An Van Vo
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
An Van Vo has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
- Tam Thanh Bui
Mot University Binh Duong 75000 Vietnam
1 shared publication - Tran Ngoc Tu
University of Transport and Communications
1 shared publication - Trinh Luong Mien
University of Transport and Communications
1 shared publication - Tue Duy Nguyen
MSc; Faculty of Mechanical-Electrical and Computer Engineering, School of Technology, Van Lang University , Ho Chi Minh City , Vietnam
1 shared publication
Latest Publications
- Open Access
- 30 December 2024
- Published by Universitas Indonesia in Makara Journal of Technology
- Vol. 28 (3) , 96-104
Design Modeling and CFD Simulation of Parallel Plate–Fin Heat Sink Under Natural Convection
The lifetime of electronic devices strongly depends on the junction temperature. Heat sinks are a good choice for dissipating heat because of their enhanced heat transfer areas. Plate–fin heat sinks are commonly used for electronic components because of their simple construction. Recently, computational fluid dynamics (CFD) software, such as Ansys Fluent and OpenFOAM, has been widely used and has provided effective results. Autodesk CFD is a powerful simulation tool; however, its use in heat sink research remains relatively uncommon. In this study, two plate–fin heat sinks with heights of 30 and 50 mm were first designed using heat transfer equations and then compared with Autodesk CFD simulations under natural convection conditions. Temperature inputs of 60 °C, 70 °C, and 80 °C were assigned to determine the temperature distribution along the fins, heat dissipation, fin efficiency, and fin effectiveness for both types of heat sinks. The results of the heat transfer calculations and Autodesk CFD simulations are consistent, with negligible differences. These findings indicate that Autodesk CFD can produce reliable results for heat sink design. In addition, efficiency decreases with the increase in fin height, although the effectiveness and heat dissipation of the tall (50 mm) heat sink are higher than those of the short (30 mm) heat sink. Although the 50-mm-high fin heat sink has a heat transfer area approximately 63% larger than that of the 30-mm-high fin heat sink, its heat dissipation is only approximately 40% larger than that of the 30-mm-high fin heat sink. This finding indicates that the addition of more material alone may not proportionally increase heat transfer and could lead to wasted material. Therefore, when designing heat sinks, the height of the fins should be carefully considered and optimized to enhance efficiency and conserve materials.
- 30 December 2024
- Published by Universitas Indonesia in Makara Journal of Technology
- Vol. 28 (3) , 96-104
Open AccessDesign Modeling and CFD Simulation of Parallel Plate–Fin Heat Sink Under Natural Convection
The lifetime of electronic devices strongly depends on the junction temperature. Heat sinks are a good choice for dissipating heat because of their enhanced heat transfer areas. Plate–fin heat sinks are commonly used for electronic components because of their simple construction. Recently, computational fluid dynamics (CFD) software, such as Ansys Fluent and OpenFOAM, has been widely used and has provided effective results. Autodesk CFD is a powerful simulation tool; however, its use in heat sink research remains relatively uncommon. In this study, two plate–fin heat sinks with heights of 30 and 50 mm were first designed using heat transfer equations and then compared with Autodesk CFD simulations under natural convection conditions. Temperature inputs of 60 °C, 70 °C, and 80 °C were assigned to determine the temperature distribution along the fins, heat dissipation, fin efficiency, and fin effectiveness for both types of heat sinks. The results of the heat transfer calculations and Autodesk CFD simulations are consistent, with negligible differences. These findings indicate that Autodesk CFD can produce reliable results for heat sink design. In addition, efficiency decreases with the increase in fin height, although the effectiveness and heat dissipation of the tall (50 mm) heat sink are higher than those of the short (30 mm) heat sink. Although the 50-mm-high fin heat sink has a heat transfer area approximately 63% larger than that of the 30-mm-high fin heat sink, its heat dissipation is only approximately 40% larger than that of the 30-mm-high fin heat sink. This finding indicates that the addition of more material alone may not proportionally increase heat transfer and could lead to wasted material. Therefore, when designing heat sinks, the height of the fins should be carefully considered and optimized to enhance efficiency and conserve materials.
- Open Access
- 16 April 2024
- Published by ASCEE Publications in International Journal of Robotics and Control Systems
- Vol. 4 (2) , 814-831
Cascade PID Control for Altitude and Angular Position Stabilization of 6-DOF UAV Quadcopter
UAVs are commonly used in transportation, especially in the express delivery of light cargo parcels. However, controlling UAVs is difficult because of their complex structure and wide range of operations in space. The research contribution is proposed a cascade control structure using six PID controllers for the 6-DOF UAV quadcopter, that ensures the altitude angulars positions control at the desired values and maintains flight balance stability for the 6-DOF UAV quadcopter. First, the mathematical dynamic models for the 6-DOF UAV quadcopter have been researched and developed, including the translational dynamic mathematical model and the rotational dynamic mathematical model of the 6-DOF UAV quadcopter. This is a complex object with strong nonlinearity and difficult control. And then, the article introduces the method of designing six PID controllers for 6-DOF UAV quadcopter to meet the requirements, based on applying the Ziegler-Nichols experimental method. Applying the Ziegler-Nichols experimental method makes the process of designing a UAV quadcopter control system simple, straightforward and heuristics with fast controller parameters tuning. Next, the article presents the results of modeling and simulation of the 6-DOF UAV quadcopter control system on Matlab/Simulink. The simulation results show that the six proposed PID controllers have ensured the flight balance stability at the desired altitude and angular positions with overshoot less than 20%, steady-state error less than 1%. This shows the prospect of applying the proposed PID control method to physical UAVs, easily adjusting PID parameters to suit the flight environment.
- 16 April 2024
- Published by ASCEE Publications in International Journal of Robotics and Control Systems
- Vol. 4 (2) , 814-831
Open AccessCascade PID Control for Altitude and Angular Position Stabilization of 6-DOF UAV Quadcopter
UAVs are commonly used in transportation, especially in the express delivery of light cargo parcels. However, controlling UAVs is difficult because of their complex structure and wide range of operations in space. The research contribution is proposed a cascade control structure using six PID controllers for the 6-DOF UAV quadcopter, that ensures the altitude angulars positions control at the desired values and maintains flight balance stability for the 6-DOF UAV quadcopter. First, the mathematical dynamic models for the 6-DOF UAV quadcopter have been researched and developed, including the translational dynamic mathematical model and the rotational dynamic mathematical model of the 6-DOF UAV quadcopter. This is a complex object with strong nonlinearity and difficult control. And then, the article introduces the method of designing six PID controllers for 6-DOF UAV quadcopter to meet the requirements, based on applying the Ziegler-Nichols experimental method. Applying the Ziegler-Nichols experimental method makes the process of designing a UAV quadcopter control system simple, straightforward and heuristics with fast controller parameters tuning. Next, the article presents the results of modeling and simulation of the 6-DOF UAV quadcopter control system on Matlab/Simulink. The simulation results show that the six proposed PID controllers have ensured the flight balance stability at the desired altitude and angular positions with overshoot less than 20%, steady-state error less than 1%. This shows the prospect of applying the proposed PID control method to physical UAVs, easily adjusting PID parameters to suit the flight environment.