Jinxiang Fang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Jinxiang Fang has a total of 70 co-authors. Here are the top co-authors by number of shared publications:
Haotian He
Faculty of Mechanical and Electrical Engineering, Kunming University of Science and Technology, Kunming, People’s Republic of China
10 shared publicationsTong Sun
Faculty of Mechanical and Electrical Engineering, Kunming University of Science and Technology, Kunming, People’s Republic of China
6 shared publicationsH.T. He
5 shared publicationsHaojie Jin
Kunming University of Science and Technology
5 shared publicationsJingtao Wei
Kunming University of Science and Technology
5 shared publicationsTingting Guo
5 shared publications
Latest Publications
- 17 October 2026
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 979
Microstructure and properties of Nb94Mo4.5Hf0.75C0.75 produced via selective electron beam melting
- 17 October 2026
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 979
Microstructure and properties of Nb94Mo4.5Hf0.75C0.75 produced via selective electron beam melting
- Open Access
- 17 September 2026
- Published by Elsevier in SSRN Electronic Journal
Build direction heterogeneity in microstructure, mechanical and corrosion resistance of additive friction stir deposited AZ31B magnesium alloy
Additive friction stir deposition (AFSD) is a solid-state additive manufacturing route capable of producing fully dense magnesium alloy components. A 16-layer AZ31B deposit was fabricated by AFSD, and its top, middle and bottom regions were compared with the rolled base material (BM) in grain structure, texture, geometrically necessary dislocation (GND) density, microhardness, tensile properties and corrosion behavior. The deposit was macroscopically dense, with coarser equiaxed grains whose mean size increased from 18.98 µm at the top to 27.21 µm at the bottom, compared with 11.18 µm for the BM. These results reveal a pronounced build-direction heterogeneity in the microstructure, texture, mechanical behavior and corrosion resistance of the deposit. The basal-type texture intensified toward the bottom, and the middle layer showed the highest GND density. Its hardness was slightly lower but ultimate tensile strength higher than the BM, with a much lower yield strength and pronounced LD–TD anisotropy associated with the texture-dependent activation of basal and prismatic slip. TEM revealed coarser, more heterogeneously distributed Al–Mn precipitates in the deposit than in the BM, which may enhance local micro-galvanic coupling. In 3.5 wt.% NaCl solution, the corrosion resistance decreased in the order BM > top > middle > bottom, and the corrosion rate increased by about 17 times, from 0.263 mm·y-1 for the BM to 4.59 mm·y-1 for the bottom layer, consistent with the coarser grains toward the bottom.
- 17 September 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessBuild direction heterogeneity in microstructure, mechanical and corrosion resistance of additive friction stir deposited AZ31B magnesium alloy
Additive friction stir deposition (AFSD) is a solid-state additive manufacturing route capable of producing fully dense magnesium alloy components. A 16-layer AZ31B deposit was fabricated by AFSD, and its top, middle and bottom regions were compared with the rolled base material (BM) in grain structure, texture, geometrically necessary dislocation (GND) density, microhardness, tensile properties and corrosion behavior. The deposit was macroscopically dense, with coarser equiaxed grains whose mean size increased from 18.98 µm at the top to 27.21 µm at the bottom, compared with 11.18 µm for the BM. These results reveal a pronounced build-direction heterogeneity in the microstructure, texture, mechanical behavior and corrosion resistance of the deposit. The basal-type texture intensified toward the bottom, and the middle layer showed the highest GND density. Its hardness was slightly lower but ultimate tensile strength higher than the BM, with a much lower yield strength and pronounced LD–TD anisotropy associated with the texture-dependent activation of basal and prismatic slip. TEM revealed coarser, more heterogeneously distributed Al–Mn precipitates in the deposit than in the BM, which may enhance local micro-galvanic coupling. In 3.5 wt.% NaCl solution, the corrosion resistance decreased in the order BM > top > middle > bottom, and the corrosion rate increased by about 17 times, from 0.263 mm·y-1 for the BM to 4.59 mm·y-1 for the bottom layer, consistent with the coarser grains toward the bottom.
- Open Access
- 12 September 2026
- Published by Elsevier in SSRN Electronic Journal
Build direction heterogeneity in microstructure, mechanical and corrosion resistance of additive friction stir deposited AZ31B magnesium alloy
Additive friction stir deposition (AFSD) is a solid-state additive manufacturing route capable of producing fully dense magnesium alloy components. A 16-layer AZ31B deposit was fabricated by AFSD, and its top, middle and bottom regions were compared with the rolled base material (BM) in grain structure, texture, geometrically necessary dislocation (GND) density, microhardness, tensile properties and corrosion behavior. The deposit was macroscopically dense, with coarser equiaxed grains whose mean size increased from 18.98 µm at the top to 27.21 µm at the bottom, compared with 11.18 µm for the BM. These results reveal a pronounced build-direction heterogeneity in the microstructure, texture, mechanical behavior and corrosion resistance of the deposit. The basal-type texture intensified toward the bottom, and the middle layer showed the highest GND density. Its hardness was slightly lower but ultimate tensile strength higher than the BM, with a much lower yield strength and pronounced LD–TD anisotropy associated with the texture-dependent activation of basal and prismatic slip. TEM revealed coarser, more heterogeneously distributed Al–Mn precipitates in the deposit than in the BM, which may enhance local micro-galvanic coupling. In 3.5 wt.% NaCl solution, the corrosion resistance decreased in the order BM > top > middle > bottom, and the corrosion rate increased by about 17 times, from 0.263 mm·y-1 for the BM to 4.59 mm·y-1 for the bottom layer, consistent with the coarser grains toward the bottom.
