Anindita Paul
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Anindita Paul has a total of 38 co-authors. Here are the top co-authors by number of shared publications:
- Jaime Ramirez-Angulo
Klipsch School of Electrical and Computer Engineering, New Mexico State University, Las Cruces, NM 88003, USA
10 shared publications - Antonio J. Lopez-Martin
Department of Electrical and Electronic Engineering, Public University of Navarra, 31006 Pamplona, Spain
5 shared publications Jaime Ramirez-Angulo
Instituto Technologico Superior de Poza Rica,Electronic Engineering Department,Poza Rica,Mexico
4 shared publicationsAlejandro Diaz-Sanchez
INAOE,Department of Electronics,Puebla,Mexico
3 shared publicationsFrank X. Li
Rayen School of Engineering, Youngstown State University, Youngstown, USA
3 shared publications- Jesus Huerta-Chua
Facultad de Ingeniería Civil, Universidad Veracruzana, Prolongación Av. Venustiano Carranza S/N, Poza Rica 93390, Veracruz, Mexico
3 shared publications
Latest Publications
- Open Access
- 15 April 2025
- Published by MDPI AG in Journal of Low Power Electronics and Applications
- Vol. 15 (2) , 24
0.7 V Supply SC Circuits with Relaxed Slew Rate Requirements Using GB-Enhanced Multiple-Output Class AB/AB Op-Amps
A family of improved low-voltage switched-capacitor circuits is introduced. It is based on the utilization of multiple-output class AB/AB op-amp architectures that provide true sample and hold outputs that are not subject to a reset phase as with conventional switched-capacitor circuits. This feature essentially relaxes the op-amp slew rate requirements, allowing a higher speed and simple low-voltage operation. A power-efficient GB boosting technique based on resistive local common mode feedback is used to significantly improve the GB and internal/external slew rate of the op-amps with only a 36.5% additional power dissipation.
- 15 April 2025
- Published by MDPI AG in Journal of Low Power Electronics and Applications
- Vol. 15 (2) , 24
Open Access0.7 V Supply SC Circuits with Relaxed Slew Rate Requirements Using GB-Enhanced Multiple-Output Class AB/AB Op-Amps
A family of improved low-voltage switched-capacitor circuits is introduced. It is based on the utilization of multiple-output class AB/AB op-amp architectures that provide true sample and hold outputs that are not subject to a reset phase as with conventional switched-capacitor circuits. This feature essentially relaxes the op-amp slew rate requirements, allowing a higher speed and simple low-voltage operation. A power-efficient GB boosting technique based on resistive local common mode feedback is used to significantly improve the GB and internal/external slew rate of the op-amps with only a 36.5% additional power dissipation.
- Open Access
- 24 October 2023
- Published by Institution of Engineering and Technology (IET) in Electronics Letters
- Vol. 59 (20)
±0.15 V three‐stage bulk‐driven AB OTA with 36 MHzpF/µW and 55(V/µs)pF/µW small and large‐signal figures of merit
A three‐stage rail‐to‐rail bulk‐driven class AB OTA that operates with ±0.15 V supplies and a power dissipation of 90 nW is introduced. The first two stages use resistive local common mode feedback. The OTA uses simple phase lead compensation. It has a 36 MHz.pF/μW small signal figure of merit and a 55(V/μs) pF/μW large signal figure of merit.
- 24 October 2023
- Published by Institution of Engineering and Technology (IET) in Electronics Letters
- Vol. 59 (20)
Open Access±0.15 V three‐stage bulk‐driven AB OTA with 36 MHzpF/µW and 55(V/µs)pF/µW small and large‐signal figures of merit
A three‐stage rail‐to‐rail bulk‐driven class AB OTA that operates with ±0.15 V supplies and a power dissipation of 90 nW is introduced. The first two stages use resistive local common mode feedback. The OTA uses simple phase lead compensation. It has a 36 MHz.pF/μW small signal figure of merit and a 55(V/μs) pF/μW large signal figure of merit.
- 6 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 846-849
Low Voltage CMOS Class AB Current Mirror/Precision Rectifier
A low-voltage CMOS class AB current mirror/precision rectifier is introduced that can handle positive and negative current signals much larger than the bias current. It is based on a current switch and two current mirrors. Simulations in 180nm CMOS technology with a 1v supply and a 1μA bias current show that the circuit can handle 200μA peak-to-peak bidirectional current signals with high accuracy.
- 6 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 846-849
Low Voltage CMOS Class AB Current Mirror/Precision Rectifier
A low-voltage CMOS class AB current mirror/precision rectifier is introduced that can handle positive and negative current signals much larger than the bias current. It is based on a current switch and two current mirrors. Simulations in 180nm CMOS technology with a 1v supply and a 1μA bias current show that the circuit can handle 200μA peak-to-peak bidirectional current signals with high accuracy.
