MSManny De Silva

Manny De Silva

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Manny De Silva has a total of 18 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Type II fiber Bragg gratings with a 181 nm period fabricated using tightly focused deep-ultraviolet femtosecond laser pulses

    by Cyril Hnatovsky, Rune Lausten, Abdullah Rahnama, Manjula De Silva, Stephen J. Mihailov

    1100°C-resistant Bragg gratings with a 181 nm period were fabricated in non-photosensitized silica-based optical fibers using tightly focused deep-ultraviolet (267 nm) femtosecond laser pulses and the phase-mask technique. Changes in the transmission spectra of the fiber Bragg gratings were monitored as the surrounding temperature was increased in steps from 20°C to 1100°C and then held at 1100°C for, depending on the fiber, 60 or 100 minutes. The results showed that, both before and after the annealing, the gratings strongly and directionally outcoupled light and did not undergo a regeneration cycle during the annealing. Therefore, the gratings almost certainly consist of truly periodic mesoscopic structural disruptions in the host material.

  • 1000 °C-Stable Volume Bragg Gratings Written Line-by-Line With Ultrafast Laser Beam Filamentation

    by Abdullah Rahnama, Cyril Hnatovsky, Manny De Silva, Robert B. Walker, Stephen J. Mihailov

    Volume Bragg gratings with a 1 μm grating pitch and high diffraction efficiency of up to 94% are fabricated using line-by-line femtosecond laser writing of filaments of modified material in fused silica plates. Uniform filaments‒up to 150 μm in length‒are produced by tightly focusing the femtosecond pulses deep inside the plates and exploiting spherical aberration, induced by the planar air-sample interface, to stretch the focal volume of the focused pulses. The resultant VBGs exhibit high diffraction efficiency, high angular selectivity, and low polarization dependence. The VBGs also preserve their optical characteristics after isothermal annealing for 2 hours at 1000 °C.

  • BNNT Coated FBGs in Tapered Optical Fibers for Temperature and Hydrophilic Gas Sensing

    by Ping Lu, Jingwen Guan, Huimin Ding, Cyril Hnatovsky, Kasthuri De Silva, Christopher Kingston, Stephen J. Mihailov

    Fiber Bragg gratings (FBGs) were fabricated in tapered fibers using both the plane-by-plane and phase mask approaches with a femtosecond infrared laser. A thin layer of boron nitride nanotubes (BNNTs) was deposited onto the FBGs through a dip-coating process from a BNNT water solution. The reflection spectra of the FBGs were then recorded when they were placed in ammonia (NH3), hydrogen chloride (HCl) and bromine (Br2) gases. It was demonstrated experimentally that, due to the BNNT coating, the return losses of the FBGs increased when they were surrounded with these hydrophilic gas vapors. However, when the FBGs were in other atmospheres such as air, methanol and acetone vapors, no change in the FBG reflection spectra was observed. The results of this work indicate that BNNT coatings on FBGs can play an important role for hydrophilic gas detection with large measurement range and reusability due to their quick release of adsorbed gases. Moreover, the BNNT coating induced losses with different ammonia gas concentrations were quantitatively measured. It was observed that the Bragg wavelengths of the FBGs remained the same when the FBGs were tested in hydrophilic gases suggesting the proposed device can be used for temperature or strain sensing at the same time. The response of the Bragg wavelength of BNNT coated FBGs to temperature was also studied and it was found that the thin BNNT coating did not affect the FBG's temperature sensitivity. Due to the properties of BNNTs and optical fibers, the proposed fiber sensor can be used in harsh environments.


  • Open Access

    Characterization of the Second Harmonic Generation of Boron Nitride Nanotube Macroscopic Assemblies

    by Ping Lu, Jingwen Guan, Cyril Hnatovsky, Huimin Ding, Kasthuri De Silva, Liliana Gaburici, Christopher Kingston, Stephen J. Mihailov

    Boron nitride nanotubes (BNNTs) are predicted to be promising one-dimensional nonlinear optical materials, but to date, only one experimental observation has been made using individual nanotubes. In this work, second harmonic generation (SHG) was achieved from free-standing bulk BNNT sheets and BNNT coatings on silica substrates. Focusing femtosecond infrared (fs-IR) laser pulses with a wavelength of 800 nm onto the BNNT assemblies resulted in strong SHG at a wavelength of 400 nm. It was observed that due to the thickness variation of the BNNT assemblies and orientational alignment of BNNTs in the assemblies, the intensity of the second-harmonic (SH) radiation changed dramatically when different locations on the samples were investigated. Among all the BNNT assemblies tested, the localized SH response and its dependence on the polarization of the excitation fs-IR pulses were the strongest in BNNT coatings produced by a dip-coating process. By measuring the SH response, the uniformity, reproducibility, and efficiency of BNNT deposition processes could be assessed. For applications requiring a high SH response from BNNT assemblies, the process of dip coating is preferred.


