Yitao Zheng
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Yitao Zheng has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
Yun Zhou
Ningbo Helong New Material Co., LTD, Ningbo, 315335, China
3 shared publications- Philip Hall
Department of Chemical and Environmental Engineering, Faculty of Science and Engineering, University of Nottingham, Ningbo, 315100, PR China
2 shared publications - Zheng Wang
Department of Chemical and Environmental Engineering, The University of Nottingham Ningbo China, Ningbo, 315100, China
2 shared publications Bin Wang
1 shared publicationChuang Gao
1 shared publicationFu Gu
Center of Engineering Management, Polytechnic Institute Zhejiang University Hangzhou China
1 shared publication
Latest Publications
- Open Access
- 17 October 2025
- Published by Elsevier in Environmental Research
- Vol. 287, 123147
Life cycle assessment of wood plastic decking manufacturing: Reduction of environmental impacts based on an industrial case study in China
- 17 October 2025
- Published by Elsevier in Environmental Research
- Vol. 287, 123147
Open AccessLife cycle assessment of wood plastic decking manufacturing: Reduction of environmental impacts based on an industrial case study in China
- 15 September 2024
- Published by Wiley in Journal of Vinyl and Additive Technology
- Vol. 31 (1) , 182-198
A comparative study on the mechanical and flammability properties of aluminum hydroxide and hollow glass beads‐filled polypropylene composites
Lightweight polypropylene (PP) composites with high flame retardancy and high thermal stability were required for automobile, electrical and electronic applications. Aluminum hydroxide (Al(OH) 3 ) and two hollow glass beads (HGB) were selected as fillers for polypropylene composite fabrication. The incorporation of 10 wt% HGB (iM30K) into the PP matrix leads to a 3.5% density reduction, and 10 wt% Al(OH) 3 increased the density by 5.4%. The cone calorimeter test (CCT) showed the lowest PHRR of 536.6 kW/m 2 and peak smoke production rate of 0.061 m 2 /s was recorded for 10 wt% HGB (iM30K) loading. The formulation with 10 wt% Al(OH) 3 loading had the lowest flammability; however, the Al(OH) 3 content was not sufficient for a consistent flame‐resistant performance. The incorporation of HGB and Al(OH) 3 resulted in an enhancement of both tensile and flexural modulus; however, it was observed that the tensile, flexural, and impact strengths exhibited a decrement with an increase in the concentration of HGB or Al(OH) 3 . Moreover, the thermogravimetric analysis (TGA) results indicated that at the same filler content, HGB (S60HS) filled PP composites have the highest thermal stability among the prepared composites. Highlights: Effects of HGB and Al(OH) 3 on flame retardancy and thermal stability of PP. Small size HGB (iM30K) exhibited superior smoke suppression performance. Effects of HGB on density reduction of PP based composites. Mechanical properties of HGB or Al(OH) 3 filled PP were investigated. The SEM images revealed the breakage and dispersion of HGB in the composites.
- 15 September 2024
- Published by Wiley in Journal of Vinyl and Additive Technology
- Vol. 31 (1) , 182-198
A comparative study on the mechanical and flammability properties of aluminum hydroxide and hollow glass beads‐filled polypropylene composites
Lightweight polypropylene (PP) composites with high flame retardancy and high thermal stability were required for automobile, electrical and electronic applications. Aluminum hydroxide (Al(OH) 3 ) and two hollow glass beads (HGB) were selected as fillers for polypropylene composite fabrication. The incorporation of 10 wt% HGB (iM30K) into the PP matrix leads to a 3.5% density reduction, and 10 wt% Al(OH) 3 increased the density by 5.4%. The cone calorimeter test (CCT) showed the lowest PHRR of 536.6 kW/m 2 and peak smoke production rate of 0.061 m 2 /s was recorded for 10 wt% HGB (iM30K) loading. The formulation with 10 wt% Al(OH) 3 loading had the lowest flammability; however, the Al(OH) 3 content was not sufficient for a consistent flame‐resistant performance. The incorporation of HGB and Al(OH) 3 resulted in an enhancement of both tensile and flexural modulus; however, it was observed that the tensile, flexural, and impact strengths exhibited a decrement with an increase in the concentration of HGB or Al(OH) 3 . Moreover, the thermogravimetric analysis (TGA) results indicated that at the same filler content, HGB (S60HS) filled PP composites have the highest thermal stability among the prepared composites. Highlights: Effects of HGB and Al(OH) 3 on flame retardancy and thermal stability of PP. Small size HGB (iM30K) exhibited superior smoke suppression performance. Effects of HGB on density reduction of PP based composites. Mechanical properties of HGB or Al(OH) 3 filled PP were investigated. The SEM images revealed the breakage and dispersion of HGB in the composites.
- Open Access
- 31 August 2024
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 32, 4221-4233
Thermal and mechanical behaviour of recycled short milled carbon fibre reinforced polypropylene and recycled polypropylene composites: A comparative study
- 31 August 2024
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 32, 4221-4233
Open AccessThermal and mechanical behaviour of recycled short milled carbon fibre reinforced polypropylene and recycled polypropylene composites: A comparative study