Anatoly S. Krotov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Anatoly S. Krotov has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Oleg V. Startsev
Yakut Scientific Centre of the Siberian Branch of the Russian Academy of Sciences, Yakutsk 766980, Russia
3 shared publications - Anatoli. K. Kychkin
Larionov Institute of the Physical-Technical Problems of the North of the Siberian Branch of the Russian Academy of Sciences – Division of Federal Research Center “The Yakut Scientific Center of the Siberian Branch of the Russian Academy of Sciences
2 shared publications - Anna A. Gavrilieva
Larionov Institute of the Physical-Technical Problems of the North of the Siberian Branch of the Russian Academy of Sciences – Division of Federal Research Center “The Yakut Scientific Center of the Siberian Branch of the Russian Academy of Sciences
2 shared publications - Mikhail P. Lebedev
Federal Research Center “Yakutsk Scientific Center of the Siberian Branch of the Russian Academy of Sciences”, Yakutsk, Russia
2 shared publications - Aisen A. Kychkin
Federal Research Centre “The Yakut Scientific Centre of the Siberian Branch of the Russian Academy of Sciences”, 2, Petrovskogo str., Yakutsk 677000, Russia
1 shared publication - G.V. Kornienko1 shared publication
Latest Publications
- 1 January 2026
- Published by Akademizdatcenter Nauka in Доклады Российской академии наук. Химия, науки о материалах / Doklady Chemistry
- Vol. 525 (1) , 102-111
THE IN-PHASE CHANGES IN MASS AND SHEAR MODULUS OF REINFORCED FIBRE POLYMERS DURING OUTDOOR EXPOSURE
In this paper, there are studies of the abrupt changes in the curve direction of the mass and in-plane shear modulus changing of glass reinforced fibre polymer VPS-48 and carbon reinforced fibre polymers KMKU-3m, VKU-39 and VKU-45 during 1 year of outdoor exposure on the Black Sea coast of Russia, in a humid subtropical climate. The in-phase change in the mass or in the in the in-plane shear modulus, when one of them falls or jumps for all the materials at the same time, was shown. The relations for calculating the in-phase indexes of the mass and the shear modulus changes of materials are obtained depending on the sensitivity threshold level for measuring the parameters. Two factors that promote the drops and jumps of reinforced fibre polymers shear modulus during outdoor weathering were variable moisture content and the deposition of sea salt on the sample surfaces.
- 1 January 2026
- Published by Akademizdatcenter Nauka in Доклады Российской академии наук. Химия, науки о материалах / Doklady Chemistry
- Vol. 525 (1) , 102-111
THE IN-PHASE CHANGES IN MASS AND SHEAR MODULUS OF REINFORCED FIBRE POLYMERS DURING OUTDOOR EXPOSURE
In this paper, there are studies of the abrupt changes in the curve direction of the mass and in-plane shear modulus changing of glass reinforced fibre polymer VPS-48 and carbon reinforced fibre polymers KMKU-3m, VKU-39 and VKU-45 during 1 year of outdoor exposure on the Black Sea coast of Russia, in a humid subtropical climate. The in-phase change in the mass or in the in the in-plane shear modulus, when one of them falls or jumps for all the materials at the same time, was shown. The relations for calculating the in-phase indexes of the mass and the shear modulus changes of materials are obtained depending on the sensitivity threshold level for measuring the parameters. Two factors that promote the drops and jumps of reinforced fibre polymers shear modulus during outdoor weathering were variable moisture content and the deposition of sea salt on the sample surfaces.
- Open Access
Durability of Basalt- and Glass Fiber-Reinforced Polymers: Influence of Internal Stresses, Mass Loss Modeling, and Mechanical/Thermomechanical Properties Under Extreme Cold Climate Exposure
The durability of basalt fiber-reinforced polymer (BFRP) and glass fiber-reinforced polymer (GFRP) composites was evaluated under extreme cold conditions in Yakutsk ( to °C. Laminates (18 layers, epoxy CYD-128) were exposed outdoors for three years. Mechanical testing showed tensile strength and modulus reductions of 22–32% for GFRP, compared with only 6–12% for BFRP. Dynamic mechanical analysis indicated that the glass transition temperature decreased by 11–14 °C in GFRP and 4–6 °C in BFRP. Mass loss kinetics were studied on specimens of different sizes (10 × 10, 20 × 20, and 40 × 40 mm) over 405 days. Seasonal sorption ranged between 0.01–0.19%, while long-term degradation followed a Fickian law with diffusion coefficients of degradation products from to . A diffusion-based model was proposed, where total mass change is represented as the superposition of reversible sorption and irreversible degradation. The model accurately reproduced experimental trends, highlighting the higher resistance of BFRP. Surface morphology analysis revealed matrix erosion and microcracking on exposed surfaces, with average roughness increasing from 1.61–5.61 µm to 5.86–11.73 µm. Thermomechanical analysis confirmed that BFRP maintained more stable coefficients of linear thermal expansion ( to °C) than GFRP, reducing thermally induced stresses during seasonal cycles. These findings demonstrate the superior stability of BFRP compared with GFRP under cold-climate exposure. Comparison of experimental results with mathematical modeling demonstrated that the primary cause of polymer matrix degradation is the action of abrupt internal stresses arising during thermal cycling under extreme cold climate conditions.Open AccessDurability of Basalt- and Glass Fiber-Reinforced Polymers: Influence of Internal Stresses, Mass Loss Modeling, and Mechanical/Thermomechanical Properties Under Extreme Cold Climate Exposure