- Open Access
- 24 April 2023
- Published by MDPI AG in Journal of Low Power Electronics and Applications
- Vol. 13 (2) , 28
Class AB Voltage Follower and Low-Voltage Current Mirror with Very High Figures of Merit Based on the Flipped Voltage Follower
The application of the flipped voltage follower to implement two high-performance circuits is presented: (1) The first is a class AB cascode flipped voltage follower that shows an improved slew rate and an improved bandwidth by very large factors and that has a higher output range than the conventional flipped voltage follower. It has a small signal figure of merit FOMSS = 46 MHz pF/µW and a current efficiency figure of merit FOMCE = 118. This is achieved by just introducing an additional output current sourcing PMOS transistor (P-channel Metal Oxide Semiconductor Field Effect Transistor) that provides dynamic output current enhancement and increases the quiescent power dissipation by less than 10%. (2) The other is a high-performance low-voltage current mirror with a nominal gain accuracy better than 0.01%, 0.212 Ω input resistance, 112 GΩ output resistance, 1 V supply voltage requirements, 0.15 V input, and 0.2 V output compliance voltages. These characteristics are achieved by utilizing two auxiliary amplifiers and a level shifter that increase the power dissipation just moderately. Post-layout simulations verify the performance of the circuits in a commercial 180 nm CMOS (Complementary Metal Oxide Semiconductor) technology.
- 24 April 2023
- Published by MDPI AG in Journal of Low Power Electronics and Applications
- Vol. 13 (2) , 28
Open AccessClass AB Voltage Follower and Low-Voltage Current Mirror with Very High Figures of Merit Based on the Flipped Voltage Follower
The application of the flipped voltage follower to implement two high-performance circuits is presented: (1) The first is a class AB cascode flipped voltage follower that shows an improved slew rate and an improved bandwidth by very large factors and that has a higher output range than the conventional flipped voltage follower. It has a small signal figure of merit FOMSS = 46 MHz pF/µW and a current efficiency figure of merit FOMCE = 118. This is achieved by just introducing an additional output current sourcing PMOS transistor (P-channel Metal Oxide Semiconductor Field Effect Transistor) that provides dynamic output current enhancement and increases the quiescent power dissipation by less than 10%. (2) The other is a high-performance low-voltage current mirror with a nominal gain accuracy better than 0.01%, 0.212 Ω input resistance, 112 GΩ output resistance, 1 V supply voltage requirements, 0.15 V input, and 0.2 V output compliance voltages. These characteristics are achieved by utilizing two auxiliary amplifiers and a level shifter that increase the power dissipation just moderately. Post-layout simulations verify the performance of the circuits in a commercial 180 nm CMOS (Complementary Metal Oxide Semiconductor) technology.
- 28 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 654-658
Fully Differential Power-Efficient AB Miller Op-amp for a Wide Range of Capacitive and Resistive Loads
A fully differential, power-efficient class AB Miller op-amp with accurate control of the output quiescent current is introduced. It can drive a wide range of resistive (200$\Omega$-1M$\Omega$) and capacitive loads (5pF-300pF). It has large dynamic and static current efficiencies of 8.6 and 7.9 and small-signal figures of merit higher than 7.4 for (1M $\Omega-200\Omega$) resistive load.
- 28 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 654-658
Fully Differential Power-Efficient AB Miller Op-amp for a Wide Range of Capacitive and Resistive Loads
A fully differential, power-efficient class AB Miller op-amp with accurate control of the output quiescent current is introduced. It can drive a wide range of resistive (200$\Omega$-1M$\Omega$) and capacitive loads (5pF-300pF). It has large dynamic and static current efficiencies of 8.6 and 7.9 and small-signal figures of merit higher than 7.4 for (1M $\Omega-200\Omega$) resistive load.
- Open Access
- 8 February 2022
- Published by MDPI AG in Journal of Low Power Electronics and Applications
- Vol. 12 (1) , 9
Fully Differential Miller Op-Amp with Enhanced Large- and Small-Signal Figures of Merit
A highly power-efficient, fully differential Miller op-amp with accurately controlled output quiescent current is introduced. The op-amp can drive both capacitive and resistive load due to the presence of the auxiliary amplifier. This amplifier helps to achieve class AB operation of the proposed op-amp. The fully differential auxiliary amplifier is compact and uses a resistive local common-mode feedback network. It consumes only 6% of the total current of the op-amp. The proposed op-amp has several innovative features. Incorporating the auxiliary amplifier helps to improve the unity gain frequency, power efficiency, slew-rate, and common-mode rejection ratio of the proposed op-amp. It can drive a wide range of resistive (200 Ω–1 MΩ) and capacitive loads (5 pF–300 pF). The op-amp has a large signal dynamic current efficiency of 8.6 and a large signal static current efficiency of 7.9. The small-signal figure of merit is 8.7 for RL = 1 MΩ and 7.3 for RL = 200 Ω.
