Tina M. Hayward
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Tina M. Hayward has a total of 27 co-authors. Here are the top co-authors by number of shared publications:
- Rajesh Menon
Department of Electrical and Computer Engineering, University of Utah, Salt Lake City, UT 84112, USA
6 shared publications - Apratim Majumder
University of Utah
3 shared publications - Vishwa Pal
Indian Institute of Technology Ropar
2 shared publications Aditya Narayana Jena
Indian Institute of Technology Ropar
1 shared publicationAnita Kumari
Indian Institute of Technology Ropar
1 shared publication- Anita Kumari
Department of Physics, Indian Institute of Technology Ropar 1 , Rupnagar, Punjab 140001, India
1 shared publication
Latest Publications
- Open Access
- 1 September 2026
- Published by IOP Publishing in Journal of Optics
- Vol. 28 (9) , 095608
Space-time wave packets propagating a kilometer in air
We report on the diffraction-free propagation of space-time wave packets (STWPs) – a class of propagation-invariant pulsed beams—for ∼ 1 km in an open-air laser range in a low-turbulence scenario. Making use of ≈ 100 fs pulses (bandwidth ∼ 25 nm) at a wavelength of ≈ 1 μ m, we construct an STWP with a transverse width of ≈ 2 mm that expands to ≈ 3 mm after ∼ 500 m, and another that expands from ≈ 8 mm to ≈ 10 mm after 1 km. The propagation of the STWPs is compared with that of Gaussian wave packets of the same transverse spatial width and bandwidth. We establish a theoretical model that accounts for the key factors limiting the STWP propagation distance and suggests a path to further extending it.
- 1 September 2026
- Published by IOP Publishing in Journal of Optics
- Vol. 28 (9) , 095608
Open AccessSpace-time wave packets propagating a kilometer in air
We report on the diffraction-free propagation of space-time wave packets (STWPs) – a class of propagation-invariant pulsed beams—for ∼ 1 km in an open-air laser range in a low-turbulence scenario. Making use of ≈ 100 fs pulses (bandwidth ∼ 25 nm) at a wavelength of ≈ 1 μ m, we construct an STWP with a transverse width of ≈ 2 mm that expands to ≈ 3 mm after ∼ 500 m, and another that expands from ≈ 8 mm to ≈ 10 mm after 1 km. The propagation of the STWPs is compared with that of Gaussian wave packets of the same transverse spatial width and bandwidth. We establish a theoretical model that accounts for the key factors limiting the STWP propagation distance and suggests a path to further extending it.
- Open Access
- 28 July 2026
- Published by Springer Nature in Nature Photonics
- Vol. 20 (10) , 1240-1246
Large-scale compressive microscopy via diffractive multiplexing across a sensor array
Microscopes face a trade-off between spatial resolution, field of view and frame rate—improving one of these properties typically requires sacrificing others, owing to the limited spatiotemporal throughput of the sensor. To overcome this, we propose a new microscope that achieves snapshot gigapixel-scale imaging with a sensor array and a diffractive optical element. We improve spatiotemporal throughput in two ways. First, we capture data with an array of 48 sensors, resulting in 48× more pixels than a single sensor. Second, we use point spread function engineering and compressive sensing algorithms to fill in the missing information from the gaps between the individual sensors in the array, further increasing the spatiotemporal throughput of the system by an additional >5.4×. The array of sensors is modelled as a single large-format ‘super sensor’, with erasures corresponding to the gap areas between sensors. The sensor array is placed at the output of a (nearly) 4 f imaging system, with a diffractive optical element in the Fourier plane that generates a distributed multi-spot point spread function. This enables encoding of information from the entire super-sensor area, including the gaps. We then perform a large-scale regularized reconstruction using a direct fully shift-variant convolutional forward model, assuming that the object is sparse in some domain. Our microscope can achieve ~3 μm resolution over >5.2 cm 2 field of view at up to 120 fps, culminating in an effective total spatiotemporal throughput of 25.2 billion pixels per second. We demonstrate the versatility of our microscope in two different modes: structural imaging via dark-field contrast and functional fluorescence imaging of calcium dynamics across dozens of freely moving Caenorhabditis elegans .