- 12 September 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessBuild direction heterogeneity in microstructure, mechanical and corrosion resistance of additive friction stir deposited AZ31B magnesium alloy
Additive friction stir deposition (AFSD) is a solid-state additive manufacturing route capable of producing fully dense magnesium alloy components. A 16-layer AZ31B deposit was fabricated by AFSD, and its top, middle and bottom regions were compared with the rolled base material (BM) in grain structure, texture, geometrically necessary dislocation (GND) density, microhardness, tensile properties and corrosion behavior. The deposit was macroscopically dense, with coarser equiaxed grains whose mean size increased from 18.98 µm at the top to 27.21 µm at the bottom, compared with 11.18 µm for the BM. These results reveal a pronounced build-direction heterogeneity in the microstructure, texture, mechanical behavior and corrosion resistance of the deposit. The basal-type texture intensified toward the bottom, and the middle layer showed the highest GND density. Its hardness was slightly lower but ultimate tensile strength higher than the BM, with a much lower yield strength and pronounced LD–TD anisotropy associated with the texture-dependent activation of basal and prismatic slip. TEM revealed coarser, more heterogeneously distributed Al–Mn precipitates in the deposit than in the BM, which may enhance local micro-galvanic coupling. In 3.5 wt.% NaCl solution, the corrosion resistance decreased in the order BM > top > middle > bottom, and the corrosion rate increased by about 17 times, from 0.263 mm·y-1 for the BM to 4.59 mm·y-1 for the bottom layer, consistent with the coarser grains toward the bottom.
- Open Access
- 9 September 2026
- Published by IOP Publishing in Physica Scripta
- Vol. 101 (36) , 365510
Simulation and experimental investigation of a graphene resistive film/quartz glass-based high-temperature metamaterial absorber
Round coins with square holes were widely used across many dynasties in ancient China because their highly symmetric geometry and simple structure facilitated mass production. For metamaterial absorbers (MAs), geometric symmetry is beneficial for achieving polarization-insensitive responses and contributes to angular stability, whereas structural simplicity facilitates fabrication. Inspired by these characteristics, a high-temperature MA featuring an ancient coin-shaped resistive-film resonator was proposed. With increasing temperature, variations in the geometry and material parameters of the absorber may affect its electromagnetic absorption performance. To maintain stable absorption over a wide temperature range, the sheet resistance of the resistive film was optimized to reduce the overall temperature dependence of the absorber. The proposed MA comprises three layers: an ancient coin-shaped graphene resistive film as the top layer, a quartz glass dielectric substrate as the intermediate layer, and a copper ground plane as the bottom layer. Experimental results showed that the fabricated absorber maintained stable absorption performance from room temperature to 400 °C. At 400 °C, its reflection coefficient remained below −10 dB over the frequency range of 7.18–11.96 GHz, corresponding to an absorptivity above 90%. The proposed high-temperature MA combines good absorption performance, a simple structure, and low fabrication complexity, offering a practical approach to the development of high-performance MAs for high-temperature applications.
- 9 September 2026
- Published by IOP Publishing in Physica Scripta
- Vol. 101 (36) , 365510
Open AccessSimulation and experimental investigation of a graphene resistive film/quartz glass-based high-temperature metamaterial absorber
Round coins with square holes were widely used across many dynasties in ancient China because their highly symmetric geometry and simple structure facilitated mass production. For metamaterial absorbers (MAs), geometric symmetry is beneficial for achieving polarization-insensitive responses and contributes to angular stability, whereas structural simplicity facilitates fabrication. Inspired by these characteristics, a high-temperature MA featuring an ancient coin-shaped resistive-film resonator was proposed. With increasing temperature, variations in the geometry and material parameters of the absorber may affect its electromagnetic absorption performance. To maintain stable absorption over a wide temperature range, the sheet resistance of the resistive film was optimized to reduce the overall temperature dependence of the absorber. The proposed MA comprises three layers: an ancient coin-shaped graphene resistive film as the top layer, a quartz glass dielectric substrate as the intermediate layer, and a copper ground plane as the bottom layer. Experimental results showed that the fabricated absorber maintained stable absorption performance from room temperature to 400 °C. At 400 °C, its reflection coefficient remained below −10 dB over the frequency range of 7.18–11.96 GHz, corresponding to an absorptivity above 90%. The proposed high-temperature MA combines good absorption performance, a simple structure, and low fabrication complexity, offering a practical approach to the development of high-performance MAs for high-temperature applications.
- 8 July 2026
- Published by Springer Nature in JOM
- Vol. 78 (12) , 11188-11200
Effects of TiAl Addition on the Microstructure and Mechanical Properties of Laser-Deposited CoCrNi Medium-Entropy Alloy
- 8 July 2026
- Published by Springer Nature in JOM
- Vol. 78 (12) , 11188-11200
Effects of TiAl Addition on the Microstructure and Mechanical Properties of Laser-Deposited CoCrNi Medium-Entropy Alloy
- 4 March 2026
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 959
Effects of Hf and Re on the microstructure and mechanical properties of Nb1.6Mo0.3C0.04 alloy
- 4 March 2026
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 959
Effects of Hf and Re on the microstructure and mechanical properties of Nb1.6Mo0.3C0.04 alloy
- 14 January 2026
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 1053
The effect of Zr, Ti, and Hf on the microstructure and mechanical properties of the Nb1.6Mo0.3C0.04 refractory alloy
- 14 January 2026
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 1053
The effect of Zr, Ti, and Hf on the microstructure and mechanical properties of the Nb1.6Mo0.3C0.04 refractory alloy