Tomoatsu Ozaki
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Tomoatsu Ozaki has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Hirosuke Sonomura
Osaka Research Institute of Industrial Science and Technology
2 shared publications - Kazuaki Katagiri
Osaka Research Institute of Industrial Science and Technology
2 shared publications - Akitoshi Hayashi
Department of Applied Chemistry, Graduate School of Engineering, Osaka Metropolitan University, 1-1 Gakuen-cho, Naka-ku, Sakai, Osaka, 599-8531, Japan
1 shared publication Gentoku Yoshida
1 shared publicationKeigo Nakano
1 shared publication- Kota Fujiwara
University of Tsukuba
1 shared publication
Latest Publications
- 31 December 2024
- Published by Elsevier in Thin Solid Films
- Vol. 810
Effect of fabrication conditions on Cu film formation on Al2O3 and AlN substrates by friction stirring
- 31 December 2024
- Published by Elsevier in Thin Solid Films
- Vol. 810
Effect of fabrication conditions on Cu film formation on Al2O3 and AlN substrates by friction stirring
- Open Access
- 3 September 2024
- Published by Elsevier in Results in Surfaces and Interfaces
- Vol. 17
Convex structure formation on a Cu substrate by friction stirring using a tool wrapped with Ti foil
- 3 September 2024
- Published by Elsevier in Results in Surfaces and Interfaces
- Vol. 17
Open AccessConvex structure formation on a Cu substrate by friction stirring using a tool wrapped with Ti foil
- Open Access
- 15 October 2021
- Published by Japan Society of Powder and Powder Metallurgy in Journal of the Japan Society of Powder and Powder Metallurgy
- Vol. 68 (10) , 450-456
Effect of Heat Treatment on Mechanical Properties of Al-Cu-TiB2 Alloy Fabricated by Selective Laser Melting
This study examined the microstructures and mechanical properties of Al-Cu-TiB2 alloy fabricated by selective laser melting (SLM). The SLM specimens without solidification cracks were obtained by optimizing laser irradiation conditions, and the relative density was 99.8%. The SLM specimens had a fine solidification structure with equiaxed cells owing to the heterogeneous nucleation by TiB2 particles. The generation of the solidification cracks was thus suppressed due to dispersed shrinkage strain. The hardness of the SLM specimens increased by the solution treatment and subsequent artificial aging treatment. As a result of the precipitation of an Al2Cu phase by aging, the SLM specimens have exhibited excellent strength through precipitation hardening.
- 15 October 2021
- Published by Japan Society of Powder and Powder Metallurgy in Journal of the Japan Society of Powder and Powder Metallurgy
- Vol. 68 (10) , 450-456
Open AccessEffect of Heat Treatment on Mechanical Properties of Al-Cu-TiB2 Alloy Fabricated by Selective Laser Melting
This study examined the microstructures and mechanical properties of Al-Cu-TiB2 alloy fabricated by selective laser melting (SLM). The SLM specimens without solidification cracks were obtained by optimizing laser irradiation conditions, and the relative density was 99.8%. The SLM specimens had a fine solidification structure with equiaxed cells owing to the heterogeneous nucleation by TiB2 particles. The generation of the solidification cracks was thus suppressed due to dispersed shrinkage strain. The hardness of the SLM specimens increased by the solution treatment and subsequent artificial aging treatment. As a result of the precipitation of an Al2Cu phase by aging, the SLM specimens have exhibited excellent strength through precipitation hardening.
- Open Access
- 1 January 2016
- Published by Ceramic Society of Japan in Journal of the Ceramic Society of Japan
- Vol. 124 (3) , 242-246
Improved electrochemical performance of amorphous TiS3 electrodes compared to its crystal for all-solid-state rechargeable lithium batteries
- 1 January 2016
- Published by Ceramic Society of Japan in Journal of the Ceramic Society of Japan
- Vol. 124 (3) , 242-246
Open AccessImproved electrochemical performance of amorphous TiS3 electrodes compared to its crystal for all-solid-state rechargeable lithium batteries