Alexander E. Nikonov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Alexander E. Nikonov has a total of 60 co-authors. Here are the top co-authors by number of shared publications:
- Evgenii S. Kersnovsky
Voronezh State University, 1 Universitetskaya pl., Voronezh 394018, Russian Federation
4 shared publications - G. P. Potudanskii
Voronezh State Univ, Dept Solid State & Nanostruct Phys, Voronezh, Russia
4 shared publications - Ivan V. Polshin
Voronezh State University
4 shared publications - Konstantin Alexandrovich Barkov
Voronezh State University, Voronezh, Russia
4 shared publications - Yaroslav A. Peshkov
Voronezh State University
4 shared publications - Aleksandr Viktorovich Sitnikov
Voronezh State Technical University, Voronezh, Russia
3 shared publications
Latest Publications
- 31 August 2026
- Published by EDP Sciences in The European Physical Journal Applied Physics
- Vol. 101, 17
Influence of morphology on electronic transport in amorphous Fe x Si 1− x alloy thin films
A central challenge in spintronics is the development of materials for efficient spin-polarized current generation. While crystalline Heusler alloys often fall short of predicted half-metallicity due to structural disorder, their amorphous analogs present a promising avenue. In this work, we investigate how the composition-dependent structural evolution of short-range order controls room temperature electronic transport in amorphous Fe x Si 1− x (0.44 ≤ x ≤ 0.75) alloy thin films. This structural evolution, revealed by X-ray reflectivity, underpins a transition from hopping to metallic conduction across distinct amorphous phases (FeSi → Fe 2 Si → Fe 3 Si). In the FeSi-like phase region, electronic transport is governed by Mott variable-range hopping, resulting in high resistivity and low Hall mobility. The onset of metallic conduction within the amorphous Fe 2 Si- and Fe 3 Si-like composition ranges yields lower resistivity alongside enhanced hole mobility. Our results establish a direct structure-property relationship in amorphous Fe x Si 1− x alloys, demonstrating the ability to selectively design electronic transport through fine compositional tuning. Understanding the interplay between local atomic order and electronic transport in amorphous Fe–Si alloys provides key insights for engineering next-generation spintronic devices.
- 31 August 2026
- Published by EDP Sciences in The European Physical Journal Applied Physics
- Vol. 101, 17
Influence of morphology on electronic transport in amorphous Fe x Si 1− x alloy thin films
A central challenge in spintronics is the development of materials for efficient spin-polarized current generation. While crystalline Heusler alloys often fall short of predicted half-metallicity due to structural disorder, their amorphous analogs present a promising avenue. In this work, we investigate how the composition-dependent structural evolution of short-range order controls room temperature electronic transport in amorphous Fe x Si 1− x (0.44 ≤ x ≤ 0.75) alloy thin films. This structural evolution, revealed by X-ray reflectivity, underpins a transition from hopping to metallic conduction across distinct amorphous phases (FeSi → Fe 2 Si → Fe 3 Si). In the FeSi-like phase region, electronic transport is governed by Mott variable-range hopping, resulting in high resistivity and low Hall mobility. The onset of metallic conduction within the amorphous Fe 2 Si- and Fe 3 Si-like composition ranges yields lower resistivity alongside enhanced hole mobility. Our results establish a direct structure-property relationship in amorphous Fe x Si 1− x alloys, demonstrating the ability to selectively design electronic transport through fine compositional tuning. Understanding the interplay between local atomic order and electronic transport in amorphous Fe–Si alloys provides key insights for engineering next-generation spintronic devices.
- 27 August 2026
- Published by Pleiades Publishing Ltd in Bulletin of the Russian Academy of Sciences: Physics
- Vol. 90 (8) , 1348-1354
Effect of a-Si and Ta2O5 Interlayers on the Current–Voltage Nonlinearity in Capacitor‑Type Cu/(CO40Fe40B20)x(SiO2)100–x/LiNbO3/Cr/Cu/Cr Memristors
We studied the influence of a-Si and Ta2O5 interlayers on resistive switching processes, the nonlinearity of current–voltage characteristics in the induced low-resistance state, and conductivity mechanisms as a function of the current flowing through the investigated structures. The origins of the nonlinearity of the current–voltage characteristics were examined, and the limiting charge transport mechanisms in the fabricated structures were identified.
- 27 August 2026
- Published by Pleiades Publishing Ltd in Bulletin of the Russian Academy of Sciences: Physics
- Vol. 90 (8) , 1348-1354
Effect of a-Si and Ta2O5 Interlayers on the Current–Voltage Nonlinearity in Capacitor‑Type Cu/(CO40Fe40B20)x(SiO2)100–x/LiNbO3/Cr/Cu/Cr Memristors
We studied the influence of a-Si and Ta2O5 interlayers on resistive switching processes, the nonlinearity of current–voltage characteristics in the induced low-resistance state, and conductivity mechanisms as a function of the current flowing through the investigated structures. The origins of the nonlinearity of the current–voltage characteristics were examined, and the limiting charge transport mechanisms in the fabricated structures were identified.