The durability of basalt fiber-reinforced polymer (BFRP) and glass fiber-reinforced polymer (GFRP) composites was evaluated under extreme cold conditions in Yakutsk ( to °C. Laminates (18 layers, epoxy CYD-128) were exposed outdoors for three years. Mechanical testing showed tensile strength and modulus reductions of 22–32% for GFRP, compared with only 6–12% for BFRP. Dynamic mechanical analysis indicated that the glass transition temperature decreased by 11–14 °C in GFRP and 4–6 °C in BFRP. Mass loss kinetics were studied on specimens of different sizes (10 × 10, 20 × 20, and 40 × 40 mm) over 405 days. Seasonal sorption ranged between 0.01–0.19%, while long-term degradation followed a Fickian law with diffusion coefficients of degradation products from to . A diffusion-based model was proposed, where total mass change is represented as the superposition of reversible sorption and irreversible degradation. The model accurately reproduced experimental trends, highlighting the higher resistance of BFRP. Surface morphology analysis revealed matrix erosion and microcracking on exposed surfaces, with average roughness increasing from 1.61–5.61 µm to 5.86–11.73 µm. Thermomechanical analysis confirmed that BFRP maintained more stable coefficients of linear thermal expansion ( to °C) than GFRP, reducing thermally induced stresses during seasonal cycles. These findings demonstrate the superior stability of BFRP compared with GFRP under cold-climate exposure. Comparison of experimental results with mathematical modeling demonstrated that the primary cause of polymer matrix degradation is the action of abrupt internal stresses arising during thermal cycling under extreme cold climate conditions. - Open Access
Size Effects in Climatic Aging of Epoxy Basalt Fiber Reinforcement Bar
The purpose of this study was to obtain information on the influence of the size factor on the climatic aging of circular fiber plastics produced by pultrusion. The kinetics of moisture transfer was obtained in humidification and drying modes at 60 °C in samples of epoxy basalt fiber reinforcement bars: after 28 months of exposure in the extremely cold climate of Yakutsk and 30 months of exposure in the moderately warm climate of Gelendzhik. It was shown that the 2D Langmuir model adequately describes the kinetics. The diffusion coefficients in the reinforcement direction for bars with diameters of 6, 8, 10, 16 and 20 mm turned out to be significantly higher than in the radial direction. To clarify the aging mechanism of the bars and the tensile, compressive and bending strength, the coefficient of linear thermal expansion and the glass transition temperature of the epoxy matrix of the bars with a diameter of 6, 8 and 10 mm after 51 months of exposure in Yakutsk and 54 months of exposure in Gelendzhik were measured. It was shown that after climatic exposure, the deformability of the bars decreased with increasing diameter of the bar; the glass transition temperature increased more significantly in the bar with a smaller diameter. In 6 mm diameter bars, the compressive and bending strength limits decreased by 10–25 % due to the plasticizing effect of moisture. With the same depth of moisture penetration into the volume of the samples, its effect on the strength of thin bars was significant, and for thick bars, it was insignificant. An increase in the glass transition temperature by 6 °C, associated with the additional curing of the polymer matrix, occurred in the surface layer of the epoxy basalt fiber reinforcement bars and was revealed in bars with a smaller diameter.
Open AccessSize Effects in Climatic Aging of Epoxy Basalt Fiber Reinforcement Bar
The purpose of this study was to obtain information on the influence of the size factor on the climatic aging of circular fiber plastics produced by pultrusion. The kinetics of moisture transfer was obtained in humidification and drying modes at 60 °C in samples of epoxy basalt fiber reinforcement bars: after 28 months of exposure in the extremely cold climate of Yakutsk and 30 months of exposure in the moderately warm climate of Gelendzhik. It was shown that the 2D Langmuir model adequately describes the kinetics. The diffusion coefficients in the reinforcement direction for bars with diameters of 6, 8, 10, 16 and 20 mm turned out to be significantly higher than in the radial direction. To clarify the aging mechanism of the bars and the tensile, compressive and bending strength, the coefficient of linear thermal expansion and the glass transition temperature of the epoxy matrix of the bars with a diameter of 6, 8 and 10 mm after 51 months of exposure in Yakutsk and 54 months of exposure in Gelendzhik were measured. It was shown that after climatic exposure, the deformability of the bars decreased with increasing diameter of the bar; the glass transition temperature increased more significantly in the bar with a smaller diameter. In 6 mm diameter bars, the compressive and bending strength limits decreased by 10–25 % due to the plasticizing effect of moisture. With the same depth of moisture penetration into the volume of the samples, its effect on the strength of thin bars was significant, and for thick bars, it was insignificant. An increase in the glass transition temperature by 6 °C, associated with the additional curing of the polymer matrix, occurred in the surface layer of the epoxy basalt fiber reinforcement bars and was revealed in bars with a smaller diameter.