Milada Novaković
Research Subjects
Milada Novaković has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- Anita Milosavljevic
Technical Faculty “Mihajlo Pupin”, University of Novi Sad, 21000 Novi Sad, Serbia
3 shared publications - Dragan Djordjic
Institute of General and Physical Chemistry, Belgrade, Republic of Serbia
3 shared publications - Vasilije Petrovic
Technical Faculty “Mihajlo Pupin”, University of Novi Sad, 21000 Novi Sad, Serbia
3 shared publications Belgrade Ministry Of Economy
1 shared publication- Danka Đurđić
Technical Faculty “Mihajlo Pupin”, University of Novi Sad, 23000 Zrenjanin, Serbia
1 shared publication - Darko Radovancevic
University of Novi Sad, Technical Faculty “Mihajlo Pupin,” 2
1 shared publication
Latest Publications
- Open Access
- 1 January 2026
- Published by Centre for Evaluation in Education and Science (CEON/CEES)
- No. Part four,p. 436-443
Sustainable textile waste management as an engineering response to environmental protection challenges
The textile sector is a significant source of environmental pressure due to high consumption of raw materials, water, and energy, as well as growing amounts of waste generated during the production, use, and disposal of textile products. This paper analyzes sustainable textile waste management as an engineering response to environmental protection challenges. Based on a review of relevant literature, the paper considers environmental pressures related to textile consumption, textile waste flows, key waste management approaches, and modern technological solutions for sorting and recycling. Special attention is given to automated sorting based on NIR spectroscopy and sensor-robotic systems, as well as to the role of eco-design and circular models in improving recyclability and material flow closure. The analysis indicates that sustainable textile waste management requires coordinated application of collection, sorting, recycling, and product design strategies.
- 1 January 2026
- Published by Centre for Evaluation in Education and Science (CEON/CEES)
- No. Part four,p. 436-443
Open AccessSustainable textile waste management as an engineering response to environmental protection challenges
The textile sector is a significant source of environmental pressure due to high consumption of raw materials, water, and energy, as well as growing amounts of waste generated during the production, use, and disposal of textile products. This paper analyzes sustainable textile waste management as an engineering response to environmental protection challenges. Based on a review of relevant literature, the paper considers environmental pressures related to textile consumption, textile waste flows, key waste management approaches, and modern technological solutions for sorting and recycling. Special attention is given to automated sorting based on NIR spectroscopy and sensor-robotic systems, as well as to the role of eco-design and circular models in improving recyclability and material flow closure. The analysis indicates that sustainable textile waste management requires coordinated application of collection, sorting, recycling, and product design strategies.
- Open Access
- 30 May 2025
- Published by SAGE Publications in AATCC Journal of Research
- Vol. 12 (3)
Influence of Stitch Density on Seam Strength in Cotton Fabrics
The goal of this paper was to investigate the influence of three different fabric thread densities per weft (10, 17, and 25 cm −1 ) as well as three different linear densities of weft threads (20, 30, and 50 Tex) on the seam strength of cotton fabrics. When measuring seam strength, the values of the F – ε curve were monitored. In this, a uniform increase in force is observed in all samples up to a certain point. After that point, the force suddenly begins to decrease for a while. Then, the same force begins to increase again. That part of the curve at the point where the force begins to decrease is defined in this paper as seam yielding. Therefore, it is concluded that the seam at this point is significantly damaged in structure. The results obtained show that the values of seam strength, for all samples, increase with increasing: stitch density, weft thread density, and weft linear density. It is concluded that the average yield force in samples B decreases by 21.54% and by 32.94% in samples C, compared to the average yield force values of samples A. The average yield force in samples E decreases by 23.24% and that in samples F decreases by 37.92% compared to the average yield force values of samples D. The average yield force in samples H decreases by 19.87% and in samples I it decreases by 24.92% compared to the average yield force values of samples G. The results obtained show that weft yarns with a larger cross-section more intensively resist thread yielding in the seam. Defining these parameters represents a significant contribution for manufacturers of quality clothing because it is possible to project in advance the intensities of forces to which seams in clothing can be subjected to without impairing their quality.