- 8 February 2022
- Published by MDPI AG in Journal of Low Power Electronics and Applications
- Vol. 12 (1) , 9
Open AccessFully Differential Miller Op-Amp with Enhanced Large- and Small-Signal Figures of Merit
A highly power-efficient, fully differential Miller op-amp with accurately controlled output quiescent current is introduced. The op-amp can drive both capacitive and resistive load due to the presence of the auxiliary amplifier. This amplifier helps to achieve class AB operation of the proposed op-amp. The fully differential auxiliary amplifier is compact and uses a resistive local common-mode feedback network. It consumes only 6% of the total current of the op-amp. The proposed op-amp has several innovative features. Incorporating the auxiliary amplifier helps to improve the unity gain frequency, power efficiency, slew-rate, and common-mode rejection ratio of the proposed op-amp. It can drive a wide range of resistive (200 Ω–1 MΩ) and capacitive loads (5 pF–300 pF). The op-amp has a large signal dynamic current efficiency of 8.6 and a large signal static current efficiency of 7.9. The small-signal figure of merit is 8.7 for RL = 1 MΩ and 7.3 for RL = 200 Ω.
- 9 August 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1094-1099
Compact Power-Efficient Static Class-AB Miller Op-amp with Enhanced Large and Small Signal Figures of Merit
A class-AB Miller op-amp with symmetrical and significantly enhanced slew-rate and accurately controlled output quiescent current is introduced. It can drive a wide range of resistive and capacitive loads. The output currents can be a factor 16 times higher than the total op-amp quiescent current. Power-efficient static class-AB operation is achieved by including a simple low-power auxiliary amplifier with resistive local common-mode feedback. It has the small-signal figure of merit FOM SS of 28 and 27 for R L =1MΩ and 200Ω.
- 9 August 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1094-1099
Compact Power-Efficient Static Class-AB Miller Op-amp with Enhanced Large and Small Signal Figures of Merit
A class-AB Miller op-amp with symmetrical and significantly enhanced slew-rate and accurately controlled output quiescent current is introduced. It can drive a wide range of resistive and capacitive loads. The output currents can be a factor 16 times higher than the total op-amp quiescent current. Power-efficient static class-AB operation is achieved by including a simple low-power auxiliary amplifier with resistive local common-mode feedback. It has the small-signal figure of merit FOM SS of 28 and 27 for R L =1MΩ and 200Ω.
- Open Access
- 26 July 2021
- Published by MDPI AG in Journal of Low Power Electronics and Applications
- Vol. 11 (3) , 31
Implementation of Power-Efficient Class AB Miller Amplifiers Using Resistive Local Common-Mode Feedback
An approach to implement single-ended power-efficient static class-AB Miller op-amps with symmetrical and significantly enhanced slew-rate and accurately controlled output quiescent current is introduced. The proposed op-amp can drive a wide range of resistive and capacitive loads. The output positive and negative currents can be much higher than the total op-amp quiescent current. The enhanced performance is achieved by utilizing a simple low-power auxiliary amplifier with resistive local common-mode feedback that increases the quiescent power dissipation by less than 10%. The proposed class AB op-amp is characterized by significantly enhanced large-signal dynamic, static current efficiency, and small-signal figures of merits. The dynamic current efficiency is 15.6 higher, the static current efficiency is 10.6 times higher, and the small-signal figure of merit is 2.3 times higher than the conventional class-A op-amp. A global figure of merit that determines an op-amp’s ultimate speed is 6.33 times higher than the conventional class A op-amp.
- 26 July 2021
- Published by MDPI AG in Journal of Low Power Electronics and Applications
- Vol. 11 (3) , 31
Open AccessImplementation of Power-Efficient Class AB Miller Amplifiers Using Resistive Local Common-Mode Feedback
An approach to implement single-ended power-efficient static class-AB Miller op-amps with symmetrical and significantly enhanced slew-rate and accurately controlled output quiescent current is introduced. The proposed op-amp can drive a wide range of resistive and capacitive loads. The output positive and negative currents can be much higher than the total op-amp quiescent current. The enhanced performance is achieved by utilizing a simple low-power auxiliary amplifier with resistive local common-mode feedback that increases the quiescent power dissipation by less than 10%. The proposed class AB op-amp is characterized by significantly enhanced large-signal dynamic, static current efficiency, and small-signal figures of merits. The dynamic current efficiency is 15.6 higher, the static current efficiency is 10.6 times higher, and the small-signal figure of merit is 2.3 times higher than the conventional class-A op-amp. A global figure of merit that determines an op-amp’s ultimate speed is 6.33 times higher than the conventional class A op-amp.
