Wenqing Xie
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Wenqing Xie has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Guiping Ren
The Key Laboratory of Mineral Resources in Western China (Gansu Province), School of Earth Sciences, Lanzhou University, Lanzhou, China
2 shared publications - Jiqiang Zhou
Gansu Nonferrous Engineering Survey, Design and Research Institute, Lanzhou 730000, China
2 shared publications - Lei Wang
Gansu Nonferrous Engineering Survey, Design and Research Institute, Lanzhou 730000, China
2 shared publications - Yunzhu Zhou
The Key Laboratory of Mineral Resources in Western China (Gansu Province), School of Earth Sciences, Lanzhou University, Lanzhou 730000, China
2 shared publications - Baoyin Sun
The Second Geological and Mineral Exploration Institute of Gansu Provincial Bureau of Geology and Mineral Exploration and Development, Lanzhou 730000, China
1 shared publication - Runjie Qin
The Key Laboratory of Mineral Resources in Western China (Gansu Province), School of Earth Sciences, Lanzhou University, Lanzhou 730000, China
1 shared publication
Latest Publications
- Open Access
Promoting Electricity Production and Cr (VI) Removal Using a Light–Rutile–Biochar Cathode for Microbial Fuel Cells
Microbial fuel cell (MFC) technology holds significant promise for the production of clean energy and treatment of pollutants. Nevertheless, challenges such as low power generation efficiency and the high cost of electrode materials have impeded its widespread adoption. The porous microstructure of biochar and the exceptional photocatalytic properties of rutile endow it with promising catalytic potential. In this investigation, we synthesized a novel Rutile–Biochar (Rut-Bio) composite material using biochar as a carrier and natural rutile, and explored its effectiveness as a cathode catalyst to enhance the power generation efficiency of MFCs, as well as its application in remediating heavy metal pollution. Furthermore, the impact of visible light conditions on its performance enhancement was explored. The X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM) analysis validated the successful fabrication of rutile composites loaded with biochar. The maximum current density and power density achieved by the MFCs were 153.9 mA/m2 and 10.44 mW/m2, respectively, representing a substantial increase of 113.5% and 225% compared to the control group. In addition, biochar-supported rutile MFCs showed excellent degradation performance of heavy metal pollutants under light conditions. Within 7 h, the Cr6+ degradation rate reached 95%. In contrast to the blank control group, the removal efficiency of pollutants exhibited increases of 630.8%. The cyclic degradation experiments also showcased the remarkable stability of the system over multiple cycles. This study successfully integrated natural rutile and biochar to fabricate highly efficient cathode photocatalyst composites, which not only enhanced the power generation performance of MFCs but also presented an environmentally sustainable and economically viable method for addressing heavy metal pollution.
Open AccessPromoting Electricity Production and Cr (VI) Removal Using a Light–Rutile–Biochar Cathode for Microbial Fuel Cells
Microbial fuel cell (MFC) technology holds significant promise for the production of clean energy and treatment of pollutants. Nevertheless, challenges such as low power generation efficiency and the high cost of electrode materials have impeded its widespread adoption. The porous microstructure of biochar and the exceptional photocatalytic properties of rutile endow it with promising catalytic potential. In this investigation, we synthesized a novel Rutile–Biochar (Rut-Bio) composite material using biochar as a carrier and natural rutile, and explored its effectiveness as a cathode catalyst to enhance the power generation efficiency of MFCs, as well as its application in remediating heavy metal pollution. Furthermore, the impact of visible light conditions on its performance enhancement was explored. The X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM) analysis validated the successful fabrication of rutile composites loaded with biochar. The maximum current density and power density achieved by the MFCs were 153.9 mA/m2 and 10.44 mW/m2, respectively, representing a substantial increase of 113.5% and 225% compared to the control group. In addition, biochar-supported rutile MFCs showed excellent degradation performance of heavy metal pollutants under light conditions. Within 7 h, the Cr6+ degradation rate reached 95%. In contrast to the blank control group, the removal efficiency of pollutants exhibited increases of 630.8%. The cyclic degradation experiments also showcased the remarkable stability of the system over multiple cycles. This study successfully integrated natural rutile and biochar to fabricate highly efficient cathode photocatalyst composites, which not only enhanced the power generation performance of MFCs but also presented an environmentally sustainable and economically viable method for addressing heavy metal pollution.
- Open Access
- 14 September 2024
- Published by MDPI AG in Sustainability
- Vol. 16 (18) , 8056
One-Step-Modified Biochar by Natural Anatase for Eco-Friendly Cr (VI) Removal
The global serious pollution situation urgently needs green, efficient, and sustainable development methods to achieve heavy metal pollution control. The photocatalytic properties of anatase are sufficient to achieve pollution control by providing photoelectrons to harmful heavy metals. However, since natural anatase particles tend to agglomerate and deactivate in water, most studies have been conducted to prepare TiO2–biochar nanocomposites using chemical synthesis methods. In the present study, we utilized pyrolytic sintering to load natural anatase onto biochar to obtain natural anatase–biochar (TBC) composites. Characterization tests, such as X-ray diffraction (XRD), scanning electron microscopy (SEM), and X-ray photoelectron spectroscopy (XPS), showed that anatase was uniformly partitioned into the surface and pores of biochar without destroying the lattice structure. Due to its photocatalytic properties, TBC degraded Cr (VI) by 99.63% under light conditions. This is 1.58 times higher than the dark condition. Zeta potential showed that the surface of the TBC was positively charged under acidic conditions. The charge attraction between TBC and chromium salt was involved in the efficient degradation of Cr (VI). Different sacrificial agents as well as gas purge experiments demonstrated that photoelectrons (e−) and superoxide radicals () dominated the degradation of Cr (VI). TBC has the characteristics of high efficiency, stability, and sustainability. This may provide a new idea for the preparation of photocatalytic materials and the realization of environmental protection and sustainable development through heavy metal pollution control.- 14 September 2024
- Published by MDPI AG in Sustainability
- Vol. 16 (18) , 8056
Open AccessOne-Step-Modified Biochar by Natural Anatase for Eco-Friendly Cr (VI) Removal
The global serious pollution situation urgently needs green, efficient, and sustainable development methods to achieve heavy metal pollution control. The photocatalytic properties of anatase are sufficient to achieve pollution control by providing photoelectrons to harmful heavy metals. However, since natural anatase particles tend to agglomerate and deactivate in water, most studies have been conducted to prepare TiO2–biochar nanocomposites using chemical synthesis methods. In the present study, we utilized pyrolytic sintering to load natural anatase onto biochar to obtain natural anatase–biochar (TBC) composites. Characterization tests, such as X-ray diffraction (XRD), scanning electron microscopy (SEM), and X-ray photoelectron spectroscopy (XPS), showed that anatase was uniformly partitioned into the surface and pores of biochar without destroying the lattice structure. Due to its photocatalytic properties, TBC degraded Cr (VI) by 99.63% under light conditions. This is 1.58 times higher than the dark condition. Zeta potential showed that the surface of the TBC was positively charged under acidic conditions. The charge attraction between TBC and chromium salt was involved in the efficient degradation of Cr (VI). Different sacrificial agents as well as gas purge experiments demonstrated that photoelectrons (e−) and superoxide radicals () dominated the degradation of Cr (VI). TBC has the characteristics of high efficiency, stability, and sustainability. This may provide a new idea for the preparation of photocatalytic materials and the realization of environmental protection and sustainable development through heavy metal pollution control.