decreased from 20% to 16%, and the relative contraction from 28% to 23%. Despite the fact that the ductility of copper is decreased after cyclic deformation, its values remain at a fairly high level. The validity of all results is confirmed by numerous experiments using a complex of traditional and modern research methods, which include optical, scanning, and transmission microscopy; determination of mechanical properties under tension; and measurement of hardness and electrical resistance. These methods allow reliable interpretation of the fine microstructure of the wire and provide information on its strength, plastic, and electrical properties.
- Open Access
Symmetrical Martensite Distribution in Wire Using Cryogenic Cooling
This article presents the results of research on a new combined process involving multi-cycle wire-drawing and subsequent cryogenic cooling after each deformation stage. For theoretical research, modeling in the Deform software was performed. The analysis of temperature fields and the martensitic component in all models showed that for both considered thicknesses, the most effective option is a low deformation velocity and the conduct of a process without heating. The least effective option is to use an increased thickness of the workpiece at an increased deformation velocity and the conduct of a process without of heating to ambient temperature, which acts as a local cooling of the axial zone of the workpiece with an increase in the workpiece thickness. An analysis of laboratory studies on this combined process revealed that in the absence of intermediate heating of a wire between deformation cycles, 100% martensite is formed in the structure. However, if intermediate heating to 20 °C between deformation cycles is carried out, a gradient distribution of martensite can be obtained. And, since the wire has a circular cross-section, in all cases, martensite is distributed symmetrically about the center of the workpiece.
Open AccessSymmetrical Martensite Distribution in Wire Using Cryogenic Cooling
This article presents the results of research on a new combined process involving multi-cycle wire-drawing and subsequent cryogenic cooling after each deformation stage. For theoretical research, modeling in the Deform software was performed. The analysis of temperature fields and the martensitic component in all models showed that for both considered thicknesses, the most effective option is a low deformation velocity and the conduct of a process without heating. The least effective option is to use an increased thickness of the workpiece at an increased deformation velocity and the conduct of a process without of heating to ambient temperature, which acts as a local cooling of the axial zone of the workpiece with an increase in the workpiece thickness. An analysis of laboratory studies on this combined process revealed that in the absence of intermediate heating of a wire between deformation cycles, 100% martensite is formed in the structure. However, if intermediate heating to 20 °C between deformation cycles is carried out, a gradient distribution of martensite can be obtained. And, since the wire has a circular cross-section, in all cases, martensite is distributed symmetrically about the center of the workpiece.
- Open Access
Formation of Symmetric Gradient Microstructure in Carbon Steel Bars
In recent years, severe plastic deformation has attracted the most attention as a way to improve the mechanical properties of steel bars. Obtaining ultrafine grains and nanostructures in such bars leads to a strong increase in strength properties but strongly reduces their plastic properties. This study shows that the formation of a gradient microstructure allows simultaneous improvement in the strength and plastic properties of carbon steel bars, taking into account the symmetry of the microstructure distribution from the center of machining. A new combined technology is proposed to obtain such a microstructure. This technology consists of drawing bars from medium carbon steel on a radial-displacement rolling mill and carrying out subsequent drawing. Steel bars with a diameter of 30 mm were strained in three passes to a diameter of 16 mm at room temperature. The results show that the average value of microhardness in the center, neutral, and surface areas for the three straining cycles were 1890 MPa, 2335 MPa, and 2920 MPa, respectively. This symmetrical distribution of microhardness confirms the gradient microstructure. Strength characteristics also increased almost twofold: the yield strength increased from 330 to 735 MPa, and the ultimate strength increased from 600 MPa to 1025 MPa. Relative elongation decreased from 18 to 14 MPa, and relative reduction decreased from 40 to 31%, but remained at a fairly good level for AISI 1045 steel. The validity of all results was confirmed through numerous experiments using a set of traditional and modern research methods, which included optical, scanning, and transmission microscopy. EBSD analysis allowed precise positioning of the field of vision for studying microstructural changes across the entire bar cross-section. All of these methods used together, including tensile testing of the mechanical properties and the fractographic method, allow us to assess changes in microhardness and the reproduction of results.
Open AccessFormation of Symmetric Gradient Microstructure in Carbon Steel Bars
In recent years, severe plastic deformation has attracted the most attention as a way to improve the mechanical properties of steel bars. Obtaining ultrafine grains and nanostructures in such bars leads to a strong increase in strength properties but strongly reduces their plastic properties. This study shows that the formation of a gradient microstructure allows simultaneous improvement in the strength and plastic properties of carbon steel bars, taking into account the symmetry of the microstructure distribution from the center of machining. A new combined technology is proposed to obtain such a microstructure. This technology consists of drawing bars from medium carbon steel on a radial-displacement rolling mill and carrying out subsequent drawing. Steel bars with a diameter of 30 mm were strained in three passes to a diameter of 16 mm at room temperature. The results show that the average value of microhardness in the center, neutral, and surface areas for the three straining cycles were 1890 MPa, 2335 MPa, and 2920 MPa, respectively. This symmetrical distribution of microhardness confirms the gradient microstructure. Strength characteristics also increased almost twofold: the yield strength increased from 330 to 735 MPa, and the ultimate strength increased from 600 MPa to 1025 MPa. Relative elongation decreased from 18 to 14 MPa, and relative reduction decreased from 40 to 31%, but remained at a fairly good level for AISI 1045 steel. The validity of all results was confirmed through numerous experiments using a set of traditional and modern research methods, which included optical, scanning, and transmission microscopy. EBSD analysis allowed precise positioning of the field of vision for studying microstructural changes across the entire bar cross-section. All of these methods used together, including tensile testing of the mechanical properties and the fractographic method, allow us to assess changes in microhardness and the reproduction of results.
- Open Access
- 25 March 2024
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Metallofizika i Noveishie Tekhnologii
- Vol. 46 (2) , 121-128
Evolution of Copper Microstructure Subjected to Combined Twisting and Drawing Technology
- 25 March 2024
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Metallofizika i Noveishie Tekhnologii
- Vol. 46 (2) , 121-128
Open AccessEvolution of Copper Microstructure Subjected to Combined Twisting and Drawing Technology
- Open Access
- 5 March 2024
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Metallofizika i Noveishie Tekhnologii
- Vol. 45 (11) , 1311-1335
Mechanisms of Structure Formation under Severe Plastic Deformation: A Review
- 5 March 2024
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Metallofizika i Noveishie Tekhnologii
- Vol. 45 (11) , 1311-1335
Open AccessMechanisms of Structure Formation under Severe Plastic Deformation: A Review