Yu-Chong Tai
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Yu-Chong Tai has a total of 29 co-authors. Here are the top co-authors by number of shared publications:
Dongyang Kang
Electrical Engineering, Caltech, Pasadena, CA 91125, USA
3 shared publications- Wangzhi Dai
Institute of Microelectronics, Peking University, Beijing, 100871, CHINA
2 shared publications Aubrey Shapero
California Institute of Technology, Pasadena, USA
1 shared publication- Azita Emami
Department of Electrical Engineering, California Institute of Technology, Pasadena, CA, USA
1 shared publication - Charles Grosjean
Institut Pasteur, Université Paris Cité, U1224 INSERM, Microenvironment C Immunity Unit, Paris, France
1 shared publication - Chen-Hsuan Lu
Department of Applied Physics and Materials Science, California Institute of Technology, Pasadena, California 91125, United States
1 shared publication
Latest Publications
- Open Access
- 19 August 2024
- Published by Wiley in Advanced Materials Interfaces
- Vol. 11 (27)
Feasibility and Structural Transformation of Electrodeposited Copper Foils for Graphene Synthesis by Plasma‐Enhanced Chemical Vapor Deposition: Implications for High‐Frequency Applications
Large‐area graphene is typically synthesized on rolled‐annealed copper foils, which require transferring to other substrates for applications. This study examines large‐area graphene growth on electrodeposited (ED) copper foils—used in lithium‐ion batteries and printed circuit boards—via plasma‐enhanced chemical vapor deposition (PECVD). It reveals that, for a set plasma power, a minimum growth time ensures full graphene coverage, leading to monolayer and then multilayer graphene, showing PECVD growth on ED copper is not self‐limited. The process also beneficially modifies the ED copper substrate, like removing the surface zinc layer and changing copper grain size and orientation, thus improving graphene growth. Additionally, the study includes high‐frequency scattering parameter (S‐parameter) measurements in a coplanar waveguide (CPW) system. This involves graphene on a sapphire substrate with a silver electrode. The S‐parameter data indicate that the CPW with graphene shows reduced insertion losses in high‐frequency circuits compared to those without graphene. This underscores graphene's role in reducing insertion losses between metallic and dielectric layers in high‐frequency settings, offering valuable insights for industrial and technological applications.
- 19 August 2024
- Published by Wiley in Advanced Materials Interfaces
- Vol. 11 (27)
Open AccessFeasibility and Structural Transformation of Electrodeposited Copper Foils for Graphene Synthesis by Plasma‐Enhanced Chemical Vapor Deposition: Implications for High‐Frequency Applications
Large‐area graphene is typically synthesized on rolled‐annealed copper foils, which require transferring to other substrates for applications. This study examines large‐area graphene growth on electrodeposited (ED) copper foils—used in lithium‐ion batteries and printed circuit boards—via plasma‐enhanced chemical vapor deposition (PECVD). It reveals that, for a set plasma power, a minimum growth time ensures full graphene coverage, leading to monolayer and then multilayer graphene, showing PECVD growth on ED copper is not self‐limited. The process also beneficially modifies the ED copper substrate, like removing the surface zinc layer and changing copper grain size and orientation, thus improving graphene growth. Additionally, the study includes high‐frequency scattering parameter (S‐parameter) measurements in a coplanar waveguide (CPW) system. This involves graphene on a sapphire substrate with a silver electrode. The S‐parameter data indicate that the CPW with graphene shows reduced insertion losses in high‐frequency circuits compared to those without graphene. This underscores graphene's role in reducing insertion losses between metallic and dielectric layers in high‐frequency settings, offering valuable insights for industrial and technological applications.
- Open Access
- 10 October 2018
- Published by Springer Nature in Micro and Nano Systems Letters
- Vol. 6 (1) , 5
Highly controllable and reliable ultra-thin Parylene deposition
- 10 October 2018
- Published by Springer Nature in Micro and Nano Systems Letters
- Vol. 6 (1) , 5
Open AccessHighly controllable and reliable ultra-thin Parylene deposition
- 1 January 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 47-50
Parylene-oil-encapsulated low-drift implantable pressure sensors
This paper demonstrates a parylene-oil-encapsulated packaging technology that applies to commercial pressure sensors to enable intraocular pressure sensing with minimal drift. Commercial digital-output barometers are chosen to be packaged first with 100,000 cSt silicone oil and then sub-micron thick parylene within the volume of the original housing. It is newly found that parylene type and oil viscosity can decide the sign and magnitude of the intrinsic stress in parylene. Additionally, the effect of deposited thickness and temperature on film stress is studied through induced pressure offset. When properly designed, parylene-oil-encapsulated pressure sensors maintain <;0.3% sensitivity drift and <;1 to 2 mmHg offset drift for over 50 to 106+ days in 77 °C saline, equivalent to 25 to 53+ months at 37 °C [1]. This new compact packaging method is promising for converting air-operated commercial sensors to be “implantable” with nearly original sensitivity and minimal offset and drift.
