Andrej Seljak
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Andrej Seljak has a total of 144 co-authors. Here are the top co-authors by number of shared publications:
- Peter Krizan
Jožef Stefan Institute, Ljubljana, Slovenia
15 shared publications - Rok Pestotnik
Jozef Stefan Institute
15 shared publications - Samo Korpar
Faculty of Chemistry and Chemical Engineering, University of Maribor, Smetanova ulica 17, Maribor, 2000
13 shared publications - Rok Dolenec
Jozef Stefan Institute
9 shared publications - Shohei Nishida
Institute of Particle and Nuclear Studies KEK Tsukuba Japan
5 shared publications A. Lozar
4 shared publications
Latest Publications
- Open Access
- 1 May 2026
- Published by IOP Publishing in Journal of Instrumentation
- Vol. 21 (05) , C05020
Radiation hardness characterization of silicon photomultipliers for next-generation particle identification detectors
Silicon photomultipliers (SiPMs) are promising candidates for the new photon detectors of the Ring Imaging Cherenkov (RICH) detector in the LHCb experiment at CERN. With the increased luminosity of the High-Luminosity LHC, the RICH photon detector must be upgraded to handle higher photon overlap and improved spatial granularity, while also withstanding greater doses of radiation. The radiation tolerance of SiPMs remains a key challenge for their use in high-energy physics, motivating extensive research. This work investigates the effects of cryogenic temperatures on single-photon detection in neutron-irradiated SiPMs based on NUV-HD-MT (metal-in-trench) technology, using low-field, and ultra-low-field variants. The results demonstrate that cryogenic cooling can mitigate the impact of neutron induced damage at fluences up to 1 × 10 12 n eq /cm 2 and recover the single-photon resolution.
- 1 May 2026
- Published by IOP Publishing in Journal of Instrumentation
- Vol. 21 (05) , C05020
Open AccessRadiation hardness characterization of silicon photomultipliers for next-generation particle identification detectors
Silicon photomultipliers (SiPMs) are promising candidates for the new photon detectors of the Ring Imaging Cherenkov (RICH) detector in the LHCb experiment at CERN. With the increased luminosity of the High-Luminosity LHC, the RICH photon detector must be upgraded to handle higher photon overlap and improved spatial granularity, while also withstanding greater doses of radiation. The radiation tolerance of SiPMs remains a key challenge for their use in high-energy physics, motivating extensive research. This work investigates the effects of cryogenic temperatures on single-photon detection in neutron-irradiated SiPMs based on NUV-HD-MT (metal-in-trench) technology, using low-field, and ultra-low-field variants. The results demonstrate that cryogenic cooling can mitigate the impact of neutron induced damage at fluences up to 1 × 10 12 n eq /cm 2 and recover the single-photon resolution.
- Open Access
- 1 April 2026
- Published by IOP Publishing in Journal of Instrumentation
- Vol. 21 (04) , C04086
GRAPH readout ASIC for large aperture, high resolution single photon imaging detectors designated for space applications
Large aperture, high resolution, single photon imaging detectors are in high demand for future space explorations like the Habitable Worlds Observatory (HWO), which targets include the search of habitable exoplanets. Advancing the Technology Readiness Level (TRL) for such detector candidates toward completion (9-operational and flying in space), is a challenging endeavor. This paper reports on a decade of progress in the development of crossed strip (XS) readout systems employing microchannel plates (MCPs) for signal amplification, and provides an overview of recent ASIC architectures and related electronic components. To complement the content, some detector implementation details, and current results obtained operating the ASICs on the detector are provided.
- 1 April 2026
- Published by IOP Publishing in Journal of Instrumentation
- Vol. 21 (04) , C04086
Open AccessGRAPH readout ASIC for large aperture, high resolution single photon imaging detectors designated for space applications
Large aperture, high resolution, single photon imaging detectors are in high demand for future space explorations like the Habitable Worlds Observatory (HWO), which targets include the search of habitable exoplanets. Advancing the Technology Readiness Level (TRL) for such detector candidates toward completion (9-operational and flying in space), is a challenging endeavor. This paper reports on a decade of progress in the development of crossed strip (XS) readout systems employing microchannel plates (MCPs) for signal amplification, and provides an overview of recent ASIC architectures and related electronic components. To complement the content, some detector implementation details, and current results obtained operating the ASICs on the detector are provided.