  • Open Access

    Long-Term Wavelength Stability of Large Type II FBG Arrays in Different Silica-Based Fibers at High Temperature

    by Robert B. Walker, Stephen J. Mihailov, Cyril Hnatovsky, Manny De Silva, Ping Lu, Huimin Ding, Abdullah Rahnama

    Fiber Bragg gratings (FBGs) are useful components in fiber optic sensing systems, which can be highly multiplexed and distributed. In recent years, fabrication using ultrafast lasers has made these devices much more versatile and robust, but questions concerning their high-temperature performance remain. The wavelength resonance of an FBG is naturally sensitive to various parameters of its environment; in particular, changes in the temperature or strain of a fiber tend to induce observable shifts in the Bragg wavelength. Thus, FBGs can offer reliable sensing solutions, provided they are isolated from other influences and their wavelength responses remain well characterized. Nonetheless, it is important to be aware that the isothermal wavelength drift of unstrained FBGs has been previously observed. When this occurs, it can lead to measurement errors and a requirement for sensor recalibration. This study presents a comparison of long-term isothermal wavelength drifts observed at 600 °C, 800 °C, 900 °C and 1000 °C for large numbers of Type II FBGs in different kinds of single-mode fibers. The results provide guidance for the design of high-temperature sensing systems, both in terms of fiber selection and for estimating the maximum time before recalibration becomes necessary to maintain a specified accuracy.


  • Refractive Index Determination and Air-Void Characterization of BNNT Assembly Using Optical Fiber Bragg Grating Sensors

    by Ping Lu, Jingwen Guan, Huimin Ding, Kasthuri De Silva, Christopher Kingston, Stephen J. Mihailov

    The optical and structural properties of boron nitride nanotube (BNNT) assembly were characterized using optical fiber Bragg grating (FBG) sensors. FBGs were fabricated in tapered fibers with a diameter of less than 30 μm. After tapered fibers were etched in hydrofluoric acid solution for a few minutes, BNNTs were then deposited on the fibers through a dip-coating process. The Bragg wavelengths of the FBGs were measured before and after BNNT coating such that the effective refractive index (RI) of the guided fundamental HE11 mode in the fiber was obtained. By numerical modeling of the dependence of HE11 mode effective RI on the RI of the surrounding material, both the RI and the air void content of BNNT coating were obtained. To verify the accuracy of the modeling results, a FBG sensor fabricated in a tapered fiber was immerged in various RI standard solutions and the corresponding Bragg wavelengths were measured and compared to numerical simulations. It was shown that the experimental data agreed well with simulation results.


  • Open Access

    Through-The-Coating Fabrication of Fiber Bragg Grating Relative Humidity Sensors Using Femtosecond Pulse Duration Infrared Lasers and a Phase Mask

    by Stephen J. Mihailov, Huimin Ding, Cyril Hnatovsky, Robert B. Walker, Ping Lu, Manny De Silva

    Fiber Bragg grating (FBG) relative humidity (RH) sensors are fabricated in commercially available polyimide (PI)-coated optical fibers with diameters of 50 and 125 μm. Infrared (800 nm) femtosecond pulse duration laser pulses and a phase mask are used to inscribe Type-I and Type-II FBGs directly through the protective polyimide coatings of both 50 and 125 μm diameter fibers without typical fiber processing such as hydrogen loading, cryogenic storage, stripping, recoating or annealing. The devices are then evaluated for their performance as humidity sensors. At telecom wavelengths, the 50 μm diameter fiber devices with a 10 μm thick PI coating had a wavelength shift of the Bragg resonance at a constant temperature of 2.7 pm/%RH, whereas the 125 μm diameter fiber devices with a 17 μm thick PI coating had a wavelength shift of 1.8 pm/%RH. The humidity sensors in the 50 µm diameter fiber demonstrated a more rapid response time to small changes in humidity and a weaker hysteresis when compared to the 125 µm diameter fiber devices. No modification to the PI coatings was observed during fabrication. No difference in RH sensitivity was observed for Type-I devices when compared with Type-II devices with the same fiber. The applicability of this approach for fabricating distributed RH sensing arrays with hundreds of sensing elements on a single fiber is discussed.


  • Open Access

    Ultrafast Laser Processing of Optical Fibers for Sensing Applications

    by Stephen J. Mihailov, Cyril Hnatovsky, Nurmemet Abdukerim, Robert B. Walker, Ping Lu, Yanping Xu, Xiaoyi Bao, Huimin Ding, Manny De Silva, David Coulas, et al.

    A review of recent progress in the use of infrared femtosecond lasers to fabricate optical fiber sensors that incorporate fiber Bragg gratings (FBG) and random fiber gratings (RFG) is presented. The important advancements in femtosecond laser writing based on the phase mask technique now allow through-the-coating (TTC) fabrication of Bragg gratings in ultra-thin fiber filaments, tilted fiber Bragg gratings, and 1000 °C-resistant fiber Bragg gratings with very strong cladding modes. As an example, through-the-coating femtosecond laser writing is used to manufacture distributed fiber Bragg grating sensor arrays for oil pipeline leak detection. The plane-by-plane femtosecond laser writing technique used for the inscription of random fiber gratings is also reviewed and novel applications of the resultant devices in distributed temperature sensing, fiber lasers and fiber laser sensors are discussed.