- 1 January 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 47-50
Parylene-oil-encapsulated low-drift implantable pressure sensors
This paper demonstrates a parylene-oil-encapsulated packaging technology that applies to commercial pressure sensors to enable intraocular pressure sensing with minimal drift. Commercial digital-output barometers are chosen to be packaged first with 100,000 cSt silicone oil and then sub-micron thick parylene within the volume of the original housing. It is newly found that parylene type and oil viscosity can decide the sign and magnitude of the intrinsic stress in parylene. Additionally, the effect of deposited thickness and temperature on film stress is studied through induced pressure offset. When properly designed, parylene-oil-encapsulated pressure sensors maintain <;0.3% sensitivity drift and <;1 to 2 mmHg offset drift for over 50 to 106+ days in 77 °C saline, equivalent to 25 to 53+ months at 37 °C [1]. This new compact packaging method is promising for converting air-operated commercial sensors to be “implantable” with nearly original sensitivity and minimal offset and drift.
- 1 January 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 462-464
Reliable deposition of ultra-thin parylene
This paper reports a novel and reliable process to prepare ultra-thin parylene film based on a principle combining both molecular effusion and diffusion. For the first time, a technique for the deposition of parylene film thinner than 20 nm in a highly controllable and repeatable way is developed. Parylene films with various thicknesses could also be prepared in a single deposition run by using this method. This technique holds promising potentials in extensive applications, such as protection/dielectric layer for needle electrodes and flexible electronics, semi-permeable membrane, and other polymer engineering.
- 1 January 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 462-464
Reliable deposition of ultra-thin parylene
This paper reports a novel and reliable process to prepare ultra-thin parylene film based on a principle combining both molecular effusion and diffusion. For the first time, a technique for the deposition of parylene film thinner than 20 nm in a highly controllable and repeatable way is developed. Parylene films with various thicknesses could also be prepared in a single deposition run by using this method. This technique holds promising potentials in extensive applications, such as protection/dielectric layer for needle electrodes and flexible electronics, semi-permeable membrane, and other polymer engineering.
- 1 February 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 01936530,p. 296-297
A fully intraocular 0.0169mm2/pixel 512-channel self-calibrating epiretinal prosthesis in 65nm CMOS
Since their conception and success in human trials, the flexibility and spatial resolution of retinal prostheses have been of major interest. Clinical studies have revealed that hundreds of channels are needed to restore functional visual perception, and more sophisticated waveforms present advantages over biphasic pulses. Initial designs targeted stimulation current levels up to 1mA to ensure functionality. For such designs, an output compliance of >10V was required, and HV technologies were used at the expense of area and power consumption. Human clinical trials have recently shown that implanted electrodes present a stimulus threshold as low as 50μA. In addition, advances in implant technology promise close placement of electrode array and retinal tissue, which can further decrease the required current. Thus, highly scaled LV technologies can provide alternative means to reduce area and power, and to support hundreds of flexible independent channels for fully intraocular implants. In this paper, a self-calibrating 512-channel epiretinal prosthesis in 65nm CMOS is presented. It features dual-band telemetry for power and data, clock recovery, a 2-step calibration technique to match biphasic stimulation currents, and an independent arbitrary output waveform per channel. The implant integrates coils (power and data), IC, external capacitors and electrode array using a biocompatible parylene substrate, providing a fully intraocular solution.
- 1 February 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 01936530,p. 296-297
A fully intraocular 0.0169mm2/pixel 512-channel self-calibrating epiretinal prosthesis in 65nm CMOS
Since their conception and success in human trials, the flexibility and spatial resolution of retinal prostheses have been of major interest. Clinical studies have revealed that hundreds of channels are needed to restore functional visual perception, and more sophisticated waveforms present advantages over biphasic pulses. Initial designs targeted stimulation current levels up to 1mA to ensure functionality. For such designs, an output compliance of >10V was required, and HV technologies were used at the expense of area and power consumption. Human clinical trials have recently shown that implanted electrodes present a stimulus threshold as low as 50μA. In addition, advances in implant technology promise close placement of electrode array and retinal tissue, which can further decrease the required current. Thus, highly scaled LV technologies can provide alternative means to reduce area and power, and to support hundreds of flexible independent channels for fully intraocular implants. In this paper, a self-calibrating 512-channel epiretinal prosthesis in 65nm CMOS is presented. It features dual-band telemetry for power and data, clock recovery, a 2-step calibration technique to match biphasic stimulation currents, and an independent arbitrary output waveform per channel. The implant integrates coils (power and data), IC, external capacitors and electrode array using a biocompatible parylene substrate, providing a fully intraocular solution.
