Longhui Li
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Longhui Li has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Qingshan Jiang
College of Marine Equipment and Mechanical Engineering, Jimei University, Xiamen 361000, China
2 shared publications - Xiuyu Chen
College of Marine Equipment and Mechanical Engineering, Jimei University, Xiamen 361000, China
2 shared publications - Zhilong Xu
College of Marine Equipment and Mechanical Engineering, Jimei University, Xiamen 361021, China
2 shared publications - Dongyan Lin
College of Marine Equipment and Mechanical Engineering, Jimei University, Xiamen 361000, China
1 shared publication - Heng Liu
China Railway First Group Urban Track Transport Engineering Co., Ltd., Xi’an 710054, China
1 shared publication - Huanbin Xu
College of Marine Equipment and Mechanical Engineering, Jimei University, Xiamen 361000, China
1 shared publication
Latest Publications
- Open Access
Effect of Oblique LSP on the Wear Resistance of Plasma-Nitrided H13 Tool Steel
H13 tool steel is widely used in precision injection molds; however, severe wear in confined regions, such as ejector pin holes, limits its service life, while conventional strengthening techniques remain difficult to apply in these areas. In this study, a combined plasma nitriding and oblique laser shock peening (OLSP) treatment was proposed, and the effects of laser incidence angle on microstructure, mechanical properties, and wear behavior were systematically investigated through electron backscatter diffraction (EBSD), X-ray diffraction (XRD) residual stress analysis, and ball-on-disk (BOD) wear tests. The results demonstrate that OLSP promotes grain refinement, dislocation accumulation, and the introduction of high-magnitude compressive residual stress. The NLSP1 sample exhibited the optimum strengthening effect, with a maximum compressive residual stress of −1033 MPa. It also achieved the lowest wear depth, wear volume, and specific wear rate, with a specific wear rate of 1.64 × 10−6 mm3/(N·m), representing a 54.3% reduction compared with the untreated sample. The enhanced wear resistance was attributed to the synergistic effects of hardness improvement, microstructural refinement, and compressive residual stress. These findings demonstrate that optimizing the laser incidence angle can improve strengthening efficiency and provide an effective strategy for surface modification of critical regions in complex molds.
Open AccessEffect of Oblique LSP on the Wear Resistance of Plasma-Nitrided H13 Tool Steel
H13 tool steel is widely used in precision injection molds; however, severe wear in confined regions, such as ejector pin holes, limits its service life, while conventional strengthening techniques remain difficult to apply in these areas. In this study, a combined plasma nitriding and oblique laser shock peening (OLSP) treatment was proposed, and the effects of laser incidence angle on microstructure, mechanical properties, and wear behavior were systematically investigated through electron backscatter diffraction (EBSD), X-ray diffraction (XRD) residual stress analysis, and ball-on-disk (BOD) wear tests. The results demonstrate that OLSP promotes grain refinement, dislocation accumulation, and the introduction of high-magnitude compressive residual stress. The NLSP1 sample exhibited the optimum strengthening effect, with a maximum compressive residual stress of −1033 MPa. It also achieved the lowest wear depth, wear volume, and specific wear rate, with a specific wear rate of 1.64 × 10−6 mm3/(N·m), representing a 54.3% reduction compared with the untreated sample. The enhanced wear resistance was attributed to the synergistic effects of hardness improvement, microstructural refinement, and compressive residual stress. These findings demonstrate that optimizing the laser incidence angle can improve strengthening efficiency and provide an effective strategy for surface modification of critical regions in complex molds.
- Open Access
The Effects of Different Ultrasonic Composite Surface Modifications on the Properties of H13 Steel for Shield Tunnel Machine Cutter Ring
Tunnel boring machines (TBMs) are exposed to the impact of the ground shattering force and the friction of sandstone during excavation work, and are prone to wear and breakage, and other failures. Traditional heat treatment processes cannot simultaneously achieve the required high-energy composite structure of hard external and tough internal properties for cutter rings, leading to inadequate wear resistance and impact toughness under working conditions. This study utilizes H13 steel as the base material, and based on a study of carburizing, nitriding, and ultrasonic impact processes for H13 steel analyzing the effects of different high-energy composite modification processes on the hardness distribution, microstructure, and residual stress of H13 steel, the mechanisms by which high-energy composite modification processes affect the wear resistance and impact resistance of H13 steel are revealed. The results indicate that the wear amount and impact toughness of the sample subjected to carburizing and ultrasonic surface rolling composite strengthening were 1.9 mg and 27.34 J/cm2, demonstrating the best wear and impact resistance. This combination of properties allows the H13 steel cutter ring to achieve the optimal overall performance in terms of wear resistance and impact resistance.
Open AccessThe Effects of Different Ultrasonic Composite Surface Modifications on the Properties of H13 Steel for Shield Tunnel Machine Cutter Ring
Tunnel boring machines (TBMs) are exposed to the impact of the ground shattering force and the friction of sandstone during excavation work, and are prone to wear and breakage, and other failures. Traditional heat treatment processes cannot simultaneously achieve the required high-energy composite structure of hard external and tough internal properties for cutter rings, leading to inadequate wear resistance and impact toughness under working conditions. This study utilizes H13 steel as the base material, and based on a study of carburizing, nitriding, and ultrasonic impact processes for H13 steel analyzing the effects of different high-energy composite modification processes on the hardness distribution, microstructure, and residual stress of H13 steel, the mechanisms by which high-energy composite modification processes affect the wear resistance and impact resistance of H13 steel are revealed. The results indicate that the wear amount and impact toughness of the sample subjected to carburizing and ultrasonic surface rolling composite strengthening were 1.9 mg and 27.34 J/cm2, demonstrating the best wear and impact resistance. This combination of properties allows the H13 steel cutter ring to achieve the optimal overall performance in terms of wear resistance and impact resistance.