- Open Access
- 14 March 2026
- Published by Elsevier in Nuclear Instruments and Methods in Physics Research Section A: Accelerators, Spectrometers, Detectors and Associated Equipment
- Vol. 1088
Characterization of the LAPPD, a large area microchannel-plate PMT
- 14 March 2026
- Published by Elsevier in Nuclear Instruments and Methods in Physics Research Section A: Accelerators, Spectrometers, Detectors and Associated Equipment
- Vol. 1088
Open AccessCharacterization of the LAPPD, a large area microchannel-plate PMT
- Open Access
- 5 March 2026
- Published by Elsevier in Nuclear Instruments and Methods in Physics Research Section A: Accelerators, Spectrometers, Detectors and Associated Equipment
- Vol. 1087
Operation and performance of the Belle II Aerogel RICH detector
- 5 March 2026
- Published by Elsevier in Nuclear Instruments and Methods in Physics Research Section A: Accelerators, Spectrometers, Detectors and Associated Equipment
- Vol. 1087
Open AccessOperation and performance of the Belle II Aerogel RICH detector
- Open Access
- 1 June 2025
- Published by IOP Publishing in Journal of Instrumentation
- Vol. 20 (06) , P06052
SiPM and CMOS SPAD characterization at liquid nitrogen temperatures
A number of high energy physics and cosmology experiments use or plan to use single-photon avalanche diodes (SPADs) or SPAD based silicon photomultipliers (SiPMs) in harsh conditions, such as cryogenic temperatures and/or high radiation environments. In this contribution, studies of the operation of SPADs and front-end electronics at temperatures down to liquid nitrogen is presented. SPADs designed by EPFL AQUA Lab in 55 nm and 110 nm CMOS technology were tested at different temperatures between room temperature and liquid nitrogen. Some of the SPAD samples were neutron irradiated with fluences up to 1012 1-MeV neutron equivalent/cm2. The characterization included direct count rate measurements at different thresholds (threshold scans), in the dark and at low-light illumination by way of picosecond laser. The results of this work will be used to inform the photodetector design considerations in the planned Upgrade II of the LHCb ring imaging Cherenkov counter (RICH).
- 1 June 2025
- Published by IOP Publishing in Journal of Instrumentation
- Vol. 20 (06) , P06052
Open AccessSiPM and CMOS SPAD characterization at liquid nitrogen temperatures
A number of high energy physics and cosmology experiments use or plan to use single-photon avalanche diodes (SPADs) or SPAD based silicon photomultipliers (SiPMs) in harsh conditions, such as cryogenic temperatures and/or high radiation environments. In this contribution, studies of the operation of SPADs and front-end electronics at temperatures down to liquid nitrogen is presented. SPADs designed by EPFL AQUA Lab in 55 nm and 110 nm CMOS technology were tested at different temperatures between room temperature and liquid nitrogen. Some of the SPAD samples were neutron irradiated with fluences up to 1012 1-MeV neutron equivalent/cm2. The characterization included direct count rate measurements at different thresholds (threshold scans), in the dark and at low-light illumination by way of picosecond laser. The results of this work will be used to inform the photodetector design considerations in the planned Upgrade II of the LHCb ring imaging Cherenkov counter (RICH).
- Open Access
- 1 June 2025
- Published by IOP Publishing in Journal of Instrumentation
- Vol. 20 (06) , C06033
Radiation hardness and annealing study of neutron-irradiated silicon photomultipliers
Silicon photomultipliers (SiPMs) are semiconductor photodetectors increasingly used in high-energy physics experiments. In the planned upgrade of the Large Hadron Collider beauty (LHCb) experiment, they are considered to be used to detect Cherenkov photons in the Ring Imaging Cherenkov (RICH) detectors. In this application, the biggest drawback of current SiPMs is their susceptibility to radiation damage, where the dark count rate (DCR), typically on the order of 105 Hz/mm2 at room temperature, significantly increases proportionally with the irradiation fluence, which hinders the single photon detection beyond fluence of 109 neq/cm2. In this work, 3 × 3 mm2 SiPMs from different producers and cell sizes, Hamamatsu (50 μm, S13360-3050PE), Ketek (25 μm, PM3325-WB and 50 μm, PM3350-EB), AdvanSiD (40 μm, NUV3S-P and RGB3S-P), SensL (35 μm, MicroFJ-30035), a 3.7 × 3.7 mm2 SiPM from Broadcom (30 μm, AFBR-S4N44C013), and a 1 × 1 mm2 SiPM from SensL (35 μm, MicroRA-10035) were characterized. The SiPMs were irradiated at the Jožef Stefan Institute TRIGA nuclear reactor with fluences from 109 neq/cm2 up to 1013 neq/cm2. The main objective was to determine the temperature at which irradiated SiPMs can still meet minimal performance requirements in future RICH detectors. The influence of the high-temperature annealing on SiPM performance post-irradiation was also investigated. For the SiPM characterization in all the cases, current-voltage (I-V curve) measurements, DCR measurements, and waveform analysis, including single photon time resolution (SPTR), were carried out at controlled temperature steps from room temperature down to the liquid nitrogen temperature. As a result, through a combination of annealing and cooling, 2 of the SiPMs withstood the highest irradiation fluence of 1013 neq/cm2 with an SPTR of about 200 ps.