- Open Access
- 24 February 2026
- Published by Elsevier in SSRN Electronic Journal
Effect of Niobium Content on the Phase Composition of NbxSi100-x Films Fabricated by Ion-Beam Sputtering
Nb-Si films containing the Nb3Si phase (A15 structure) are a promising material for creating sensitive elements of superconducting single-photon IR radiation detectors. However, as a rule, Nb-Si thin films are amorphous or nanocrystalline and have an inhomogeneous phase composition. In turn, the diagnosis of nanocrystalline and amorphous films is a difficult task. Therefore, this work is devoted to studying the phase composition of NbxSi100-x films using ultra-soft X-ray emission spectroscopy and X-ray reflectivity, which are sensitive to amorphous phases. As a result of comprehensive studies, it has been shown that NbxSi100-x films contains phases NbSi2 and Nb3Si. At the same time, with an increase in the niobium content from 32 to 68 at.%, the NbSi2 : Nb3Si phase ratio changes from 2 : 1 to 1 : 3, respectively.
- 24 February 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessEffect of Niobium Content on the Phase Composition of NbxSi100-x Films Fabricated by Ion-Beam Sputtering
Nb-Si films containing the Nb3Si phase (A15 structure) are a promising material for creating sensitive elements of superconducting single-photon IR radiation detectors. However, as a rule, Nb-Si thin films are amorphous or nanocrystalline and have an inhomogeneous phase composition. In turn, the diagnosis of nanocrystalline and amorphous films is a difficult task. Therefore, this work is devoted to studying the phase composition of NbxSi100-x films using ultra-soft X-ray emission spectroscopy and X-ray reflectivity, which are sensitive to amorphous phases. As a result of comprehensive studies, it has been shown that NbxSi100-x films contains phases NbSi2 and Nb3Si. At the same time, with an increase in the niobium content from 32 to 68 at.%, the NbSi2 : Nb3Si phase ratio changes from 2 : 1 to 1 : 3, respectively.
- Open Access
- 3 February 2026
- Published by Elsevier in SSRN Electronic Journal
Effect of Niobium Content on the Phase Composition of NbxSi100-x Films Fabricated by Ion-Beam Sputtering
Nb-Si films containing the Nb3Si phase (A15 structure) are a promising material for creating sensitive elements of superconducting single-photon IR radiation detectors. However, as a rule, Nb-Si thin films are amorphous or nanocrystalline and have an inhomogeneous phase composition. In turn, the diagnosis of nanocrystalline and amorphous films is a difficult task. Therefore, this work is devoted to studying the phase composition of NbxSi100-x films using ultra-soft X-ray emission spectroscopy and X-ray reflectivity, which are sensitive to amorphous phases. As a result of comprehensive studies, it has been shown that NbxSi100-x films contains phases NbSi2 and Nb3Si. At the same time, with an increase in the niobium content from 32 to 68 at.%, the NbSi2 : Nb3Si phase ratio changes from 2 : 1 to 1 : 3, respectively.
- 3 February 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessEffect of Niobium Content on the Phase Composition of NbxSi100-x Films Fabricated by Ion-Beam Sputtering
Nb-Si films containing the Nb3Si phase (A15 structure) are a promising material for creating sensitive elements of superconducting single-photon IR radiation detectors. However, as a rule, Nb-Si thin films are amorphous or nanocrystalline and have an inhomogeneous phase composition. In turn, the diagnosis of nanocrystalline and amorphous films is a difficult task. Therefore, this work is devoted to studying the phase composition of NbxSi100-x films using ultra-soft X-ray emission spectroscopy and X-ray reflectivity, which are sensitive to amorphous phases. As a result of comprehensive studies, it has been shown that NbxSi100-x films contains phases NbSi2 and Nb3Si. At the same time, with an increase in the niobium content from 32 to 68 at.%, the NbSi2 : Nb3Si phase ratio changes from 2 : 1 to 1 : 3, respectively.
