Yunnen Chen
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Yunnen Chen has a total of 3 co-authors. Here are the top co-authors by number of shared publications:
Jiali Xu
Jiangxi Provincial Key Laboratory of Environmental Pollution Prevention and Control in Mining and Metallurgy, Jiangxi University of Science and Technology, Ganzhou, People’s Republic of China
2 shared publicationsYuting Li
Jiangxi Provincial Key Laboratory of Environmental Pollution Prevention and Control in Mining and Metallurgy, Jiangxi University of Science and Technology, Ganzhou, People’s Republic of China
2 shared publicationsJun Liu
Jiangxi Key Laboratory of Mining & Metallurgy Environmental Pollution Control, Jiangxi University of Science & Technology, Ganzhou, People’s Republic of China
1 shared publication
Latest Publications
- Open Access
- 4 October 2024
- Published by Springer Nature in Scientific Reports
- Vol. 14 (1) , 1-17
Transforming tire-derived char into powerful arsenic adsorbents by mild modification
A large amount of arsenic-containing wastewater discharged by the non-ferrous metal industry will cause serious environmental problems if it is not properly treated. Pyrolysis char of waste tire is a kind of solid waste. Since the surface properties of tire derived char (TC) are affected by tar/ash adhesion during pyrolysis, it is necessary to modify TC to treat wastewater containing As(V) effectively as an adsorbent. At present, most studies on the modification of TC are prepared into activated carbon by high temperature activation in N2 atmosphere. In this study, TC was modified at room temperature and air atmosphere, and Fe(OH)3-TCNaOH adsorbent with particle size of 61–75 μm was obtained under the premise of the removal rate of As(V) and the settling performance of the adsorbent. When the initial concentration of As(V) was 5 mg/L, the removal rate of As(V) by Fe(OH)3-TCNaOH with a particle size of 61–75 μm could reach 90% within 30 min under a wide pH range (3–9). The adsorption of As(V) by Fe(OH)3-TCNaOH was most affected by the coexistence of PO43-, which resulted in the removal rate of As(V) decreased by about 20%. The adsorption mechanism shows that the significant increase in the number of 3–5 nm mesoporous pores of Fe(OH)3-TCNaOH and the formation of H bonds are beneficial to the adsorption of Fe(OH)3-TCNaOH to As(V), and improve the stability of Fe-As complex.
- 4 October 2024
- Published by Springer Nature in Scientific Reports
- Vol. 14 (1) , 1-17
Open AccessTransforming tire-derived char into powerful arsenic adsorbents by mild modification
A large amount of arsenic-containing wastewater discharged by the non-ferrous metal industry will cause serious environmental problems if it is not properly treated. Pyrolysis char of waste tire is a kind of solid waste. Since the surface properties of tire derived char (TC) are affected by tar/ash adhesion during pyrolysis, it is necessary to modify TC to treat wastewater containing As(V) effectively as an adsorbent. At present, most studies on the modification of TC are prepared into activated carbon by high temperature activation in N2 atmosphere. In this study, TC was modified at room temperature and air atmosphere, and Fe(OH)3-TCNaOH adsorbent with particle size of 61–75 μm was obtained under the premise of the removal rate of As(V) and the settling performance of the adsorbent. When the initial concentration of As(V) was 5 mg/L, the removal rate of As(V) by Fe(OH)3-TCNaOH with a particle size of 61–75 μm could reach 90% within 30 min under a wide pH range (3–9). The adsorption of As(V) by Fe(OH)3-TCNaOH was most affected by the coexistence of PO43-, which resulted in the removal rate of As(V) decreased by about 20%. The adsorption mechanism shows that the significant increase in the number of 3–5 nm mesoporous pores of Fe(OH)3-TCNaOH and the formation of H bonds are beneficial to the adsorption of Fe(OH)3-TCNaOH to As(V), and improve the stability of Fe-As complex.
- Open Access
- 2 September 2024
- Published by Springer Nature in Scientific Reports
- Vol. 14 (1) , 1-15
Removal mechanism of phosphorus in water by calcium hydroxide modified copper tailings
With the development of industry and agriculture, eutrophication caused by increasing amounts of phosphorus in the environment has attracted people's attention. On the other hand, copper tailings (CT) is a kind of solid waste with large quantity, large area, and easy to cause groundwater and soil pollution. CT is also a potential resource because of its large specific surface area. CT is intended to be used as an adsorbent for removal phosphate in water, but trace heavy metals and a small amount of phosphate in CT may bring negative effects. Calcium hydroxide (Ca(OH)2) was used to modify CT (CCT), hoping to fix the heavy metals and phosphate in CT at the same time. It was found that the removal capacity of CCT was significantly higher than that of CT. The process of phosphate removal by CCT involves electrostatic sorption and surface precipitation, and there is a synergistic effect between CT and Ca(OH)2. The phosphate removal rate of CCT-0.4 increased with the increase of pH value under alkaline conditions. The XRD patterns of phosphate sorption by CCT mean that Ca3(PO4)2, Ca5(PO4)3(OH) and AlPO4 exist in CCT after phosphate removal, indicating that surface precipitation occurs during the removal process. In summary, the removal mechanism of phosphate by CCT is mainly electrostatic attraction and surface precipitation.
- 2 September 2024
- Published by Springer Nature in Scientific Reports
- Vol. 14 (1) , 1-15
Open AccessRemoval mechanism of phosphorus in water by calcium hydroxide modified copper tailings
With the development of industry and agriculture, eutrophication caused by increasing amounts of phosphorus in the environment has attracted people's attention. On the other hand, copper tailings (CT) is a kind of solid waste with large quantity, large area, and easy to cause groundwater and soil pollution. CT is also a potential resource because of its large specific surface area. CT is intended to be used as an adsorbent for removal phosphate in water, but trace heavy metals and a small amount of phosphate in CT may bring negative effects. Calcium hydroxide (Ca(OH)2) was used to modify CT (CCT), hoping to fix the heavy metals and phosphate in CT at the same time. It was found that the removal capacity of CCT was significantly higher than that of CT. The process of phosphate removal by CCT involves electrostatic sorption and surface precipitation, and there is a synergistic effect between CT and Ca(OH)2. The phosphate removal rate of CCT-0.4 increased with the increase of pH value under alkaline conditions. The XRD patterns of phosphate sorption by CCT mean that Ca3(PO4)2, Ca5(PO4)3(OH) and AlPO4 exist in CCT after phosphate removal, indicating that surface precipitation occurs during the removal process. In summary, the removal mechanism of phosphate by CCT is mainly electrostatic attraction and surface precipitation.