- 1 June 2025
- Published by IOP Publishing in Journal of Instrumentation
- Vol. 20 (06) , C06033
Open AccessRadiation hardness and annealing study of neutron-irradiated silicon photomultipliers
Silicon photomultipliers (SiPMs) are semiconductor photodetectors increasingly used in high-energy physics experiments. In the planned upgrade of the Large Hadron Collider beauty (LHCb) experiment, they are considered to be used to detect Cherenkov photons in the Ring Imaging Cherenkov (RICH) detectors. In this application, the biggest drawback of current SiPMs is their susceptibility to radiation damage, where the dark count rate (DCR), typically on the order of 105 Hz/mm2 at room temperature, significantly increases proportionally with the irradiation fluence, which hinders the single photon detection beyond fluence of 109 neq/cm2. In this work, 3 × 3 mm2 SiPMs from different producers and cell sizes, Hamamatsu (50 μm, S13360-3050PE), Ketek (25 μm, PM3325-WB and 50 μm, PM3350-EB), AdvanSiD (40 μm, NUV3S-P and RGB3S-P), SensL (35 μm, MicroFJ-30035), a 3.7 × 3.7 mm2 SiPM from Broadcom (30 μm, AFBR-S4N44C013), and a 1 × 1 mm2 SiPM from SensL (35 μm, MicroRA-10035) were characterized. The SiPMs were irradiated at the Jožef Stefan Institute TRIGA nuclear reactor with fluences from 109 neq/cm2 up to 1013 neq/cm2. The main objective was to determine the temperature at which irradiated SiPMs can still meet minimal performance requirements in future RICH detectors. The influence of the high-temperature annealing on SiPM performance post-irradiation was also investigated. For the SiPM characterization in all the cases, current-voltage (I-V curve) measurements, DCR measurements, and waveform analysis, including single photon time resolution (SPTR), were carried out at controlled temperature steps from room temperature down to the liquid nitrogen temperature. As a result, through a combination of annealing and cooling, 2 of the SiPMs withstood the highest irradiation fluence of 1013 neq/cm2 with an SPTR of about 200 ps.
- Open Access
- 1 March 2025
- Published by IOP Publishing in Journal of Instrumentation
- Vol. 20 (03) , P03034
LHCb RICH Fast-timing photon detection at the SPS charged particle beam
The use of a new optoelectronic readout chain with 𝒪(100)ps time resolution is a major milestone in the development of RICH detectors for environments with a high number of particle interactions per bunch crossing, such as the High-Luminosity LHC. A prototype chain, based on MAPMT and SiPM photon sensors coupled to readout electronics integrating the FastIC ASIC and a TDC-in-FPGA, is presented. The FastIC is an 8-channel ASIC for analogue-to-digital conversion with 25 ps time resolution. This ASIC is the predecessor of the FastRICH ASIC for the LHCb RICH upgrades. The signals from the photon detectors are timestamped in a custom multi-channel TDC-in-FPGA designed using a multi-phase clock sampling architecture with an average bin width of 150 ps. The prototype optoelectronic readout chain was tested in a charged particle beam of 180 GeV/c hadrons at the CERN SPS facility. The reference time-of-arrival of the particle tracks was measured with about 100 ps time resolution and the number of tracks per event was registered using a particle tracking system. The single-photon time resolution of the MAPMT sensors is extracted using a binned method in order to correct for the calibrated TDC bin widths and detector time-walk. The resulting best estimate of σ = 182 ± 24 ps is in agreement with pulsed-laser measurements in the lab and consistent with the expectations from the manufacturer.