- Open Access
- 4 May 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 69783-69797
An Enhanced Gain-Bandwidth Class-AB Miller op-amp With 23,800 MHz·pF/mW FOM, 11-16 Current Efficiency and Wide Range of Resistive and Capacitive Loads Driving Capability
A compact power-efficient class-AB Miller op-amp is introduced. It uses a simple auxiliary circuit that enhances the op-amp’s gain-bandwidth product and helps to drive a wide range of capacitive and resistive loads with high static and dynamic current efficiency. Simple Miller compensation is used to obtain stability over a wide range of loading conditions. The op-amp’s simulation and experimental results in strong inversion with $15\mu \text{A}$ bias current and in sub-threshold with 250nA bias current are shown. Its performance is measured in terms of dynamic and static current efficiency figures of merit FOM CEDyn and FOM CEStat . and using the conventional small-signal figure of merit FOM SS . Experimental results of op-amps fabricated in a 130nm CMOS technology are shown that validate the proposed approach.
- 4 May 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 69783-69797
Open AccessAn Enhanced Gain-Bandwidth Class-AB Miller op-amp With 23,800 MHz·pF/mW FOM, 11-16 Current Efficiency and Wide Range of Resistive and Capacitive Loads Driving Capability
A compact power-efficient class-AB Miller op-amp is introduced. It uses a simple auxiliary circuit that enhances the op-amp’s gain-bandwidth product and helps to drive a wide range of capacitive and resistive loads with high static and dynamic current efficiency. Simple Miller compensation is used to obtain stability over a wide range of loading conditions. The op-amp’s simulation and experimental results in strong inversion with $15\mu \text{A}$ bias current and in sub-threshold with 250nA bias current are shown. Its performance is measured in terms of dynamic and static current efficiency figures of merit FOM CEDyn and FOM CEStat . and using the conventional small-signal figure of merit FOM SS . Experimental results of op-amps fabricated in a 130nm CMOS technology are shown that validate the proposed approach.
- Open Access
- 12 April 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 57603-57617
Super-Gain-Boosted AB-AB Fully Differential Miller Op-Amp With 156dB Open-Loop Gain and 174MV/V MHZ pF/μW Figure of Merit in 130nm CMOS Technology
A fully differential Miller op-amp with a composite input stage using resistive local common-mode feedback and regulated cascode transistors is presented here. High gain pseudo-differential auxiliary amplifiers are used to implement the regulated cascode transistors in order to boost the output impedance of the composite input stage and the open-loop gain of the op-amp. Both input and output stages operate in class AB mode. The proposed op-amp has been simulated in a 130nm commercial CMOS process technology. It operates from a 1.2V supply and has a close to rail-to-rail differential output swing. It has 156dB DC open-loop gain and 63MHz gain-bandwidth product with a 30pF capacitive load. The op-amp has a DC open-loop gain figure of merit$FOM_{AOLDC}$ of 174 (MV/V) MHz pF/$\mu \text{W}$ and large-signal figure of merit$FOM_{LS} $ of 3(V/$\mu \text{s}$ ) pF/$\mu \text{W}$ .- 12 April 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 57603-57617
Open AccessSuper-Gain-Boosted AB-AB Fully Differential Miller Op-Amp With 156dB Open-Loop Gain and 174MV/V MHZ pF/μW Figure of Merit in 130nm CMOS Technology
A fully differential Miller op-amp with a composite input stage using resistive local common-mode feedback and regulated cascode transistors is presented here. High gain pseudo-differential auxiliary amplifiers are used to implement the regulated cascode transistors in order to boost the output impedance of the composite input stage and the open-loop gain of the op-amp. Both input and output stages operate in class AB mode. The proposed op-amp has been simulated in a 130nm commercial CMOS process technology. It operates from a 1.2V supply and has a close to rail-to-rail differential output swing. It has 156dB DC open-loop gain and 63MHz gain-bandwidth product with a 30pF capacitive load. The op-amp has a DC open-loop gain figure of merit$FOM_{AOLDC}$ of 174 (MV/V) MHz pF/$\mu \text{W}$ and large-signal figure of merit$FOM_{LS} $ of 3(V/$\mu \text{s}$ ) pF/$\mu \text{W}$ .