CYChenjun Yu

Chenjun Yu

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Chenjun Yu has a total of 19 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Hydrogen Embrittlement of 13%Ni Steel for Liquefied Hydrogen Tanks: Role of Reversed Austenite and Effect of Cryogenic Pre-Strain

    by Chenjun Yu, Tetsuya Namegawa, Teppei Ohkawa, Mitsuo Kimura, Tomoya Kawabata

    High-Ni steels are candidate materials for large-scale liquefied hydrogen (LH2) storage tanks. In service, these tanks may suffer hydrogen embrittlement (HE) during warm-up events, and the tank wall may undergo plastic straining at cryogenic temperatures. This study examined the HE behaviour of a quenched-lamellarized-tempered 13%Ni steel and the effect of cryogenic pre-strain on it, using slow strain rate tensile tests in 10 MPa gaseous hydrogen at room temperature together with thermal desorption analysis, silver decoration and SEM-EBSD. The as-received steel contained approximately 17% filmlike reversed austenite along lath and packet boundaries, which retained approximately 70% of the absorbed hydrogen. During straining in hydrogen, however, this austenite became unstable: at 3% strain, about 70% of it had transformed, compared with 16% in air. Interface microcracking and quasi-cleavage cracking along {110} planes were promoted in H2. The reduction of area reduced by 50.2%. A 5% pre-strain applied below 20 K transformed essentially all of the austenite before hydrogen exposure. As a result, the hydrogen-induced loss of reduction of area fell to 23.5%, and fracture changed to tortuous quasi-cleavage with dense tear ridges. However, pre-strain also raised the strength and caused earlier strain localization, so the elongation-based HE index increased with pre-strain, and the loss of reduction of area rose again to 36.2% after 10% pre-strain. These results show that the cryogenic strain history should be considered when assessing LH2 tanks.

  • Open Access

    Carbide-decorated grain boundary networks control hydrogen embrittlement of Ni–Mo weld metals: a comparison of GTAW and SAW

    by Chenjun Yu, Shohei Uranaka, Eita Tochigi, Miyuki Takeuchi, Ritsuki Morohoshi, Shuonan Chen, Mitsuo Kimura, Tomoya Kawabata

    Nickel–Mo (Hastelloy-type) filler metals are widely used to weld High Ni steel for liquefied hydrogen tank fabrication, yet the hydrogen embrittlement (HE) behavior of these solid-solution-strengthened weld metals (WMs) has received little attention. Here, GTAW and SAW WMs deposited from a nominally identical consumable were compared. Despite similar bulk composition, the two processes produced markedly different microstructures: GTAW, welded with a weaving technique, yielded finer, more randomly oriented grains together with carbide-poor equiaxed regions whose boundaries were densely decorated with M6C, whereas SAW, deposited without weaving, produced coarse, ⟨100⟩-textured columnar grains containing abundant coarse interdendritic Mo2C. Thermal desorption spectroscopy (TDS) and NanoSIMS showed that the carbides in both WMs are not strong hydrogen traps; hydrogen instead resides mainly in the lattice and at weak reversible sites such as grain boundaries and carbide/matrix interfaces, with the SAW WM absorbing about 30% more hydrogen overall. Slow strain rate tensile (SSRT) and constant-load CT tests in gaseous hydrogen revealed that the GTAW WM was far more susceptible to HE (reduction-of-area index Iψ = 81.7%) than the SAW WM (Iψ = 28.9%): failure in the GTAW WM occurred by decohesion along carbide-decorated grain boundaries that link into a connected, percolating crack network, whereas cracking at interdendritic carbides in the columnar SAW microstructure remained anisotropic and non-percolating. These results show that carbide morphology and distribution control HE resistance in Ni–Mo WMs, and that controlling the welding process to avoid carbide-decorated grain-boundary networks is more important than grain refinement for hydrogen-tank applications.

  • Open Access

    Hydrogen embrittlement behavior of SMAW nickel-based weld metal in 13%Ni steel: Dual role of NbC in hydrogen trapping and localized damage

    by Chenjun Yu, Shohei Uranaka, Eita Tochigi, Miyuki Takeuchi, Mitsuo Kimura, Tomoya Kawabata


  • Open Access

    Hydrogen Embrittlement Behavior of SMAW Nickel-Based Weld Metal in High-Ni Steel: Role of NbC in Hydrogen Trapping and Localized Damage

    by Chenjun Yu, Shohei Uranaka, Eita Tochigi, Miyuki Takeuchi, Mitsuo Kimura, Tomoya Kawabata

