Qiyang Xiao
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Qiyang Xiao has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
Qiyang Xiao
2 shared publicationsZhoumo Zeng
2 shared publications- Chang Ma
State Key Laboratory of Precision Measurement Technology and Instrument, Tianjin University, Tianjin 300072, China
1 shared publication Hao Feng
1 shared publication- Hengrui Cui
State Key Laboratory of Precision Measuring Technology and Instruments, Tianjin University, Tianjin, China
1 shared publication - Hui Zhang
Beijing Normal-Hong Kong Baptist University, Zhuhai, China
1 shared publication
Latest Publications
- 1 May 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Measurement of Luders band of cast iron material based on 3D-DIC de-correlation effect
In the material tensile test, the fracture usually starts from generation of the Luders band. The Luders band can be measured by strain, but the conventional strain gauge cannot be used to measure due to undetermined position of the Luders band. The fracture phenomenon can be monitored by the full field strain measurement. However, the common full-field measurement method must cause delay because of the excessive calculation amount. Hence generation of the fracture cannot be measured in real-time. The 3D-DIC method is an efficient way of the full field non-contact measurement. By simplifying the 3D- DIC method and transforming the object of interest, this paper can focus on the generation of large strains, greatly reduce the amount of calculation and monitor the production and development of the Luders band in real time at last.
- 1 May 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Measurement of Luders band of cast iron material based on 3D-DIC de-correlation effect
In the material tensile test, the fracture usually starts from generation of the Luders band. The Luders band can be measured by strain, but the conventional strain gauge cannot be used to measure due to undetermined position of the Luders band. The fracture phenomenon can be monitored by the full field strain measurement. However, the common full-field measurement method must cause delay because of the excessive calculation amount. Hence generation of the fracture cannot be measured in real-time. The 3D-DIC method is an efficient way of the full field non-contact measurement. By simplifying the 3D- DIC method and transforming the object of interest, this paper can focus on the generation of large strains, greatly reduce the amount of calculation and monitor the production and development of the Luders band in real time at last.
- 1 September 2018
- Published by Elsevier in Mechanical Systems and Signal Processing
- Vol. 110, 28-41
A denoising scheme for DSPI phase based on improved variational mode decomposition
- 1 September 2018
- Published by Elsevier in Mechanical Systems and Signal Processing
- Vol. 110, 28-41
A denoising scheme for DSPI phase based on improved variational mode decomposition
- 1 August 2018
- Published by Elsevier in Measurement
- Vol. 124, 163-172
Natural-gas pipeline leak location using variational mode decomposition analysis and cross-time–frequency spectrum
- 1 August 2018
- Published by Elsevier in Measurement
- Vol. 124, 163-172
Natural-gas pipeline leak location using variational mode decomposition analysis and cross-time–frequency spectrum
- 7 March 2018
- Published by IOP Publishing in Measurement Science and Technology
- Vol. 29 (4) , 045203
Adaptive DSPI phase denoising using mutual information and 2D variational mode decomposition
In digital speckle pattern interferometry (DSPI), noise interference leads to a low peak signal-to-noise ratio (PSNR) and measurement errors in the phase map. This paper proposes an adaptive DSPI phase denoising method based on two-dimensional variational mode decomposition (2D-VMD) and mutual information. Firstly, the DSPI phase map is subjected to 2D-VMD in order to obtain a series of band-limited intrinsic mode functions (BLIMFs). Then, on the basis of characteristics of the BLIMFs and in combination with mutual information, a self-adaptive denoising method is proposed to obtain noise-free components containing the primary phase information. The noise-free components are reconstructed to obtain the denoising DSPI phase map. Simulation and experimental results show that the proposed method can effectively reduce noise interference, giving a PSNR that is higher than that of two-dimensional empirical mode decomposition methods.
- 7 March 2018
- Published by IOP Publishing in Measurement Science and Technology
- Vol. 29 (4) , 045203
Adaptive DSPI phase denoising using mutual information and 2D variational mode decomposition
In digital speckle pattern interferometry (DSPI), noise interference leads to a low peak signal-to-noise ratio (PSNR) and measurement errors in the phase map. This paper proposes an adaptive DSPI phase denoising method based on two-dimensional variational mode decomposition (2D-VMD) and mutual information. Firstly, the DSPI phase map is subjected to 2D-VMD in order to obtain a series of band-limited intrinsic mode functions (BLIMFs). Then, on the basis of characteristics of the BLIMFs and in combination with mutual information, a self-adaptive denoising method is proposed to obtain noise-free components containing the primary phase information. The noise-free components are reconstructed to obtain the denoising DSPI phase map. Simulation and experimental results show that the proposed method can effectively reduce noise interference, giving a PSNR that is higher than that of two-dimensional empirical mode decomposition methods.