- 28 July 2026
- Published by Springer Nature in Nature Photonics
- Vol. 20 (10) , 1240-1246
Open AccessLarge-scale compressive microscopy via diffractive multiplexing across a sensor array
Microscopes face a trade-off between spatial resolution, field of view and frame rate—improving one of these properties typically requires sacrificing others, owing to the limited spatiotemporal throughput of the sensor. To overcome this, we propose a new microscope that achieves snapshot gigapixel-scale imaging with a sensor array and a diffractive optical element. We improve spatiotemporal throughput in two ways. First, we capture data with an array of 48 sensors, resulting in 48× more pixels than a single sensor. Second, we use point spread function engineering and compressive sensing algorithms to fill in the missing information from the gaps between the individual sensors in the array, further increasing the spatiotemporal throughput of the system by an additional >5.4×. The array of sensors is modelled as a single large-format ‘super sensor’, with erasures corresponding to the gap areas between sensors. The sensor array is placed at the output of a (nearly) 4 f imaging system, with a diffractive optical element in the Fourier plane that generates a distributed multi-spot point spread function. This enables encoding of information from the entire super-sensor area, including the gaps. We then perform a large-scale regularized reconstruction using a direct fully shift-variant convolutional forward model, assuming that the object is sparse in some domain. Our microscope can achieve ~3 μm resolution over >5.2 cm 2 field of view at up to 120 fps, culminating in an effective total spatiotemporal throughput of 25.2 billion pixels per second. We demonstrate the versatility of our microscope in two different modes: structural imaging via dark-field contrast and functional fluorescence imaging of calcium dynamics across dozens of freely moving Caenorhabditis elegans .
- 21 July 2025
- Published by Optica Publishing Group in Optics Letters
- Vol. 50 (15) , 4670-4673
Extended depth-of-focus femtosecond laser pulses for flexible micromachining
We present a simple and efficient method for extending depth-of-focus of intense femtosecond (fs) pulses with a flat and thin multilevel diffractive lens (MDL). The MDL focuses fs-pulses at a desired distance, which remains invariant over an extended range of propagation distances, several times beyond that of a traditional lens. We have presented the results of strongly focused fs-pulses with different extended depth-of-focus obtained by two different MDLs. Further, we have shown laser filamentation with long plasma channels. We have also performed laser marking/machining in glass material with approximately constant spatial resolution over an EDOF. These findings can be exploited for high-throughput compact in-line fs-micromachining, potentially useful in micro-optics, microfluidics, and nanosurgery.
- 21 July 2025
- Published by Optica Publishing Group in Optics Letters
- Vol. 50 (15) , 4670-4673
Extended depth-of-focus femtosecond laser pulses for flexible micromachining
We present a simple and efficient method for extending depth-of-focus of intense femtosecond (fs) pulses with a flat and thin multilevel diffractive lens (MDL). The MDL focuses fs-pulses at a desired distance, which remains invariant over an extended range of propagation distances, several times beyond that of a traditional lens. We have presented the results of strongly focused fs-pulses with different extended depth-of-focus obtained by two different MDLs. Further, we have shown laser filamentation with long plasma channels. We have also performed laser marking/machining in glass material with approximately constant spatial resolution over an EDOF. These findings can be exploited for high-throughput compact in-line fs-micromachining, potentially useful in micro-optics, microfluidics, and nanosurgery.
- 27 May 2025
- Published by Optica Publishing Group in Optics Express
- Vol. 33 (11) , 23313-23321
Fresnel zone plate outperforms the metalens at high NA
Rigorous simulations challenge recent claims that metalenses outperform conventional diffractive lenses, such as fresnel zone plates (FZPs), in focusing efficiency at high numerical apertures (NAs). Across various lens diameters, FZPs exhibit a pronounced asymmetry in the shadow effect, leading to significantly higher focusing efficiency when optimally oriented. Extending this analysis, we show that conventional blazed gratings also surpass meta-gratings in efficiency. Since any linear optical element can be decomposed into local gratings, these findings broadly underscore the superiority of blazed structures over binary metastructures. Experimental characterization of an FZP with a diameter = 3 mm, a focal length = 0.2 mm, operating at λ = 634 nm, confirms the dependence of efficiency on illumination direction. We attribute this sensitivity to the axial symmetry of the FZP geometry–a feature not present in the metalens. Our results emphasize the need for rigorous, direct comparisons between meta-optics and traditional diffractive optics to ensure accurate performance assessments.