    The hydrogen embrittlement behavior of Shielded Metal Arc Welding (SMAW) nickel-based weld metal (WM) in high-Ni steel was systematically investigated. Microstructural characterization revealed that the WM mainly consists of columnar solidification grains with an average grain size of ~98.25 μm. Precipitates were identified as dispersed (Nb, Mo, Ti)C carbides and negligible Al2O3 and Laves. Hydrogen distribution was analyzed using silver decoration and Nano-scale secondary ion mass spectrometry (NanoSIMS), both consistently demonstrating strong hydrogen trapping at NbC precipitates. Slow strain rate testing (SSRT) conducted in a 10 MPa hydrogen environment showed only moderate degradation in mechanical properties, with a slight reduction in yield strength (~5%) and a limited decrease in ductility. Fractographic analysis indicated that ductile dimples remain dominant, although localized cleavage cracks and increased microcrack density were observed under hydrogen exposure. Electron backscatter diffraction (EBSD) analysis revealed no significant difference in geometrically necessary dislocation (GND) density between air and hydrogen environments. Crack initiation was consistently observed within NbC precipitates. The degree of crack initiation and propagation were strengthened by hydrogen. The results indicate that the high density of NbC precipitates effectively suppressed severe embrittlement.

  • Open Access

    Susceptibility to hydrogen embrittlement in welded joints at ambient temperature for liquefied hydrogen storage tanks

    by Chenjun Yu, Yu Yoshino, Yuji Abiru, Hiroshi Tsujigami, Xixian Li, Shohei Uranaka, Mitsuo Kimura, Tomoya Kawabata

    Liquefied hydrogen storage tanks are poised to play a pivotal role in the realization of a carbon–neutral society. While stainless steel is considered the material of choice for the first 50,000-m 3 tank, there is a potential for carbon steel to be employed as the inner tank material in the future to increase capacity. The welding materials combined with the carbon steel are expected to be Hastelloy and Inconel alloys, which are currently used in LNG (liquefied natural gas) tank construction. However, since some reports have shown that the effect of Ni on hydrogen embrittlement properties deteriorates significantly on the high-Ni side, we conducted evaluation tests that took into account the operating environment. The SSRT (slow strain rate testing) revealed that the GTAW (gas tungsten arc welding) weld metal exhibited severe hydrogen embrittlement, whereas no significant crack propagation was observed in the constant-load CT (compact tension) tests. We analyzed the discrepancies between the two experimental methods and concluded that the differences are largely related to pre-straining and hydrogen diffusion and accumulation. From a FFS (fitness for service) perspective, the results of the CT tests are considered more representative of real-world conditions, indicating that this material combination is suitable for use in liquid hydrogen storage tanks.


  • Open Access

    Influence of welding methods on the microstructure of nickel-based weld metal for liquid hydrogen tanks

    by Chenjun Yu, Tomoya Kawabata, Shigetoshi Kyouno, Xixian Li, Shohei Uranaka, Daiki Maeda

    This study investigates the microstructure and hardness of weld metals used in liquid hydrogen storage tanks, with a focus on the effects of three welding methods: Gas Tungsten Arc Welding (GTAW), Submerged Arc Welding (SAW), and Shielded Metal Arc Welding (SMAW). Finite element simulations were employed to model the temperature field during welding, aiding in the explanation of observed microstructural differences. The results show that while GTAW and SMAW produce weld metals with similar microstructures, SAW generates significantly larger grains with a pronounced preferential orientation. The use of weaving techniques play a key role in shaping the solidification microstructures. Additionally, the hardness of the weld metal is comparable to that of the base material, with a slight reduction corresponding to increased grain size. This research offers valuable insights into optimizing welding processes for liquid hydrogen storage tanks by addressing the microstructural characteristics that influence weld joint performance. Graphical Abstract


  • Hydrogen-enhanced corrosion behaviour of Cu-doping low-alloy steels through corrosion tests and first-principles calculations

    by Chenjun Yu, Yi Wang, Tianyi Zhang

    This study examines the crucial role played by Cu in electrochemical corrosion under marine and hydrogen-coupled environments. The adsorption energies of hydrogen and chlorine at different surface sites of α-Fe and Cu-doped α-Fe were analysed using first-principles computations. A significant increase in adsorption energies introduced by Cu was discovered and evidenced by shifts in electrochemical polarisation curves, corresponding with the corrosion morphologies. Moreover, we delve into the effects of Cu on hydrogen solubility and diffusion within the steel, showing that Cu atoms affect hydrogen transport by altering the energy barriers and forming precipitates. These comprehensive insights provide a deeper understanding of the role of Cu doping in enhancing the performance and durability of Ni-containing steels in corrosive and hydrogen-prone environments, offering valuable guidelines for material design and application in industrial settings.