- 1 January 2012
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 10846999,p. 353-356
High yield packaging for high-density multi-channel chip integration on flexible parylene substrate
This paper reports a new chip packaging technique for the assembly of retinal prosthesis device. Here, a photoresist is used as glue to attach a chip to the targeted parylene-C substrate so that 94% of the chip area is used as attachment to prevent delamination. As a validation, chips with 268 connections were used to assess the connection yield. The results show that this new technique, combined with an additional parylene-C coating, provide a high connection yield (>;90%) and is a promising method for high-lead-count implant devices.
- 1 January 2012
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 10846999,p. 353-356
High yield packaging for high-density multi-channel chip integration on flexible parylene substrate
This paper reports a new chip packaging technique for the assembly of retinal prosthesis device. Here, a photoresist is used as glue to attach a chip to the targeted parylene-C substrate so that 94% of the chip area is used as attachment to prevent delamination. As a validation, chips with 268 connections were used to assess the connection yield. The results show that this new technique, combined with an additional parylene-C coating, provide a high connection yield (>;90%) and is a promising method for high-lead-count implant devices.
- Open Access
- 7 November 2002
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 10846999,p. 541-546
Mass flowmeter using a multi-sensor chip
We report here a novel mass flowmeter using a multisensor chip that includes a 1-D array of pressure, temperature and shear stress sensors. This shear stress sensor based flowmeter is capable of high sensitivity and wide measurement range. Our study also shows that the mass flowmeter using shear-stress sensors produces better resolution than that from pressure sensors in the laminar flow regime. Extensive tests have been carried out to evaluate the effects of overheat ratio, channel height and gas properties. We also find the V/sup 2//spl prop//spl tau//sup 1/3/ law for conventional hot film sensors does not hold for our micromachined shear stress sensor.
- 7 November 2002
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 10846999,p. 541-546
Open AccessMass flowmeter using a multi-sensor chip
We report here a novel mass flowmeter using a multisensor chip that includes a 1-D array of pressure, temperature and shear stress sensors. This shear stress sensor based flowmeter is capable of high sensitivity and wide measurement range. Our study also shows that the mass flowmeter using shear-stress sensors produces better resolution than that from pressure sensors in the laminar flow regime. Extensive tests have been carried out to evaluate the effects of overheat ratio, channel height and gas properties. We also find the V/sup 2//spl prop//spl tau//sup 1/3/ law for conventional hot film sensors does not hold for our micromachined shear stress sensor.
- Open Access
- 1 January 1999
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 10846999,p. 147-152
A practical thermopneumatic valve
Previously, we reported a thermopneumatic silicone rubber membrane valve [1997]. This valve combined thermopneumatic actuation with a low modulus silicone rubber membrane. However, the leakage of the working fluid through the membrane rendered the valve unusable in a day or two. Here, we present extensive optimization and characterization of a redesigned valve structure. This new design has a suspended membrane heater optimized for low power consumption, a composite silicone rubber on Parylene membrane that exhibits low permeability and modulus, and a novel valve seat designed to improve sealing in the presence of particles. The valve has been extensively characterized with respect to power consumption vs. flow rate and transient response. Very low power consumption has been demonstrated. For example, less than 40 mW is required to switch a one slpm nitrogen flow at 33 psi. Water requires close to 100 mW due to the cooling effect of the liquid. The previously reported valve required more than 280 mW to switch a similar air flow.
- 1 January 1999
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 10846999,p. 147-152
Open AccessA practical thermopneumatic valve
Previously, we reported a thermopneumatic silicone rubber membrane valve [1997]. This valve combined thermopneumatic actuation with a low modulus silicone rubber membrane. However, the leakage of the working fluid through the membrane rendered the valve unusable in a day or two. Here, we present extensive optimization and characterization of a redesigned valve structure. This new design has a suspended membrane heater optimized for low power consumption, a composite silicone rubber on Parylene membrane that exhibits low permeability and modulus, and a novel valve seat designed to improve sealing in the presence of particles. The valve has been extensively characterized with respect to power consumption vs. flow rate and transient response. Very low power consumption has been demonstrated. For example, less than 40 mW is required to switch a one slpm nitrogen flow at 33 psi. Water requires close to 100 mW due to the cooling effect of the liquid. The previously reported valve required more than 280 mW to switch a similar air flow.