- 1 March 2025
- Published by IOP Publishing in Journal of Instrumentation
- Vol. 20 (03) , P03034
Open AccessLHCb RICH Fast-timing photon detection at the SPS charged particle beam
The use of a new optoelectronic readout chain with 𝒪(100)ps time resolution is a major milestone in the development of RICH detectors for environments with a high number of particle interactions per bunch crossing, such as the High-Luminosity LHC. A prototype chain, based on MAPMT and SiPM photon sensors coupled to readout electronics integrating the FastIC ASIC and a TDC-in-FPGA, is presented. The FastIC is an 8-channel ASIC for analogue-to-digital conversion with 25 ps time resolution. This ASIC is the predecessor of the FastRICH ASIC for the LHCb RICH upgrades. The signals from the photon detectors are timestamped in a custom multi-channel TDC-in-FPGA designed using a multi-phase clock sampling architecture with an average bin width of 150 ps. The prototype optoelectronic readout chain was tested in a charged particle beam of 180 GeV/c hadrons at the CERN SPS facility. The reference time-of-arrival of the particle tracks was measured with about 100 ps time resolution and the number of tracks per event was registered using a particle tracking system. The single-photon time resolution of the MAPMT sensors is extracted using a binned method in order to correct for the calibrated TDC bin widths and detector time-walk. The resulting best estimate of σ = 182 ± 24 ps is in agreement with pulsed-laser measurements in the lab and consistent with the expectations from the manufacturer.
- Open Access
- 1 January 2025
- Published by IOP Publishing in Journal of Instrumentation
- Vol. 20 (01) , T01001
GRAPH — an readout ASIC for large MCP based detectors
We present a programmable 16 channel, mixed signal, low power readout ASIC, having the project historically named Gigasample Recorder of Analog waveforms from a PHotodetector (GRAPH). It is designed to read large aperture single photon imaging detectors using micro channel plates for charge multiplication, and measuring the detector's response on crossed strips anodes to extrapolate the incoming photon position. Each channel consists of a fast, low power and low noise charge sensitive amplifier, which provides a myriad of coarse and fine programmable options for gain and shaping settings. Further, the amplified signal is recorded using, to our knowledge novel, the Hybrid Universal sampLing Architecture (HULA) ADC. A kind of mixed signal double buffer memory, that enables concurrent waveform recording, and selected event digitized data extraction. The sampling frequency is freely adjustable between few kHz up to 125 MHz, while the chip's internal digital memory holds a history 2048 samples for each channel, with a digital headroom of 12 bits. An optimized region of interest sample-read algorithm allows to extract the information just around the event pulse peak, while selecting the next event, thus substantially reducing the operational dead time. The chip is designed in 130 nm TSMC CMOS technology, and its power consumption is around 47 mW per channel.
- 1 January 2025
- Published by IOP Publishing in Journal of Instrumentation
- Vol. 20 (01) , T01001
Open AccessGRAPH — an readout ASIC for large MCP based detectors
We present a programmable 16 channel, mixed signal, low power readout ASIC, having the project historically named Gigasample Recorder of Analog waveforms from a PHotodetector (GRAPH). It is designed to read large aperture single photon imaging detectors using micro channel plates for charge multiplication, and measuring the detector's response on crossed strips anodes to extrapolate the incoming photon position. Each channel consists of a fast, low power and low noise charge sensitive amplifier, which provides a myriad of coarse and fine programmable options for gain and shaping settings. Further, the amplified signal is recorded using, to our knowledge novel, the Hybrid Universal sampLing Architecture (HULA) ADC. A kind of mixed signal double buffer memory, that enables concurrent waveform recording, and selected event digitized data extraction. The sampling frequency is freely adjustable between few kHz up to 125 MHz, while the chip's internal digital memory holds a history 2048 samples for each channel, with a digital headroom of 12 bits. An optimized region of interest sample-read algorithm allows to extract the information just around the event pulse peak, while selecting the next event, thus substantially reducing the operational dead time. The chip is designed in 130 nm TSMC CMOS technology, and its power consumption is around 47 mW per channel.