- 30 May 2025
- Published by SAGE Publications in AATCC Journal of Research
- Vol. 12 (3)
Open AccessInfluence of Stitch Density on Seam Strength in Cotton Fabrics
The goal of this paper was to investigate the influence of three different fabric thread densities per weft (10, 17, and 25 cm −1 ) as well as three different linear densities of weft threads (20, 30, and 50 Tex) on the seam strength of cotton fabrics. When measuring seam strength, the values of the F – ε curve were monitored. In this, a uniform increase in force is observed in all samples up to a certain point. After that point, the force suddenly begins to decrease for a while. Then, the same force begins to increase again. That part of the curve at the point where the force begins to decrease is defined in this paper as seam yielding. Therefore, it is concluded that the seam at this point is significantly damaged in structure. The results obtained show that the values of seam strength, for all samples, increase with increasing: stitch density, weft thread density, and weft linear density. It is concluded that the average yield force in samples B decreases by 21.54% and by 32.94% in samples C, compared to the average yield force values of samples A. The average yield force in samples E decreases by 23.24% and that in samples F decreases by 37.92% compared to the average yield force values of samples D. The average yield force in samples H decreases by 19.87% and in samples I it decreases by 24.92% compared to the average yield force values of samples G. The results obtained show that weft yarns with a larger cross-section more intensively resist thread yielding in the seam. Defining these parameters represents a significant contribution for manufacturers of quality clothing because it is possible to project in advance the intensities of forces to which seams in clothing can be subjected to without impairing their quality.
- Open Access
- 1 January 2025
- Published by National Library of Serbia in Science of Sintering
- Vol. 58 (00) , 5
Analysis of the qualitative characteristics of polo shirts made of cotton and cotton/elastane single pike weave before, during and after 60 washing cycles with commercial detergents
The qualitative characteristics of T-shirts made of 100% cotton and 95% cotton and 5% elastane were investigated before and after 20, 40 and 60 cycles of washing with commercial detergents. The results of the experimental tests were approximated by a nonlinear model of data fitting, which is in the form of a 9th degree polynomial. This defines the deformation characteristics, which can be used to predict the changes that occur within the structure of the knitwear during stress. The results obtained make it possible to pre-design the intensities of forces to which polo shirts can be subjected without compromising their quality. The results also state that T-shirts with elastane have 12% higher values of bursting strength and higher values of forces at the limit of elasticity compared to pure cotton T-shirts. Cotton T-shirts have 21% higher air permeability and 10% higher water vapor permeability. Cotton T-shirts with elastane have a higher surface mass and stitch density per cm-2 compared to pure cotton T-shirts. Paper show the qualitative changes of polo shirts during the six-month maintenance cycle and their deformation characteristics. These findings offer valuable insights into the longevity of polo shirts, potentially guiding manufacturers in designing more durable work uniforms.
- 1 January 2025
- Published by National Library of Serbia in Science of Sintering
- Vol. 58 (00) , 5
Open AccessAnalysis of the qualitative characteristics of polo shirts made of cotton and cotton/elastane single pike weave before, during and after 60 washing cycles with commercial detergents
The qualitative characteristics of T-shirts made of 100% cotton and 95% cotton and 5% elastane were investigated before and after 20, 40 and 60 cycles of washing with commercial detergents. The results of the experimental tests were approximated by a nonlinear model of data fitting, which is in the form of a 9th degree polynomial. This defines the deformation characteristics, which can be used to predict the changes that occur within the structure of the knitwear during stress. The results obtained make it possible to pre-design the intensities of forces to which polo shirts can be subjected without compromising their quality. The results also state that T-shirts with elastane have 12% higher values of bursting strength and higher values of forces at the limit of elasticity compared to pure cotton T-shirts. Cotton T-shirts have 21% higher air permeability and 10% higher water vapor permeability. Cotton T-shirts with elastane have a higher surface mass and stitch density per cm-2 compared to pure cotton T-shirts. Paper show the qualitative changes of polo shirts during the six-month maintenance cycle and their deformation characteristics. These findings offer valuable insights into the longevity of polo shirts, potentially guiding manufacturers in designing more durable work uniforms.
- Open Access
- 1 January 2025
- Published by Centre for Evaluation in Education and Science (CEON/CEES)
- No. Part three,p. 229-234
Radon level studies and climate change
Radon is a radioactive gas, not detectable by human senses as it is without smell, taste and color. It can leave the ground and enter into dwellings, ocasionally also in larger concentrations when presenting real threat to human health as the lung cancer can be also one of the consequences of its regular breathing in. Regular radon level controls are important in both living and working environment. Some global radon level studies show that climate changes can negatively influence radon level in houses, leading to its increased values. We monitored for few years radon concentrations at Technical College of Applied Sciences in Zrenjanin and at Technical Faculty "Mihajlo Pupin" in Zrenjanin in order to control radon concentration level.
