Ivana Jevtić
Research Subjects
Ivana Jevtić has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Aleksa Milovanović
Faculty of Mechanical Engineering, University of Belgrade - Innovation Center, Belgrade, Serbia
3 shared publications - Miloš Milošević
Innovation Center of the Faculty of Mechanical Engineering, Belgrade, Serbia
3 shared publications - Aleksandar Sedmak
University of Belgrade, Faculty of Mechanical Engineering, Belgrade, Serbia
2 shared publications - Goran Mladenović
University of Belgrade
2 shared publications - Isaak Trajković
Innovation Center of the Faculty of Mechanical Engineering, Belgrade, Serbia
2 shared publications - Božica Bojović
Faculty of Mechanical Engineering, University of Belgrade, 11120 Belgrade, Serbia
1 shared publication
Latest Publications
- 30 November 2025
- Published by Society for Structural Integrity and Life "Prof. dr Stojan Sedmak" in Structural Integrity and Life
- Vol. 25 (2) , 227-235
Impact properties of FDM-grade PLA polymer relative to infill density
This research paper focuses on the influence of infill density on the impact properties of FDM-grade PLA material, i.e., how impact properties degrade with lower infill percentages. Most FDM machines' infill density can vary between 10 % and 100 %. Here, we include the full infill density spectrum with an increment of 10 % (10 specimen groups). The authors’ previous research findings show the benefits of smaller layer heights regarding repeatability of results and impact strength values. Thus, the employed layer thickness here is 0.1 mm, the lowest resolution for most FDM machines. Tests were conducted at room temperature and a controlled humidity level of around 50 % on the Charpy instrumented pendulum.
- 30 November 2025
- Published by Society for Structural Integrity and Life "Prof. dr Stojan Sedmak" in Structural Integrity and Life
- Vol. 25 (2) , 227-235
Impact properties of FDM-grade PLA polymer relative to infill density
This research paper focuses on the influence of infill density on the impact properties of FDM-grade PLA material, i.e., how impact properties degrade with lower infill percentages. Most FDM machines' infill density can vary between 10 % and 100 %. Here, we include the full infill density spectrum with an increment of 10 % (10 specimen groups). The authors’ previous research findings show the benefits of smaller layer heights regarding repeatability of results and impact strength values. Thus, the employed layer thickness here is 0.1 mm, the lowest resolution for most FDM machines. Tests were conducted at room temperature and a controlled humidity level of around 50 % on the Charpy instrumented pendulum.
- 15 May 2024
- Published by Society for Structural Integrity and Life "Prof. dr Stojan Sedmak" in Structural Integrity and Life
- Vol. 24 (1) , 3-7
Printing orientation and place influencing the com¬pressive strength of polyamid 12 specimens obtained by SLS technology
This research aims to determine how the orientation and placement of printing impacts the compressive strength of specimens manufactured by Selective Laser Sintering (SLS). The research includes compressive specimens in which the CAD model dimensions are selected according to the ISO 604 standard, and specimen geometry Ø10x20 mm in bulk. All specimen configurations are additively manufactured in two different printing orientations, horizontal and vertical, and printed in the middle and on the edge of the powder bed. All specimens are additively manufactured using Polyamide 12 (PA 12) material on a Fuse 1 device (FormLabs, located in Summerville, MA). Compressive strength testing was carried out using a Shimadzu AGS-X universal testing machine (Shimadzu Corp., Kyoto, Japan).
- 15 May 2024
- Published by Society for Structural Integrity and Life "Prof. dr Stojan Sedmak" in Structural Integrity and Life
- Vol. 24 (1) , 3-7
Printing orientation and place influencing the com¬pressive strength of polyamid 12 specimens obtained by SLS technology
This research aims to determine how the orientation and placement of printing impacts the compressive strength of specimens manufactured by Selective Laser Sintering (SLS). The research includes compressive specimens in which the CAD model dimensions are selected according to the ISO 604 standard, and specimen geometry Ø10x20 mm in bulk. All specimen configurations are additively manufactured in two different printing orientations, horizontal and vertical, and printed in the middle and on the edge of the powder bed. All specimens are additively manufactured using Polyamide 12 (PA 12) material on a Fuse 1 device (FormLabs, located in Summerville, MA). Compressive strength testing was carried out using a Shimadzu AGS-X universal testing machine (Shimadzu Corp., Kyoto, Japan).