- 27 May 2025
- Published by Optica Publishing Group in Optics Express
- Vol. 33 (11) , 23313-23321
Fresnel zone plate outperforms the metalens at high NA
Rigorous simulations challenge recent claims that metalenses outperform conventional diffractive lenses, such as fresnel zone plates (FZPs), in focusing efficiency at high numerical apertures (NAs). Across various lens diameters, FZPs exhibit a pronounced asymmetry in the shadow effect, leading to significantly higher focusing efficiency when optimally oriented. Extending this analysis, we show that conventional blazed gratings also surpass meta-gratings in efficiency. Since any linear optical element can be decomposed into local gratings, these findings broadly underscore the superiority of blazed structures over binary metastructures. Experimental characterization of an FZP with a diameter = 3 mm, a focal length = 0.2 mm, operating at λ = 634 nm, confirms the dependence of efficiency on illumination direction. We attribute this sensitivity to the axial symmetry of the FZP geometry–a feature not present in the metalens. Our results emphasize the need for rigorous, direct comparisons between meta-optics and traditional diffractive optics to ensure accurate performance assessments.
- Top Cited Papers
- 1 April 2025
- Published by Optica Publishing Group in Optica
- Vol. 12 (4) , 473
Active laser cooling of a centimeter-scale torsional oscillator
Experimental tests of gravity’s fundamental nature call for mechanical systems in the quantum regime while being sensitive to gravity. Torsion pendula, historically vital in studies of classical gravity, are ideal for extending gravitational tests into the quantum realm due to their inherently high mechanical quality factor, even when mass-loaded. Here, we demonstrate laser cooling of a centimeter-scale torsional oscillator to a temperature of 10 mK (average occupancy of 6000 phonons) starting from room temperature. This is achieved by optical radiation pressure forces conditioned on a quantum-noise-limited optical measurement of the torsional mode with an imprecision 9.8 dB below its peak zero-point motion. The measurement sensitivity is the result of a “mirrored” optical lever that passively rejects extraneous spatial-mode noise by 60 dB. The high mechanical quality (1.4×107) and quantum-noise-limited measurement imprecision demonstrate the necessary ingredients for realizing the quantum ground state of torsional motion—a prerequisite for mechanical tests of gravity’s alleged quantum nature.
- 1 April 2025
- Published by Optica Publishing Group in Optica
- Vol. 12 (4) , 473
Top Cited PapersActive laser cooling of a centimeter-scale torsional oscillator
Experimental tests of gravity’s fundamental nature call for mechanical systems in the quantum regime while being sensitive to gravity. Torsion pendula, historically vital in studies of classical gravity, are ideal for extending gravitational tests into the quantum realm due to their inherently high mechanical quality factor, even when mass-loaded. Here, we demonstrate laser cooling of a centimeter-scale torsional oscillator to a temperature of 10 mK (average occupancy of 6000 phonons) starting from room temperature. This is achieved by optical radiation pressure forces conditioned on a quantum-noise-limited optical measurement of the torsional mode with an imprecision 9.8 dB below its peak zero-point motion. The measurement sensitivity is the result of a “mirrored” optical lever that passively rejects extraneous spatial-mode noise by 60 dB. The high mechanical quality (1.4×107) and quantum-noise-limited measurement imprecision demonstrate the necessary ingredients for realizing the quantum ground state of torsional motion—a prerequisite for mechanical tests of gravity’s alleged quantum nature.
- 29 October 2024
- Published by Optica Publishing Group in Applied Optics
- Vol. 64 (7) , B1-B5
Low-cost, high-volume, manufacturable 0.88 NA multi-wavelength diffractive lens array for optical document security
We design, manufacture, and characterize a high-numerical-aperture (NA=0.88, f/0.27), multi-wavelength (480 nm, 550 nm, and 650 nm) multilevel diffractive microlens array (MLA). This MLA achieves multi-wavelength focusing with a depth of focus (DoF) twice the diffraction-limited value. Each microlens in the array is closely packed with a diameter of 70 µm and a focal length of 19 µm in air. The MLA is patterned on one surface of a polymer film via UV casting, positioning the focal plane at the distal end of the polymer film. Each microlens focuses light at three design wavelengths into a focal spot with an estimated FWHM of ∼310nm. By placing this MLA directly on a standard high-resolution banknote print (minimum feature width of 10–15 µm), we demonstrate color-integral imaging for anti-counterfeiting. In contrast, refractive MLAs cannot achieve high-NA, multi-wavelength focusing or extended DoF. The extended DoF of our MLA ensures reliable performance despite variations in the polymer film’s thickness. Our MLA, produced via UV casting, enables extremely low-cost, high-volume production, making it ideal for flat optics in banknotes and document security.