- 24 December 2025
- Published by Elsevier in Thin Solid Films
- Vol. 833
Silicon-induced phase evolution and electrical switching in AgxSi1-x nanocomposite films synthesized by ion-beam sputtering
- 24 December 2025
- Published by Elsevier in Thin Solid Films
- Vol. 833
Silicon-induced phase evolution and electrical switching in AgxSi1-x nanocomposite films synthesized by ion-beam sputtering
- Open Access
- 25 September 2025
- Published by Voronezh State University in Kondensirovannye sredy i mezhfaznye granitsy = Condensed Matter and Interphases
- Vol. 27 (3) , 398-408
Mechanical Properties of Li-Nb-O System Films
Objective: To quantitatively assess the hardness, elasticity, and plasticity, and to determine the influence of structure and substructure on these parameters in Li-Nb-O system films.Experimental: Li-Nb-O system films with a thickness of ~0.8 μm were grown on non-heated substrates (oxidized single-crystal silicon wafers (SiO₂ layer ~0.4 μm), single-crystal lithium niobate with (0001) orientation) by ion beam sputtering of a lithium niobate target. Thermal annealing of Li-Nb-O films on substrates was performed in air for 10 min (until complete crystallization) at temperatures of 550, 650, 700, 750, 800, and 850 °C. The heterostructures (film/substrate) were cooled with the furnace. The phase composition of the films was investigated by X-ray diffraction (XRD) and selected area electron diffraction (SAED). The substructure was studied by transmission electron microscopy (TEM) and high-resolution TEM (HRTEM, Tecnai G2 30ST) of cross-sectional specimens prepared by ion milling using a Quanta 3D setup. The surface morphology was investigated by scanning electron microscopy (SEM, Teskan Mira) in the topologicalcontrast mode and atomic force microscopy (AFM, Solver47). Mechanical properties – hardness (H) and Young's modulus (E) – were determined from nanoindentation (NI, NanoHardness Tester CSM Instruments) measurements using a Berkovich diamond indenter under the following conditions: maximum load 10 mN, loading rate 10 mN/min, and unloading rate 15 mN/min. Results: It was found that thermal annealing in an oxygen-containing atmosphere at 750°C induces crystallization of quasi-amorphous Li-Nb-O films and the synthesis of single-phase LN films with lattice parameters closest to those of stoichiometric single-crystal LN. The most probable mechanisms of irreversible deformation in LN films are: brittle fracture, plastic deformation of crystallites, and grain boundary sliding. LN films synthesized at 650-750°C are most susceptible to brittle fracture. Brittle fracture occurs due to the buildup of macrostresses in the films, resulting from different coefficients of thermal expansion (CTE) of the film and the substrate. The fracture toughness of the films increases significantly when using a substrate with a CTE close to that of the film. The hardness of nano- and microcrystalline LN films is always higher than the hardness of quasi-amorphous Li-Nb-O system films. The decrease in the hardness of а films synthesized at high annealing temperatures is due to a decrease in the concentration of point defects and an increase in the size of the crystallites
- 25 September 2025
- Published by Voronezh State University in Kondensirovannye sredy i mezhfaznye granitsy = Condensed Matter and Interphases
- Vol. 27 (3) , 398-408
Open AccessMechanical Properties of Li-Nb-O System Films
Objective: To quantitatively assess the hardness, elasticity, and plasticity, and to determine the influence of structure and substructure on these parameters in Li-Nb-O system films.Experimental: Li-Nb-O system films with a thickness of ~0.8 μm were grown on non-heated substrates (oxidized single-crystal silicon wafers (SiO₂ layer ~0.4 μm), single-crystal lithium niobate with (0001) orientation) by ion beam sputtering of a lithium niobate target. Thermal annealing of Li-Nb-O films on substrates was performed in air for 10 min (until complete crystallization) at temperatures of 550, 650, 700, 750, 800, and 850 °C. The heterostructures (film/substrate) were cooled with the furnace. The phase composition of the films was investigated by X-ray diffraction (XRD) and selected area electron diffraction (SAED). The substructure was studied by transmission electron microscopy (TEM) and high-resolution TEM (HRTEM, Tecnai G2 30ST) of cross-sectional specimens prepared by ion milling using a Quanta 3D setup. The surface morphology was investigated by scanning electron microscopy (SEM, Teskan Mira) in the topologicalcontrast mode and atomic force microscopy (AFM, Solver47). Mechanical properties – hardness (H) and Young's modulus (E) – were determined from nanoindentation (NI, NanoHardness Tester CSM Instruments) measurements using a Berkovich diamond indenter under the following conditions: maximum load 10 mN, loading rate 10 mN/min, and unloading rate 15 mN/min. Results: It was found that thermal annealing in an oxygen-containing atmosphere at 750°C induces crystallization of quasi-amorphous Li-Nb-O films and the synthesis of single-phase LN films with lattice parameters closest to those of stoichiometric single-crystal LN. The most probable mechanisms of irreversible deformation in LN films are: brittle fracture, plastic deformation of crystallites, and grain boundary sliding. LN films synthesized at 650-750°C are most susceptible to brittle fracture. Brittle fracture occurs due to the buildup of macrostresses in the films, resulting from different coefficients of thermal expansion (CTE) of the film and the substrate. The fracture toughness of the films increases significantly when using a substrate with a CTE close to that of the film. The hardness of nano- and microcrystalline LN films is always higher than the hardness of quasi-amorphous Li-Nb-O system films. The decrease in the hardness of а films synthesized at high annealing temperatures is due to a decrease in the concentration of point defects and an increase in the size of the crystallites
- 23 August 2024
- Published by Elsevier in Thin Solid Films
- Vol. 804
Inelastic relaxation in tin oxide thin films with an amorphous structure
- 23 August 2024
- Published by Elsevier in Thin Solid Films
- Vol. 804
Inelastic relaxation in tin oxide thin films with an amorphous structure