- 10 May 2024
- Published by Faculty of Technical Sciences in Advanced Technologies & Materials
- Vol. 49 (1) , 33-37
Mechanical Properties Variation Due To Building Orientation of ABS Resin Material
Considering that additive manufacturing technology, has evolved significantly over the past few decades, understanding of materials mechanical properties became important part of researches with the goal of further improvement of production Among the seven different AM technologies, in this research is used digital light processing (DLP) 3D printing process with LCD projector. The thermoplastic polymer material acrylonitrile butadiene styrene (ABS) is a widely used material for 3D plastics printing, and in this study, it is chosen in the resin form. So far, this type of material has not been sufficiently studied, and the aim of this study was to determine the mechanical properties for two different specimens’ building orientations (45° and 90°). Specimen’s geometry is chosen according to the respective standards for mechanical testing’s. Because of the difficulties and warping which occur when printing the flat, thin and long specimens, orientation ‘on edge’, i.e., 90° is chosen, as well as the 45° orientation, for comparison. Tensile, three point bending and compression mechanical tests were performed and Matlab is used to create stress-strain curves. Additionally, microscopy is performed for more comprehensive insight of the behaviour of the ABS resin printed via DLP-LCD technology. Comparison of mechanical properties for two orientations leads to the overview of printing parameters which result in better mechanical properties regard to specific application. Better behaviour and compression mechanical properties are noticed in 90° orientation printed ABS resin specimens, compared to 45° ones, while flexure behaviour of ABS is the same regardless to building orientation.
- 10 May 2024
- Published by Faculty of Technical Sciences in Advanced Technologies & Materials
- Vol. 49 (1) , 33-37
Mechanical Properties Variation Due To Building Orientation of ABS Resin Material
Considering that additive manufacturing technology, has evolved significantly over the past few decades, understanding of materials mechanical properties became important part of researches with the goal of further improvement of production Among the seven different AM technologies, in this research is used digital light processing (DLP) 3D printing process with LCD projector. The thermoplastic polymer material acrylonitrile butadiene styrene (ABS) is a widely used material for 3D plastics printing, and in this study, it is chosen in the resin form. So far, this type of material has not been sufficiently studied, and the aim of this study was to determine the mechanical properties for two different specimens’ building orientations (45° and 90°). Specimen’s geometry is chosen according to the respective standards for mechanical testing’s. Because of the difficulties and warping which occur when printing the flat, thin and long specimens, orientation ‘on edge’, i.e., 90° is chosen, as well as the 45° orientation, for comparison. Tensile, three point bending and compression mechanical tests were performed and Matlab is used to create stress-strain curves. Additionally, microscopy is performed for more comprehensive insight of the behaviour of the ABS resin printed via DLP-LCD technology. Comparison of mechanical properties for two orientations leads to the overview of printing parameters which result in better mechanical properties regard to specific application. Better behaviour and compression mechanical properties are noticed in 90° orientation printed ABS resin specimens, compared to 45° ones, while flexure behaviour of ABS is the same regardless to building orientation.
- Open Access
- 1 January 2024
- Published by National Library of Serbia in Science of Sintering
- Vol. 56 (1) , 45-57
The influence of printing orientation on the flexural strength of PA 12 specimens produced by SLS
This article aims to investigate the mechanical characteristics of specimens fabricated using Selective Laser Sintering technology. The research covers flexural specimens, produced by PA12 materials. CAD model dimensions were selected according to the ISO 178 standard, and the chosen specimen geometry is 96 x 8 x 4 [mm] in bulk. All specimens were produced using a specialized machine Fuse 1 (FormLabs, Summerville, MA). Four specimen batches were produced, each with a different printing orientation (i.e. vertical and horizontal) and location on the printing plate (i.e. in the middle and on the edge of the powder bed). The specimens are tested using a Shimadzu universal machine for testing the mechanical characteristics of materials, AGS-X 100 kN, with a unique additional tool for testing 3-point bending specimens.
- 1 January 2024
- Published by National Library of Serbia in Science of Sintering
- Vol. 56 (1) , 45-57
Open AccessThe influence of printing orientation on the flexural strength of PA 12 specimens produced by SLS
This article aims to investigate the mechanical characteristics of specimens fabricated using Selective Laser Sintering technology. The research covers flexural specimens, produced by PA12 materials. CAD model dimensions were selected according to the ISO 178 standard, and the chosen specimen geometry is 96 x 8 x 4 [mm] in bulk. All specimens were produced using a specialized machine Fuse 1 (FormLabs, Summerville, MA). Four specimen batches were produced, each with a different printing orientation (i.e. vertical and horizontal) and location on the printing plate (i.e. in the middle and on the edge of the powder bed). The specimens are tested using a Shimadzu universal machine for testing the mechanical characteristics of materials, AGS-X 100 kN, with a unique additional tool for testing 3-point bending specimens.