Pengcheng Xue
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Pengcheng Xue has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Jun Zhan
National Key Laboratory of Automotive Chassis Integration and Bionics, Jilin University, Changchun 130025, China
2 shared publications - Hao Jin
School of Mechanical Engineering, Sichuan University of Science and Engineering, Yibin 644005, China
1 shared publication - Hao Jin
School of Mechanical Engineering, Sichuan University of Science & Engineering, Yibin 644005, China
1 shared publication - Haoyuan Chen
National Key Laboratory of Automotive Chassis Integration and Bionics, Jilin University, Changchun 130025, China
1 shared publication - Hsin Guan
National Key Laboratory of Automotive Chassis Integration and Bionics, Jilin University, Changchun 130025, China
1 shared publication - Hsin Guan
National Key Laboratory of Automotive Chassis Integration and Bionics, Jilin University, Changchun 130025, China
1 shared publication
Latest Publications
- Open Access
- 1 August 2026
- Published by MDPI AG in Electronics
- Vol. 15 (15) , 3398
Torque Coordination Control for Dual-Drive-Axle Electric Commercial Vehicles Under Wheel-Speed Signal Loss
For 6 × 4 dual-drive-axle battery electric tractors subject to intermediate-axle wheel-speed signal loss, the drive-wheel slip state is difficult to determine under adhesion-limited driving conditions, which can readily lead to drive torque distribution mismatch between the intermediate and rear axles and excessive slip of the intermediate-axle drive wheels. To address the above problems, this paper proposes a torque coordination control method for dual-drive-axle battery electric commercial vehicles. First, a drive-axle slip ratio is constructed based on the motor speed of the drive axle to enable axle-level characterization of the drive-axle slip state under wheel-speed signal loss. Second, the drive-axle slip state is identified using the local variation relationship between the ground driving force and the drive-axle slip ratio, and the reference slip ratio of the drive axle and the wheel-end transmissible torque limit are determined. Then, a hierarchical torque coordination control method is established. In the upper layer, with convergence of the drive-axle slip ratios of the intermediate and rear axles as the objective, the wheel-end transmissible torque limit is introduced for inter-axle drive torque distribution and constraint handling. In the lower layer, super-twisting sliding mode control is employed to perform anti-slip correction on the target torque of the drive axle. Finally, the proposed method is validated in a TruckSim/Simulink co-simulation environment. The results show that, under drive-wheel speed signal loss, the proposed method can achieve reasonable drive torque distribution between the intermediate and rear axles under adhesion-limited driving conditions, suppress excessive slip of the drive axles, and improve the smoothness of the vehicle longitudinal response.
- 1 August 2026
- Published by MDPI AG in Electronics
- Vol. 15 (15) , 3398
Open AccessTorque Coordination Control for Dual-Drive-Axle Electric Commercial Vehicles Under Wheel-Speed Signal Loss
For 6 × 4 dual-drive-axle battery electric tractors subject to intermediate-axle wheel-speed signal loss, the drive-wheel slip state is difficult to determine under adhesion-limited driving conditions, which can readily lead to drive torque distribution mismatch between the intermediate and rear axles and excessive slip of the intermediate-axle drive wheels. To address the above problems, this paper proposes a torque coordination control method for dual-drive-axle battery electric commercial vehicles. First, a drive-axle slip ratio is constructed based on the motor speed of the drive axle to enable axle-level characterization of the drive-axle slip state under wheel-speed signal loss. Second, the drive-axle slip state is identified using the local variation relationship between the ground driving force and the drive-axle slip ratio, and the reference slip ratio of the drive axle and the wheel-end transmissible torque limit are determined. Then, a hierarchical torque coordination control method is established. In the upper layer, with convergence of the drive-axle slip ratios of the intermediate and rear axles as the objective, the wheel-end transmissible torque limit is introduced for inter-axle drive torque distribution and constraint handling. In the lower layer, super-twisting sliding mode control is employed to perform anti-slip correction on the target torque of the drive axle. Finally, the proposed method is validated in a TruckSim/Simulink co-simulation environment. The results show that, under drive-wheel speed signal loss, the proposed method can achieve reasonable drive torque distribution between the intermediate and rear axles under adhesion-limited driving conditions, suppress excessive slip of the drive axles, and improve the smoothness of the vehicle longitudinal response.
- Open Access
- 11 October 2024
- Published by MDPI AG in Electronics
- Vol. 13 (20) , 4006
Comprehensive Preview Decision Method for Direction and Speed of Intelligent Vehicle Based on Rules and Learning
Decision-making is a key part of autonomous driving systems. Human-like decision-making in complex scenarios is important for enhancing drivers’ trust in and acceptance of autonomous driving systems. In order to improve their human-like features and their adaptability to complex scenarios, this paper proposes a comprehensive preview decision method for direction and speed based on rules and learning. First, a decision-making structure including maneuvering ability judgment, motion trajectory prediction, safety judgment, legitimacy judgment, comprehensive performance evaluation, and parameters learning is presented. Second, a learning method for the longitudinal safety distance threshold based on a BP neural network is introduced. Third, inverse reinforcement learning (IRL) is used to learn the comprehensive performance evaluation weight coefficient for different driving styles. Finally, the DJI AD4CHE dataset is processed and used to train the parameters. Car-following and lane-changing scenarios are simulated to verify the effectiveness of decision-making. The simulation results show that the proposed method can reflect human-like decision-making in multiple scenarios.
- 11 October 2024
- Published by MDPI AG in Electronics
- Vol. 13 (20) , 4006
Open AccessComprehensive Preview Decision Method for Direction and Speed of Intelligent Vehicle Based on Rules and Learning
Decision-making is a key part of autonomous driving systems. Human-like decision-making in complex scenarios is important for enhancing drivers’ trust in and acceptance of autonomous driving systems. In order to improve their human-like features and their adaptability to complex scenarios, this paper proposes a comprehensive preview decision method for direction and speed based on rules and learning. First, a decision-making structure including maneuvering ability judgment, motion trajectory prediction, safety judgment, legitimacy judgment, comprehensive performance evaluation, and parameters learning is presented. Second, a learning method for the longitudinal safety distance threshold based on a BP neural network is introduced. Third, inverse reinforcement learning (IRL) is used to learn the comprehensive performance evaluation weight coefficient for different driving styles. Finally, the DJI AD4CHE dataset is processed and used to train the parameters. Car-following and lane-changing scenarios are simulated to verify the effectiveness of decision-making. The simulation results show that the proposed method can reflect human-like decision-making in multiple scenarios.