- 1 January 2025
- Published by Centre for Evaluation in Education and Science (CEON/CEES)
- No. Part three,p. 229-234
Open AccessRadon level studies and climate change
Radon is a radioactive gas, not detectable by human senses as it is without smell, taste and color. It can leave the ground and enter into dwellings, ocasionally also in larger concentrations when presenting real threat to human health as the lung cancer can be also one of the consequences of its regular breathing in. Regular radon level controls are important in both living and working environment. Some global radon level studies show that climate changes can negatively influence radon level in houses, leading to its increased values. We monitored for few years radon concentrations at Technical College of Applied Sciences in Zrenjanin and at Technical Faculty "Mihajlo Pupin" in Zrenjanin in order to control radon concentration level.
- 1 January 2024
- Published by University Library in Kragujevac
- p. 38-44
ARTIFICIAL INTELLIGENCE IN FUNCTION OF IMPROVING PRODUCT FUNCTIONALITIES
The paper aims to present the author’s vision about the possibility of applying artificial intelligence in improving the functionality of products/services from series to series by monitoring the functionality of users, on the market and in all other environments where elements for the analysis of the improvement of individual product functionalities can be found. The paper gives a clear position on the constituent elements that should make up such a functional model with all the associated elements and connections with external entities, as well as a description of the product/service improvement cycle using artificial intelligence. Artificial intelligence is not a supporting part of the model, but used as a support for deciding whether and to what extent certain proposed existing functionality will be improved or new functionality will be added to the product/service. Artificial intelligence certainly opens a new stage of the industrial revolution because it’s a big step forward in production with its technological capacity.
- 1 January 2024
- Published by University Library in Kragujevac
- p. 38-44
ARTIFICIAL INTELLIGENCE IN FUNCTION OF IMPROVING PRODUCT FUNCTIONALITIES
The paper aims to present the author’s vision about the possibility of applying artificial intelligence in improving the functionality of products/services from series to series by monitoring the functionality of users, on the market and in all other environments where elements for the analysis of the improvement of individual product functionalities can be found. The paper gives a clear position on the constituent elements that should make up such a functional model with all the associated elements and connections with external entities, as well as a description of the product/service improvement cycle using artificial intelligence. Artificial intelligence is not a supporting part of the model, but used as a support for deciding whether and to what extent certain proposed existing functionality will be improved or new functionality will be added to the product/service. Artificial intelligence certainly opens a new stage of the industrial revolution because it’s a big step forward in production with its technological capacity.
- Open Access
- 1 January 2024
- Published by Centre for Evaluation in Education and Science (CEON/CEES)
- No. IV Ecology,p. 550-558
Life cycle and recycling of clothing
The paper emphasizes that the life cycle and production process of an article of clothing includes a large number of stages such as: production of raw materials and fibers; production of fabrics, knitwear, non-woven textiles, etc.; design; tailoring, sewing and finishing of clothes; distribution; retail; phase of use and disposal of clothing-recycling or disposal. All this leads to the textile industry creating tens of millions of tons of textile waste annually on a global scale. Therefore, the need to find a solution to the complex production process of clothes in order to reduce the negative impact of the fashion industry on the environment is becoming more and more important. Various strategies for solving the problem of textile waste are also described. In the end, the conclusion is drawn that fashion companies pay more and more attention to the improvement of the products themselves as well as to the extension of the lifespan of the products themselves. For a typical textile product, 7 characteristic life stages through which it passes are described: concept and design stages, engineering stages, production stages, distribution and application stages, use and service activities (dry cleaning and washing), second life cycle stages (reuse) and end-of-cycle stages (recycling or disposal).
- 1 January 2024
- Published by Centre for Evaluation in Education and Science (CEON/CEES)
- No. IV Ecology,p. 550-558
Open AccessLife cycle and recycling of clothing
The paper emphasizes that the life cycle and production process of an article of clothing includes a large number of stages such as: production of raw materials and fibers; production of fabrics, knitwear, non-woven textiles, etc.; design; tailoring, sewing and finishing of clothes; distribution; retail; phase of use and disposal of clothing-recycling or disposal. All this leads to the textile industry creating tens of millions of tons of textile waste annually on a global scale. Therefore, the need to find a solution to the complex production process of clothes in order to reduce the negative impact of the fashion industry on the environment is becoming more and more important. Various strategies for solving the problem of textile waste are also described. In the end, the conclusion is drawn that fashion companies pay more and more attention to the improvement of the products themselves as well as to the extension of the lifespan of the products themselves. For a typical textile product, 7 characteristic life stages through which it passes are described: concept and design stages, engineering stages, production stages, distribution and application stages, use and service activities (dry cleaning and washing), second life cycle stages (reuse) and end-of-cycle stages (recycling or disposal).