- 29 October 2024
- Published by Optica Publishing Group in Applied Optics
- Vol. 64 (7) , B1-B5
Low-cost, high-volume, manufacturable 0.88 NA multi-wavelength diffractive lens array for optical document security
We design, manufacture, and characterize a high-numerical-aperture (NA=0.88, f/0.27), multi-wavelength (480 nm, 550 nm, and 650 nm) multilevel diffractive microlens array (MLA). This MLA achieves multi-wavelength focusing with a depth of focus (DoF) twice the diffraction-limited value. Each microlens in the array is closely packed with a diameter of 70 µm and a focal length of 19 µm in air. The MLA is patterned on one surface of a polymer film via UV casting, positioning the focal plane at the distal end of the polymer film. Each microlens focuses light at three design wavelengths into a focal spot with an estimated FWHM of ∼310nm. By placing this MLA directly on a standard high-resolution banknote print (minimum feature width of 10–15 µm), we demonstrate color-integral imaging for anti-counterfeiting. In contrast, refractive MLAs cannot achieve high-NA, multi-wavelength focusing or extended DoF. The extended DoF of our MLA ensures reliable performance despite variations in the polymer film’s thickness. Our MLA, produced via UV casting, enables extremely low-cost, high-volume production, making it ideal for flat optics in banknotes and document security.
- Open Access
- 19 September 2024
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 136 (11)
Generating optical vortex needle beams with a flat diffractive lens
We present a novel method for generating optical vortex needle beams (focused optical vortices with extended depth-of-focus) using a compact flat multilevel diffractive lens (MDL). Our experiments demonstrate that the MDL can produce focused optical vortices (FOVs) with topological charges l=1−4 (extendable to other l values), maintaining focus over distances significantly longer than conventional optical vortices. Specifically, FOVs exhibit non-diffracting behavior with a depth-of-focus (DOF) extended beyond 5 cm, compared to conventional optical vortices, which show continuous size increase due to diffraction. When the MDL is illuminated by an optical vortex of 3 mm diameter, it achieves a transmission efficiency of approximately 90% and extends the DOF several times beyond that of traditional lenses. Increasing the size of the input optical vortex further extends the DOF but introduces additional rings, with their number increasing proportionally to the value of l. Our approach, validated by both experimental results and numerical simulations, proves effective for beams such as optical vortex and Hermite-Gaussian modes and holds potential applications in high-resolution imaging, material processing, optical coherence tomography, and three-dimensional optical tweezers, offering a simple and efficient solution for generating non-diffracting beams.
- 19 September 2024
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 136 (11)
Open AccessGenerating optical vortex needle beams with a flat diffractive lens
We present a novel method for generating optical vortex needle beams (focused optical vortices with extended depth-of-focus) using a compact flat multilevel diffractive lens (MDL). Our experiments demonstrate that the MDL can produce focused optical vortices (FOVs) with topological charges l=1−4 (extendable to other l values), maintaining focus over distances significantly longer than conventional optical vortices. Specifically, FOVs exhibit non-diffracting behavior with a depth-of-focus (DOF) extended beyond 5 cm, compared to conventional optical vortices, which show continuous size increase due to diffraction. When the MDL is illuminated by an optical vortex of 3 mm diameter, it achieves a transmission efficiency of approximately 90% and extends the DOF several times beyond that of traditional lenses. Increasing the size of the input optical vortex further extends the DOF but introduces additional rings, with their number increasing proportionally to the value of l. Our approach, validated by both experimental results and numerical simulations, proves effective for beams such as optical vortex and Hermite-Gaussian modes and holds potential applications in high-resolution imaging, material processing, optical coherence tomography, and three-dimensional optical tweezers, offering a simple and efficient solution for generating non-diffracting beams.