Benoit Racine
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Benoit Racine has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Alexis P. A. Fischer
Laboratoire de Physique des Lasers, UMR CNRS 7538, Universit Sorbonne Paris Nord, Villetaneuse, France
1 shared publication C. Laugier
Université Grenoble Alpes, CEA, Leti 1 , Grenoble 38000, France
1 shared publicationC. Sésé
Université Grenoble Alpes, CEA, Leti 1 , Grenoble 38000, France
1 shared publication- D. Oussalah
Université Grenoble Alpes, CEA, Leti 1 , Grenoble 38000, France
1 shared publication - Jacques Baylet
Université Grenoble Alpes, CEA, Leti 1 , Grenoble 38000, France
1 shared publication - Jérôme Vaillant
Univ. Grenoble Alpes
1 shared publication
Latest Publications
- 3 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 35 (24) , 1399-1402
2.85-Gb/s Organic Light Communication With a 459-MHz Micro-OLED
We present a broadband free space light communication system using high-speed organic light emitting diodes (OLEDs) as transmitters. Firstly, we report the design and bandwidth measurements of micro-OLEDs with active area of 40x40μm². For this OLED, a cut-off frequency up to 459 MHz is observed. Secondly, by applying Direct Current Optical Orthogonal Frequency Division Multiplexing (DCO-OFDM) with adaptive bit and energy loading techniques, a data rate of 2.85 Gb/s is achieved. The increase of bandwidth and throughput reported in the current work are attributed to the improvements at the material, device and transmission levels. At the material level, a low work function Calcium cathode and ALD encapsulation of OLED is considered. At the device level, the active area is reduced in size and the OLEDs thickness is optimized. At the transmission level, parameters such as bias voltage, modulation amplitude and clipping have been fine-tuned to obtain high data rate.
- 3 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 35 (24) , 1399-1402
2.85-Gb/s Organic Light Communication With a 459-MHz Micro-OLED
We present a broadband free space light communication system using high-speed organic light emitting diodes (OLEDs) as transmitters. Firstly, we report the design and bandwidth measurements of micro-OLEDs with active area of 40x40μm². For this OLED, a cut-off frequency up to 459 MHz is observed. Secondly, by applying Direct Current Optical Orthogonal Frequency Division Multiplexing (DCO-OFDM) with adaptive bit and energy loading techniques, a data rate of 2.85 Gb/s is achieved. The increase of bandwidth and throughput reported in the current work are attributed to the improvements at the material, device and transmission levels. At the material level, a low work function Calcium cathode and ALD encapsulation of OLED is considered. At the device level, the active area is reduced in size and the OLEDs thickness is optimized. At the transmission level, parameters such as bias voltage, modulation amplitude and clipping have been fine-tuned to obtain high data rate.
- Open Access
- 28 September 2021
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 130 (12) , 125502
On the minimum thickness of doped electron/hole transport layers in organic semiconductor devices
Doped hole (respectively electron) transport layers [HTLs (respectively ETLs)] are commonly used in evaporated organic devices to achieve high work function hole contact (respectively low work function electron contact) in organic LEDs to inject large current, in solar cells to increase the open circuit voltage, and in photodetectors to minimize the dark current. However, optimization of the HTL thickness results from a delicate trade-off. Indeed, on the one hand, to minimize the impact of HTLs on light propagation and series resistance effects, it is commonly admitted that HTLs must be kept as thin as possible. In this work, a model, validated by drift and diffusion simulations, has shown that, depending of the doping level, a minimum thickness between 10 and 20 nm was needed to prevent the transport layer work function from degradation due to field effects. Experiments have been performed on template p-only devices featuring a single HTL of various thicknesses and doping, confirming the validity of the model. Finally, simulations have been performed on a p-i-n device featuring both HTL and ETL. These results constitute precious indications for the design of efficient evaporated organic LEDs, solar cells, or photodetectors.
- 28 September 2021
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 130 (12) , 125502
Open AccessOn the minimum thickness of doped electron/hole transport layers in organic semiconductor devices
Doped hole (respectively electron) transport layers [HTLs (respectively ETLs)] are commonly used in evaporated organic devices to achieve high work function hole contact (respectively low work function electron contact) in organic LEDs to inject large current, in solar cells to increase the open circuit voltage, and in photodetectors to minimize the dark current. However, optimization of the HTL thickness results from a delicate trade-off. Indeed, on the one hand, to minimize the impact of HTLs on light propagation and series resistance effects, it is commonly admitted that HTLs must be kept as thin as possible. In this work, a model, validated by drift and diffusion simulations, has shown that, depending of the doping level, a minimum thickness between 10 and 20 nm was needed to prevent the transport layer work function from degradation due to field effects. Experiments have been performed on template p-only devices featuring a single HTL of various thicknesses and doping, confirming the validity of the model. Finally, simulations have been performed on a p-i-n device featuring both HTL and ETL. These results constitute precious indications for the design of efficient evaporated organic LEDs, solar cells, or photodetectors.