Peng-Xu Zhu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Peng-Xu Zhu has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Jian-Xin Chen
Nantong University
3 shared publications - Xu Shi
School of Information Science and Technology, Nantong University, Nantong, China
2 shared publications - Shi-Chang Tang
School of Information Science and Technology, Nantong University, Nantong, China
1 shared publication - Wei Qin
School of Information Science and Technology, Nantong University, Nantong, China
1 shared publication - Yongjie Yang
Nantong University
1 shared publication
Latest Publications
- 29 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. PP (2771957X) , 1-4
Dual-Wideband High-Selectivity BPF Based on Fundamental and High-Order Modes of Ridge WG SSPPs
This article presents a novel ridge waveguide (WG) spoof surface plasmon polariton (SSPP) structure that simultaneously supports fundamental and high-order modes for designing a dual-band bandpass filter (BPF). The proposed SSPP unit achieves relatively independent control of the two passbands’ cutoff frequencies by loading three pairs of metal stubs onto the vertical-grooved ridge WG. Through structural optimization, the specific positions of each stub pair are precisely determined, enabling selective mode tuning by strategically placing stubs in the corresponding strong-field region. To enhance passband selectivity, the filter incorporates folded slots at both ends of the central ridge, forming quarter-wavelength ( $\lambda $ /4) resonators and then introducing transmission zeros (TZs) below each passband from their fundamental resonance and first harmonic. For demonstration purposes, the BPF prototypes were fabricated and measured. Simulated and experimental results show good agreement.
- 29 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. PP (2771957X) , 1-4
Dual-Wideband High-Selectivity BPF Based on Fundamental and High-Order Modes of Ridge WG SSPPs
This article presents a novel ridge waveguide (WG) spoof surface plasmon polariton (SSPP) structure that simultaneously supports fundamental and high-order modes for designing a dual-band bandpass filter (BPF). The proposed SSPP unit achieves relatively independent control of the two passbands’ cutoff frequencies by loading three pairs of metal stubs onto the vertical-grooved ridge WG. Through structural optimization, the specific positions of each stub pair are precisely determined, enabling selective mode tuning by strategically placing stubs in the corresponding strong-field region. To enhance passband selectivity, the filter incorporates folded slots at both ends of the central ridge, forming quarter-wavelength ( $\lambda $ /4) resonators and then introducing transmission zeros (TZs) below each passband from their fundamental resonance and first harmonic. For demonstration purposes, the BPF prototypes were fabricated and measured. Simulated and experimental results show good agreement.
- 18 March 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 35 (5) , 521-524
A Ridge WG SSPP Bandpass Filter With Lower Transmission Zero and Extended Upper Stopband
This article proposes a novel design method for introducing a lower transmission zero (TZ) in a ridge waveguide (WG) spoof surface plasmon polariton (SSPP) bandpass filter (BPF). Initially, the inverted T-shaped slots are etched on the central ridge to construct the SSPP and then design a wideband BPF, and the upper and lower cutoff frequencies of passband are determined by the SSPP and double gratings (DGs) on both sides of the ridge WG. To improve the rejection roll-off of the lower stopband, a pair of folded slots are etched at both ends of the ridge to form a quarter-wavelength (λ/4) resonance for introducing a TZ below the passband without increasing the size. Additionally, the stopband of the proposed SSPP filter can be extended by optimizing the DGs to suppress the higher order modes of the SSPP. To demonstrate this method, a ridge WG BPF was fabricated and measured. The measurement results indicate that the filter possesses favorable frequency selectivity and a wide stopband.
- 18 March 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 35 (5) , 521-524
A Ridge WG SSPP Bandpass Filter With Lower Transmission Zero and Extended Upper Stopband
This article proposes a novel design method for introducing a lower transmission zero (TZ) in a ridge waveguide (WG) spoof surface plasmon polariton (SSPP) bandpass filter (BPF). Initially, the inverted T-shaped slots are etched on the central ridge to construct the SSPP and then design a wideband BPF, and the upper and lower cutoff frequencies of passband are determined by the SSPP and double gratings (DGs) on both sides of the ridge WG. To improve the rejection roll-off of the lower stopband, a pair of folded slots are etched at both ends of the ridge to form a quarter-wavelength (λ/4) resonance for introducing a TZ below the passband without increasing the size. Additionally, the stopband of the proposed SSPP filter can be extended by optimizing the DGs to suppress the higher order modes of the SSPP. To demonstrate this method, a ridge WG BPF was fabricated and measured. The measurement results indicate that the filter possesses favorable frequency selectivity and a wide stopband.
- 22 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 34 (10) , 1151-1154
A Compact Low-Loss Bandpass Filter Using Spoof Surface Plasmon Polaritons in a Ridge Waveguide
This article investigates a spoof surface plasmon polariton (SSPP) first by etching the inverted T-shaped slot on the central ridge of the ridge waveguide (WG) for constructing a low-loss bandpass filter (BPF). To achieve flexible bandwidth, the upper and lower edges of the passband can be controlled independently by the SSPP and double gratings (DGs) on both sides of the ridge WG. Furthermore, the lower impedance of the ridge WG allows it to be directly connected to the coaxial connector to achieve a compact size. To validate the approach, an $X$ -band ridge WG BPF is fabricated with a measured bandwidth of 7.9–12.2 GHz. The good agreement between simulation and measurement results demonstrates the method’s advantages of small size, flexible controlling of bandwidth, and low insertion loss (IL) of 0.23 dB.
- 22 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 34 (10) , 1151-1154
A Compact Low-Loss Bandpass Filter Using Spoof Surface Plasmon Polaritons in a Ridge Waveguide
This article investigates a spoof surface plasmon polariton (SSPP) first by etching the inverted T-shaped slot on the central ridge of the ridge waveguide (WG) for constructing a low-loss bandpass filter (BPF). To achieve flexible bandwidth, the upper and lower edges of the passband can be controlled independently by the SSPP and double gratings (DGs) on both sides of the ridge WG. Furthermore, the lower impedance of the ridge WG allows it to be directly connected to the coaxial connector to achieve a compact size. To validate the approach, an $X$ -band ridge WG BPF is fabricated with a measured bandwidth of 7.9–12.2 GHz. The good agreement between simulation and measurement results demonstrates the method’s advantages of small size, flexible controlling of bandwidth, and low insertion loss (IL) of 0.23 dB.