Hiroki Shimomura
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Hiroki Shimomura has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Koji Yamamoto
Faculty of Information and Human Sciences, Kyoto Institute of Technology, Kyoto, Japan
2 shared publications - Akihito Taya
The University of Tokyo, Tokyo, Japan
1 shared publication - Hiromitsu Awano
Graduate School of Informatics, Kyoto University, Kyoto, Japan
1 shared publication - Sota Kondo
Graduate School of Informatics, Kyoto University, Kyoto, Japan
1 shared publication - Takamochi Kanda
Graduate School of Informatics, Kyoto University, Yoshida-Honmachi, Kyoto, Japan
1 shared publication - Takashi Sato
Kyoto University
1 shared publication
Latest Publications
- Open Access
- 19 August 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 13, 146008-146019
Beamforming Feedback-Based Respiration and Heart Rate Estimation Toward Firmware-Agnostic WiFi Sensing
WiFi-based vital sign monitoring has attracted growing attention for its potential applications in contactless healthcare. However, most existing techniques rely on channel state information (CSI), which typically requires custom firmware and specific chipsets. To address this issue, this study explores firmware-agnostic respiration and heart rate estimation using beamforming feedback (BFF), compressed representation of CSI. This eliminates the need for custom firmware or chipset support, enabling broader applicability using off-the-shelf devices. However, it is not trivial to apply CSI-based estimation techniques to BFF-based estimation because the information content and data structure of BFF differ from those of CSI. The proposed BFF-based estimation algorithm addresses this issue by adapting the CSI-based estimation techniques to work with BFF. The algorithm consists of four key components: subcarrier selection, data calibration, signal extraction, and respiration and heart rate estimation. The performance of the BFF-based estimation algorithm is experimentally validated in several indoor environments using commodity IEEE 802.11ac devices. Results show that respiration rate and heart rate can be estimated with average errors below 1 breaths/min and 10 beats/min, respectively. Furthermore, accuracy comparisons between BFF-based and CSI-based estimations are provided to investigate the impact of lossy compression from CSI to BFF, specifically singular value decomposition (SVD) calculation and quantization. Comparisons reveal that the accuracy degradation of the BFF-based estimation compared to CSI-based estimation is primarily caused by the quantization rather than the SVD calculation.
- 19 August 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 13, 146008-146019
Open AccessBeamforming Feedback-Based Respiration and Heart Rate Estimation Toward Firmware-Agnostic WiFi Sensing
WiFi-based vital sign monitoring has attracted growing attention for its potential applications in contactless healthcare. However, most existing techniques rely on channel state information (CSI), which typically requires custom firmware and specific chipsets. To address this issue, this study explores firmware-agnostic respiration and heart rate estimation using beamforming feedback (BFF), compressed representation of CSI. This eliminates the need for custom firmware or chipset support, enabling broader applicability using off-the-shelf devices. However, it is not trivial to apply CSI-based estimation techniques to BFF-based estimation because the information content and data structure of BFF differ from those of CSI. The proposed BFF-based estimation algorithm addresses this issue by adapting the CSI-based estimation techniques to work with BFF. The algorithm consists of four key components: subcarrier selection, data calibration, signal extraction, and respiration and heart rate estimation. The performance of the BFF-based estimation algorithm is experimentally validated in several indoor environments using commodity IEEE 802.11ac devices. Results show that respiration rate and heart rate can be estimated with average errors below 1 breaths/min and 10 beats/min, respectively. Furthermore, accuracy comparisons between BFF-based and CSI-based estimations are provided to investigate the impact of lossy compression from CSI to BFF, specifically singular value decomposition (SVD) calculation and quantization. Comparisons reveal that the accuracy degradation of the BFF-based estimation compared to CSI-based estimation is primarily caused by the quantization rather than the SVD calculation.
- Open Access
- 8 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Vehicular Technology
- Vol. 5, 1024-1035
Beamforming Feedback-Based Line-of-Sight Identification Toward Firmware-Agnostic WiFi Sensing
This study realizes firmware-agnostic line-of-sight (LOS) identification to extend the range of WiFi-sensing applications. We developed a beamforming feedback (BFF)-based LOS identification algorithm. BFF frames are transmitted for multiple-input multiple-output (MIMO) communications. They can be obtained by capturing frames without custom firmware or specific chipsets and contain a beamforming feedback matrix (BFM) and subcarrier-averaged stream gain (SSG). These provide partial channel state information (CSI), and there are two major calculation steps involved from the CSI to the BFF: unquantized BFF (UQBFF) calculation and quantization. Focusing on the relationship between singular value decomposition and principal component analysis, we numerically demonstrated that the first column vectors of the BFM reflect the LOS/NLOS conditions. Therefore, the proposed BFF-based method extracts features from the first-column vectors of the BFM. In addition, SSGs were leveraged to improve the accuracy. To demonstrate the feasibility of the proposed method, we conducted experiments using commodity off-the-shelf devices compliant with the IEEE 802.11ac standard. In the experimental evaluation, the proposed BFF-based method achieved an identification accuracy of 75.0%, whereas the CSI-based method achieved an accuracy of 81.2%. Accuracy comparisons revealed that the accuracy degradation of the BFF-based identification from the CSI-based identification was primarily caused by UQBFF calculations rather than quantization.
- 8 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Vehicular Technology
- Vol. 5, 1024-1035
Open AccessBeamforming Feedback-Based Line-of-Sight Identification Toward Firmware-Agnostic WiFi Sensing
This study realizes firmware-agnostic line-of-sight (LOS) identification to extend the range of WiFi-sensing applications. We developed a beamforming feedback (BFF)-based LOS identification algorithm. BFF frames are transmitted for multiple-input multiple-output (MIMO) communications. They can be obtained by capturing frames without custom firmware or specific chipsets and contain a beamforming feedback matrix (BFM) and subcarrier-averaged stream gain (SSG). These provide partial channel state information (CSI), and there are two major calculation steps involved from the CSI to the BFF: unquantized BFF (UQBFF) calculation and quantization. Focusing on the relationship between singular value decomposition and principal component analysis, we numerically demonstrated that the first column vectors of the BFM reflect the LOS/NLOS conditions. Therefore, the proposed BFF-based method extracts features from the first-column vectors of the BFM. In addition, SSGs were leveraged to improve the accuracy. To demonstrate the feasibility of the proposed method, we conducted experiments using commodity off-the-shelf devices compliant with the IEEE 802.11ac standard. In the experimental evaluation, the proposed BFF-based method achieved an identification accuracy of 75.0%, whereas the CSI-based method achieved an accuracy of 81.2%. Accuracy comparisons revealed that the accuracy degradation of the BFF-based identification from the CSI-based identification was primarily caused by UQBFF calculations rather than quantization.