Md Ajwaad Zaman Quashef
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Md Ajwaad Zaman Quashef has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Jukka Viheriälä
Optoelectronics Research Centre, Physics Unit, Tampere University , Korkeakoulunkatu 3, 33720 Tampere
2 shared publications - Mircea Guina
Tampere University
2 shared publications - Nouman Zia
Optoelectronics Research Centre, Physics Unit, Tampere University , Korkeakoulunkatu 3, 33720 Tampere
2 shared publications - Anders E. Wallin
VTT Technical Research Centre of Finland Ltd
1 shared publication - Eero Koivusalo
Optoelectronics Research Centre (ORC), Physics Unit, Tampere University 1 , FI-33720 Tampere
1 shared publication - Joonas Hilska
Tampere University Faculty of Engineering and Natural Sciences
1 shared publication
Latest Publications
- 3 August 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 129 (5)
Low optical loss electrical isolation for multi-section monolithic GaSb-based photonic circuits
Monolithic photonic integrated circuit (PIC) platforms exploiting III–V materials combine passive and active waveguide structures in multi-section optoelectronic device architectures. Their operation requires high electrical isolation between adjacent functional sections without compromising the optical signal. This fundamental requirement is addressed for GaSb-based waveguides, which are known to exhibit high conductivity of p-type layers, reducing the electrical isolation capability. To this end, a co-designed electrical–optical isolation strategy based on using deeply etched strip waveguides combined with adiabatic ridge-to-strip waveguide tapers in GaSb-based multiple-quantum well heterostructures is proposed. While deep etching alone enables isolation resistances of up to 40 kΩ, it severely degrades optical propagation. By introducing optimized adiabatic tapers, we demonstrate good optical performance as single mode continuous-wave lasing in a two-section device with integrated absorber, while maintaining an isolation resistance of 17.3 kΩ; this corresponds to an approximately 17-fold improvement over previously reported GaSb two-section devices. The approach establishes a critical building block for the development of monolithic GaSb-based PICs operating above 2 μm.
- 3 August 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 129 (5)
Low optical loss electrical isolation for multi-section monolithic GaSb-based photonic circuits
Monolithic photonic integrated circuit (PIC) platforms exploiting III–V materials combine passive and active waveguide structures in multi-section optoelectronic device architectures. Their operation requires high electrical isolation between adjacent functional sections without compromising the optical signal. This fundamental requirement is addressed for GaSb-based waveguides, which are known to exhibit high conductivity of p-type layers, reducing the electrical isolation capability. To this end, a co-designed electrical–optical isolation strategy based on using deeply etched strip waveguides combined with adiabatic ridge-to-strip waveguide tapers in GaSb-based multiple-quantum well heterostructures is proposed. While deep etching alone enables isolation resistances of up to 40 kΩ, it severely degrades optical propagation. By introducing optimized adiabatic tapers, we demonstrate good optical performance as single mode continuous-wave lasing in a two-section device with integrated absorber, while maintaining an isolation resistance of 17.3 kΩ; this corresponds to an approximately 17-fold improvement over previously reported GaSb two-section devices. The approach establishes a critical building block for the development of monolithic GaSb-based PICs operating above 2 μm.
- Open Access
- 26 August 2024
- Published by AIP Publishing in Applied Physics Letters
- Vol. 125 (9)
Hybrid integrated GaSb/Si3N4 narrow linewidth (<50 kHz) distributed Bragg reflector laser
A narrow linewidth hybrid integrated distributed Bragg reflector (DBR) laser platform operating at 2 μm wavelength region is demonstrated. The laser architecture comprises AlGaInAsSb/GaSb type-I quantum well reflective semiconductor optical amplifiers butt-coupled to a Si3N4 photonic integrated circuit (PIC), incorporating a narrow-band DBR. The DBR is realized with a long spiral-shaped waveguide structure with periodic circular posts placed adjacent to the waveguide. At room temperature operating conditions, the laser exhibits a maximum continuous wave output power of more than 17 mW for emission near 2 μm. Linewidth properties are analyzed with a heterodyne measurement technique, involving the mixing of the laser signal with a frequency comb phase-locked to an ultra-stable laser. The hybrid laser exhibits a narrow linewidth of ∼8 kHz in 1 ms timescale and ∼50 kHz in 10 ms timescale.
- 26 August 2024
- Published by AIP Publishing in Applied Physics Letters
- Vol. 125 (9)
Open AccessHybrid integrated GaSb/Si3N4 narrow linewidth (<50 kHz) distributed Bragg reflector laser
A narrow linewidth hybrid integrated distributed Bragg reflector (DBR) laser platform operating at 2 μm wavelength region is demonstrated. The laser architecture comprises AlGaInAsSb/GaSb type-I quantum well reflective semiconductor optical amplifiers butt-coupled to a Si3N4 photonic integrated circuit (PIC), incorporating a narrow-band DBR. The DBR is realized with a long spiral-shaped waveguide structure with periodic circular posts placed adjacent to the waveguide. At room temperature operating conditions, the laser exhibits a maximum continuous wave output power of more than 17 mW for emission near 2 μm. Linewidth properties are analyzed with a heterodyne measurement technique, involving the mixing of the laser signal with a frequency comb phase-locked to an ultra-stable laser. The hybrid laser exhibits a narrow linewidth of ∼8 kHz in 1 ms timescale and ∼50 kHz in 10 ms timescale.